Allen-Bradley 1792-IB16 Series B Bedienungsanleitung

ArmorBlock is a trademark of Allen-Bradley Co. Inc.

Publication 1792-5.3 – October 1996



Cat. No. 1792-IB16 Series B

To: See page:

Install

the ArmorBlock



Module

Connect the Wiring to the ArmorBlock Module

Communicate with Y

our ArmorBlock Module

Configure Y

our ArmorBlock Module Of

fline Using the DeviceNet

Manager Configuration T

ool 11

Configure Y

our ArmorBlock Module Online Using the DeviceNet

Manager Configuration T

ool 17

Reset Faults 25

Configure Y

our ArmorBlock Module with EDS Files

For this reference information

See page:

Default Configuration

Status indicators

Troubleshooting 38

Specifications 39

This 1792 ArmorBlockI/O block module (Cat. No. 1792-IB16)

contains I/O circuits, a built-in power supply, and a built-in DeviceNet

I/O adapter. Because of its sealed housing, this 1792 I/O block requires

no enclosure. It is compatible with PLC or SLC programmable

controllers using DeviceNet scanners. The I/O values are accessible

from the PLC or SLC programmable controller data table.

This ArmorBlock module has no switches to set. You set module

parameters using the DeviceNet Manager Software (cat. no.

1787-MGR) or similar configuration tool.

Installation Instructions

ArmorBlock 16 Input Module2

Publication 1792-5.3 – October 1996

European Union Directive Compliance

If this product is installed within the European Union or EEA regions

and has the CE mark, the following regulations apply.

EMC Directive

This apparatus is tested to meet Council Directive 89/336/EEC

Electromagnetic Compatibility (EMC) using a technical construction

file and the following standards, in whole or in part:

•EN 50081-2 EMC – Generic Emission Standard, Part 2 –

Industrial Environment

•EN 50082-2 EMC – Generic Immunity Standard, Part 2 –

Industrial Environment

The product described in this manual is intended for use in an industrial

environment.

Low Voltage Directive

This apparatus is also designed to meet Council Directive 73/23/EEC

Low Voltage, by applying the safety requirements of EN 61131–2

Programmable Controllers, Part 2 – Equipment Requirements and

Tests.

For specific information that the above norm requires, see the

appropriate sections in this manual, as well as the following

Allen-Bradley publications:

•Industrial Automation Wiring and Grounding Guidelines,

publication 1770-4.1

•Automation Systems Catalog, publication B111

ArmorBlock 16 Input Module

Publication 1792-5.3 – October 1996

Install

our ArmorBlock Module

Installation of the ArmorBlock module consists of:

•setting the node address in the ArmorBlock module

•mounting the ArmorBlock module

•connecting the wiring

•communicating with your module

•configuring the parameters

Set the Node Address

Each ArmorBlock comes with its internal program set for node address

63. To set the node address, you need the following:

•host computer with DeviceNet Manager Software (or similar

configuration software tool)

•1770-KFD RS-232 module (or similar interface)

•suitable cables to connect the 1770-KFD to your module and to

connect the 1770-KFD to your host computer

Set the node address to meet your system requirements as follows:

1. Set up a system (as shown below) to communicate with your

ArmorBlock module.

Power

from 9V DC Power-Supply Adapter

power supply

open style connector to

sealed mini-female cable

RS-232 module

host computer with the

DeviceNet Manager software

1770-KFD

ArmorBlock 16 Input Module4

Publication 1792-5.3 – October 1996

2. Using DeviceNet Manager Software, go online using the “Setup

Online Connection” selection on the utility pulldown menu.

3. The DeviceNet Driver selection screen appears.

Select the driver for your application and click on .

4. The Driver configuration screen lets you:

•set the data rate

•set the interface adapter node address

•select the interface adapter serial port

•set interface adapter baud rate

Click on to go online.

ArmorBlock 16 Input Module

Publication 1792-5.3 – October 1996

5. The bar at the bottom of the screen will tell you when you go online.

6. At the utility pulldown, select “Node Commissioning.”

7. You can set the node address on the “Device Configuration – Node

Commissioning” screen. Note that the node address “out of the box”

setting is 63. Set the desired node address per your system

requirements.

Set new node

address here.

You can also set the data rate on this screen, if required. However,

your module is shipped with the “autobaud” parameter enabled.

This assures that the module will be at the correct data rate for any

network to which it is connected. To change the data rate, you must

first disable autobaud on the parameter screen, then return to the

“Device Configuration – Node Commissioning” screen and enter

the new data rate.

8. Click on to apply the new node settings.

9. Repeat the above procedure to set the node addresses of any

additional ArmorBlock modules you want to install.

ArmorBlock 16 Input Module6

Publication 1792-5.3 – October 1996

Mount the ArmorBlock Module

Mount the block module directly to the machine or device. Complete

mounting dimensions are shown below. Note that the block dimensions

allow direct connection of a T-port tap (cat. no. 1485P-P1N5-j) to the

DeviceNet connector. (Refer to publication 1485-6.7.1 for cabling

details.)

The ArmorBlock module has a sloping top and a gap at the rear to

allow water or other liquids to run off during washdowns. The flow

through the gap prevents buildup of debris under the block.

Preferred mounting position is with the microconnectors pointing

down. However, the block can be mounted in any orientation.

ArmorBlock 16 Input Module

Publication 1792-5.3 – October 1996

Mounting Dimensions

6.24

2.63 2.5

7.74

1.90

3.055

mounting holes

for #10 screws

MOD/NET

STATUS INPUT

FAULT

NODE

ADDRESS

DATA

ARMORBLOCK

I/O

1792-IB16

(77.6)

(48.3)

(158.5)

(66.7) (63.5)

(196.6)

(184.2)

Inches

(Millimeters)

Block dimensions allow T

-port tap

connection directly onto connector

For washdown installations,

or excessively moist areas,

mount block with micro

connectors down.

Direction of liquid flow

ArmorBlock 16 Input Module8

Publication 1792-5.3 – October 1996

Connect the Wiring to the ArmorBlock Module

The block module uses quick disconnect, screw-on style connectors

for:

•I/O input wiring

•the DeviceNet connector

910

13 14

8 micro connectors for 16 input signal wiring

DeviceNet mini connector

Micro plugs are included with your module. Use these plugs to cover

and seal unused ports.

Pinout diagrams for these connectors are shown below.

!ATTENTION: All connectors must be securely

tightened to properly seal the connections against leaks

and maintain NEMA 4X and 6P requirements.

ArmorBlock 16 Input Module

Publication 1792-5.3 – October 1996

Connecting the Input Wiring

Connect input wiring to the micro connectors which screw into mating

connectors on the side of the block.

Make connections as shown below.

I/O Input Micro Connector

Pin 1 = Sensor Source Voltage Positive

Pin 2 = Signal 2

Pin 3 = Negative/Return

Pin 4 = Signal 1

(View into socket)

The signal 2 pin on the connector is used for 16 input modules only.

Use a splitter cable (or “Y” cable) to access signal 2.

Connecting the DeviceNet Wiring

Connect DeviceNet wiring to the 5-pin mini connector on the end of

the block. Connections are shown below.

DeviceNet Mini Connector Pin 1 = Drain (Bare)

Pin 2 = V+ (Red)

Pin 3 = V– (Black)

(View into pins)

Pin 4 = CAN–HI (White)

Pin 5 CAN–LO (Blue)

Note: Colors are

DeviceNet standard

ArmorBlock 16 Input Module10

Publication 1792-5.3 – October 1996

Communicate with Your ArmorBlock Module

This ArmorBlock module acts as a slave in a master/slave environment.

It is both a “polled device” and a “change of state device.”

When configured as a polled device, a master initiates communication

by sending its polled I/O message to the ArmorBlock module. The 16

input module scans the inputs and fault bit producing a response that

reflects their status.

When configured as a “change of state” device, productions occur

when an input changes or an input source voltage fault occurs. If

neither has occurred within the “expected packet rate,” a heartbeat

production occurs. This heartbeat production tells the scanner module

that the ArmorBlock module is alive and ready to communicate.

Bit 07 06 05 04 03 02 01 00

Produces 1 I7 I6 I5 I4 I3 I2 I1 I0

Produces 2 I15 I14 I13 I12 I11 I10 I9 I8

Produces 3 S Reserved

Where: I = Input

S = Sensor source voltage fault

Word Bit Description

Produces

100–07 Input bits – bit 00 corresponds to input 0, bit 01 to input 1, and

so on.

0 = input off; 1 = the input is on.

Produces

200–07 Input bits – bit 00 corresponds to input 8, bit 01 to input 9, and so

on.

0 = input off; 1 = the input is on.

Produces 00–06 Reserved

307 Sensor source voltage fault bit – this bit is set (1) when the sensor

source voltage is faulted.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley 1770-KFDG Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB8S Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1732ES-IB16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OBD Bedienungsanleitung

Allen-Bradley

Allen-Bradley Bulletin 193 E1 PLUS Benutzerhandbuch

Allen-Bradley

Allen-Bradley SERCOS 1756-M03SE/A Bedienungsanleitung

Allen-Bradley

Allen-Bradley MSR41 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1747-SCNR Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1440-DYN02-01RJ Bedienungsanleitung

Allen-Bradley

Allen-Bradley OptiSIS 1711-P05SISID050S Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-IL Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet-to-FOUNDATION Fieldbus H1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ProcessLogix B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1747-ACN15 Bedienungsanleitung

Allen-Bradley

Allen-Bradley DeviceNet 1771-SDN/C Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 755 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Handbuch

Allen-Bradley

Allen-Bradley 1771-QRD Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-16CFGM12M12LDR Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung