Allen-Bradley ProcessLogix B Series Bedienungsanleitung

Publication 1757-IN092E-EN-P - November 2007

Installation Instructions

ProcessLogix and ControlLogix System

Redundancy Module

Catalog Number 1757-SRM, series B

About This Publication

Use this publication as a guide to install the 1757-SRM, Series B ProcessLogix

and ControlLogix System Redundancy Module into the ProcessLogix or

ControlLogix Redundant chassis pair.

Topic Page

About This Publication 1

Important User Information 2

Environment and Enclosure 4

Prevent Electrostatic Discharge 5

European Hazardous Location Approval 6

About the Module 7

Redundancy System Assembly 11

Using the 1757-SRM Module Relay Terminals 15

Designate the Primary Chassis and Qualify the System 19

Install or Remove the Module Under Power 22

1757-SRM Module Fault Codes and Display Messages 26

Specifications 30

Allen-Bradley Parts

2ProcessLogix and ControlLogix System Redundancy Module

Publication 1757-IN092E-EN-P - November 2007

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of

the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you to identify a

hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment, such as a drive or motor, to alert people

that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment, such as a drive or motor, to alert people

that surfaces may reach dangerous temperatures.

ProcessLogix and ControlLogix System Redundancy Module 3

Publication 1757-IN092E-EN-P - November 2007

North American Hazardous Location Approval

The following information applies

when operating this equipment in

hazardous locations.

Informations sur l'utilisation de cet

équipement en environnements

dangereux.

Products marked CL I, “DIV 2, GP A, B, C, D” are

suitable for use in Class I Division 2 Groups A, B,

C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with

markings on the rating nameplate indicating the

hazardous location temperature code. When

combining products within a system, the most

adverse temperature code (lowest “T” number)

may be used to help determine the overall

temperature code of the system. Combinations

of equipment in your system are subject to

investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués CL I, “DIV 2, GP A, B, C, D” ne

conviennent qu'à une utilisation en environnements

de Classe I Division 2 Groupes A, B, C, D dangereux

et non dangereux. Chaque produit est livré avec des

marquages sur sa plaque d'identification qui

indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs

produits sont combinés dans un système, le code de

température le plus défavorable (code de

température le plus faible) peut être utilisé pour

déterminer le code de température global du

système. Les combinaisons d'équipements dans le

système sont sujettes à inspection par les autorités

locales qualifiées au moment de l'installation.

EXPLOSION HAZARD

Do not disconnect equipment

unless power has been

removed or the area is known

to be nonhazardous.

Do not disconnect

connections to this

equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external

connections that mate to this

equipment by using screws,

sliding latches, threaded

connectors, or other means

provided with this product.

Substitution of components

may impair suitability for

Class I, Division 2.

If this product contains

batteries, they must only be

changed in an area known to

be nonhazardous.

RISQUE D'EXPLOSION

Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher l'équipement.

Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher les connecteurs.

Fixer tous les connecteurs

externes reliés à cet

équipement à l'aide de vis,

loquets coulissants,

connecteurs filetés ou autres

moyens fournis avec ce produit.

La substitution de composants

peut rendre cet équipement

inadapté à une utilisation en

environnement de Classe I,

Division 2.

S'assurer que l'environnement

est classé non dangereux avant

de changer les piles.

WARNING AVERTISSEMENT

Allen-Bradley Parts

4ProcessLogix and ControlLogix System Redundancy Module

Publication 1757-IN092E-EN-P - November 2007

Environment and Enclosure

ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 m (6561 ft) without

derating.

This equipment is considered Group 1, Class A industrial equipment

according to IEC/CISPR Publication 11. Without appropriate

precautions, there may be potential difficulties ensuring

electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be

mounted within an enclosure that is suitably designed for those

specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from

accessibility to live parts. The enclosure must have suitable

flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or

equivalent) if non-metallic. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain

product safety certifications.

In addition to this publication, see:

•Industrial Automation Wiring and Grounding Guidelines, for additional

installation requirements, Allen-Bradley publication 1770-4.1.

•NEMA Standards publication 250 and IEC publication 60529, as

applicable, for explanations of the degrees of protection provided by

different types of enclosure.

ProcessLogix and ControlLogix System Redundancy Module 5

Publication 1757-IN092E-EN-P - November 2007

Prevent Electrostatic Discharge

Programmable Electronic Systems

Optical Ports

ATTENTION This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation, if available.

•Store the equipment in appropriate static-safe packaging when

not in use.

ATTENTION Personnel responsible for the application of safety-related

Programmable Electronic Systems (PES) shall be aware of the safety

requirements in the application of the system and shall be trained in

using the system.

ATTENTION Under certain conditions, viewing the optical port may expose the eye

to hazard. When viewed under some conditions, the optical port may

expose the eye beyond the maximum permissible exposure

recommendations.

Allen-Bradley Parts

6ProcessLogix and ControlLogix System Redundancy Module

Publication 1757-IN092E-EN-P - November 2007

European Hazardous Location Approval

European Zone 2 Certification (The following applies when the product

bears the EEx Marking).

This equipment is intended for use in potentially explosive atmospheres as

defined by European Union Directive 94/9/EC.

The LCIE (Laboratoire Central des Industries Electriques) certifies that this

equipment has been found to comply with the Essential Health and Safety

Requirements relating to the design and construction of Category 3

equipment intended for use in potentially explosive atmospheres, given in

Annex II to this Directive.

Compliance with the Essential Health and Safety Requirements has been

assured by compliance with EN 60079-15.

IMPORTANT This equipment is not resistant to sunlight or other sources of UV

radiation.

This equipment must be installed in an enclosure providing at least

IP54 protection when applied in Class I, Zone 2 environments.

This equipment shall be used withinits specified ratings defined by

Allen-Bradley.

Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 40% when

applied in Class I, Zone 2 environments.

This equipment must be used only with ATEX certified backplanes.

ProcessLogix and ControlLogix System Redundancy Module 7

Publication 1757-IN092E-EN-P - November 2007

About the Module

Use this illustration to identify the external features of the module.

Before You Begin

Before you install the module, make sure you:

•know how to handle the module.

See Prevent Electrostatic Discharge on page 5.

•understand redundant systems and redundant media.

For additional information, see the ControlLogix Redundancy System

User Manual, publication 1756-UM523.

IMPORTANT If you are using a ProcessLogix system, search for the appropriate

Knowledge Builder documentation at:

http://www.rockwellautomation.com/knowledgebase.

Fiber-

Optic

Port

Front View of 1757-SRM Module with Door Open

Front Panel

Status

Indicators

User Relay

Terminal

Allen-Bradley Parts

8ProcessLogix and ControlLogix System Redundancy Module

Publication 1757-IN092E-EN-P - November 2007

Parts List

You will need these components.

Prepare the Chassis for Module Installation

Before you install the module, you must install and connect a ControlLogix

chassis and power supply.

Chassis Type (series B) Chassis Installation Instructions

1756-A4

Publication 1756-IN080

1756-A7

1756-A10

1756-A13

1756-A17

1757-SRM

Modules

1756-A4, 1756-A7, 1756-A10,

1756-A13, or 1756-A17 Chassis 1756-PA72, 1756-PA75,

1756-PB72, or 1756-PB75

Power Supplies

PRI COM OK

REDUNDANCY MODULE

1757-SRCxxx

Fiber-optic Cable

1756-A7

Chassis

Power

Supply

ProcessLogix and ControlLogix System Redundancy Module 9

Publication 1757-IN092E-EN-P - November 2007

Power Supply Power Supply Installation Instructions

1756-PA72/C Publication 1756-IN078

1756-PB72/B

1756-PA75/B Publication 1756-IN596

1756-PB75/B

ATTENTION To comply with UL restrictions, the relay terminals must be powered

from a source compliant with Class 2.

To comply with the CE Low Voltage Directive (LVD), the relay terminals

must be powered from a source compliant with Safety Extra Low

Voltage (SELV) or Protected Extra Low Voltage (PELV).

The line voltage source for the external dc power source to the SRM

Relay Terminals must be the same as that used to power the

energizing SRM Chassis.

Allen-Bradley Parts

10 ProcessLogix and ControlLogix System Redundancy Module

Publication 1757-IN092E-EN-P - November 2007

Determine Module Slot Location

Install the 1757-SRM module in the appropriate slot in the ControlLogix

chassis. Slot 0 is the first slot and is always the leftmost slot in the rack.

Installation Requirements

Before you assemble your redundant systems, make sure your redundant

system components are identical. Specifically, these items must match:

•primary and secondary (redundant) control chassis, with all modules

in the exact same order (slot for slot).

•firmware revisions of all module partners.

Chassis Type (series B) Recommended Slot Locations for 1757-SRM Module

1756-A4 1 or 2

1756-A7 4 or 5

1756-A10 5 or 6

1756-A13 4 or 5

1756-A17 5 or 6

IMPORTANT If the primary and secondary (redundant) systems are not

assembled identically, and are not comprised of modules with

matching firmware revisions, the 1757-SRM module cannot qualify

the secondary chassis to the primary chassis.

Power Supply

Slot 0

Slot 1

Slot 2

Chassis

Slot 3

Slot 4

Slot 5

Slot 6

1756-A7 chassis is

shown in this example.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley Steuereinheit Handbücher

Allen-Bradley

Allen-Bradley PowerFlex 755 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1500 1764-MM1 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OF6VI Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OBD Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-OW Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE8H Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlNet 1786-RPCD Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix ControlNet B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CENTERLINE 2100 Bedienungsanleitung

Allen-Bradley

Allen-Bradley A Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley XM-124 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OB4D Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1762-OF4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IV32 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CENTERLINE 1500 Bedienungsanleitung

Allen-Bradley

Allen-Bradley MicroLogix 1762-IF4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock Series Handbuch

Allen-Bradley

Allen-Bradley 1747-KE Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1440-DYN02-01RJ Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1771-KA2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley CompactLogix EtherNet/IP 1768-EWEB Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1757-ABRIO Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung