Allen-Bradley FLEX I/O 1794-IB10XOB6 Bedienungsanleitung

Installation Instructions

Original Instructions

FLEX I/O Digital Input and Output Modules

Catalog Numbers

1794-IB10XOB6, 1794-IB16XOB16P

Topic Page

Important User Information 2

Environment and Enclosure 3

North American Hazardous Location Approval 4

European Hazardous Location Approval 5

Prevent Electrostatic Discharge 6

Installing Your Digital Input/output Module 8

Configuring Your Module 15

Specifications 18

Derating Curve for 1794-IB16XOB16P 23

2Rockwell Automation Publication 1794-IN083D-EN-P - July 2018

FLEX I/O Digital Input and Output Modules

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid-state Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid-

state equipment and hard-wired electromechanical devices. Because of this difference, and also because of

the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements that are associated with any particular installation, Rockwell

Automation, Inc. cannot assume responsibility or liability for actual use based on the examples

and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of

Rockwell Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you identify a

hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or motor)

to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment (for example, drive or motor) to

alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

Rockwell Automation Publication 1794-IN083D-EN-P - July 2018 3

FLEX I/O Digital Input and Output Modules

Environment and Enclosure

ATTENTION:

This equipment is intended for use in a Pollution Degree 2 industrial

environment, in overvoltage Category II applications (as defined inEN/IEC 60664-1),

at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not

provide adequate protection to radio communication services in such environments.

This equipment is supplied as open-type equipment for indoor use. It must be

mounted within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to

prevent personal injury resulting from accessibility to live parts. The enclosure

must have suitable flame-retardant properties to prevent or minimize the spread

of flame, complying with a flame spread rating of 5V A or be approved for the

application if nonmetallic. The interior of the enclosure must be accessible only by

the use of a tool. Subsequent sections of this publication may contain more

information regarding specific enclosure type ratings that are required to comply

with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines,

publication 1770-4.1, for additional installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the

degrees of protection provided by enclosures.

ATTENTION: Read this document and the documents listed in the Additional

Resources section about installation, configuration, and operation of this

equipment before you install, configure, operate, or maintain this product. Users

are required to familiarize themselves with installation and wiring instructions in

addition to requirements of all applicable codes, laws, and standards.

Installation, adjustments, putting into service, use, assembly, disassembly, and

maintenance are required to be carried out by suitably trained personnel in

accordance with applicable code of practice. In case of malfunction or damage, no

attempts at repair should be made. The module should be returned to the

manufacturer for repair. Do not dismantle the module.

4Rockwell Automation Publication 1794-IN083D-EN-P - July 2018

FLEX I/O Digital Input and Output Modules

North American Hazardous Location Approval

The following modules are North American Hazardous Location approved:

1794-IB10XOB6, 1794-IB16XOB16P

The Following Information Applies When

Operating This Equipment In Hazardous Locations.

Informations sur l’utilisation de cet équipement en

environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable

for use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product

is supplied with markings on the rating nameplate

indicating the hazardous location temperature code.

When combining products within a system, the most

adverse temperature code (lowest "T" number) may be

used to help determine the overall temperature code of

the system. Combinations of equipment in your system

are subject to investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements de Classe

I Division 2 Groupes A, B, C, D dangereux et non dangereux.

Chaque produit est livré avec des marquages sur sa plaque

d'identification qui indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs produits sont

combinés dans un système, le code de température le plus

défavorable (code de température le plus faible) peut être

utilisé pour déterminer le code de température global du

système. Les combinaisons d'équipements dans le système

sont sujettes à inspection par les autorités locales qualifiées

au moment de l'installation.

WARNING:

Explosion Hazard –

• Do not disconnect equipment

unless power has been removed

or the area is known to

be nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external connections

that mate to this equipment by

using screws, sliding latches,

threaded connectors, or other

means provided with this product.

• Substitution of components may

impair suitability for Class I,

Division 2.

AVERTISSEMENT:

Risque d’Explosion –

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher

l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les connecteurs

externes reliés à cet équipement à

l'aide de vis, loquets coulissants,

connecteurs filetés ou autres moyens

fournis avec ce produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de

Classe I, Division 2.

WARNING: When used in a Class I, Division 2, hazardous location, this equipment

must be mounted in a suitable enclosure with proper wiring method that

complies with the governing electrical codes.

Rockwell Automation Publication 1794-IN083D-EN-P - July 2018 5

FLEX I/O Digital Input and Output Modules

European Hazardous Location Approval

The following module is European Zone 2 approved: 1794-IB10XOB6.

The following applies to products marked II 3 G:

• Are intended for use in potentially explosive atmospheres as defined by European Union

Directive 2014/34/EU and has been found to comply with the Essential Health and Safety

Requirements relating to the design and construction of Category 3 equipment intended for

use in Zone 2 potentially explosive atmospheres, given in Annex II to this Directive.

• Compliance with the Essential Health and Safety Requirements has been assured by

compliance with EN 60079-15 and EN 60079-0.

• Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and

Safety Requirements relating to the design and construction of such equipment given in

Annex II to Directive 2014/34/EU. See the EC Declaration of Conformity at

http://www.rockwellautomation.com/global/certification/overview.page for details.

• The type of protection is Ex nA IIC T3 Gc according to EN 60079-15.

• Comply to Standards EN 60079-0:2012, EN 60079-15:2010, reference certificate number

DEMKO 14 ATEX 1342501X.

• Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists,

or air are unlikely to occur, or are likely to occur only infrequently and for short periods. Such

locations correspond to Zone 2 classification according to ATEX directive 2014/34/EU.

WARNING:

• This equipment is not resistant to sunlight or other sources of UV radiation.

• This equipment shall be used within its specified ratings defined by

Rockwell Automation.

• Provision shall be made to prevent the rated voltage from being exceeded by

transient disturbances of more than 140% of the peak rated voltage when

applied in Zone 2 environments.

• The instructions in the user manual shall be observed.

• This equipment must be used only with ATEX certified

Rockwell Automation backplanes.

• Earthing is accomplished through mounting of modules on rail.

• Devices shall be used in an environment of not more than Pollution Degree 2.

6Rockwell Automation Publication 1794-IN083D-EN-P - July 2018

FLEX I/O Digital Input and Output Modules

Prevent Electrostatic Discharge

Special Conditions for Safe Use

ATTENTION: This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these guidelines

when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

ATTENTION:

• This product is grounded through the DIN rail to chassis ground. Use zinc

plated chromate-passivated steel DIN rail to assure proper grounding. The use

of other DIN rail materials (for example, aluminum or plastic) that can corrode,

oxidize, or are poor conductors, can result in improper or intermittent

grounding. Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately. Be sure to ground the DIN rail

properly. Refer to Industrial Automation Wiring and Grounding Guidelines,

publication 1770-4.1, for more information.

• Do not remove or replace an Adapter Module while power is applied.

Interruption of the backplane can result in unintentional operation or

machine motion.

• Do not remove or replace a terminal base unit while power is applied.

Interruption of the backplane cab result in unintentional operation or

machine motion.

• If this equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

Rockwell Automation Publication 1794-IN083D-EN-P - July 2018 7

FLEX I/O Digital Input and Output Modules

Electrical Safety Considerations

WARNING:

• When you insert or remove the module while backplane power is on, an

electric arc can occur. This could cause an explosion in hazardous

location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

Repeated electric arcing causes excessive wear to contacts on both the module

and its mating connector. Worn contacts may create electrical resistance that

can affect module operation.

• If you insert or remove themodule while backplane power is on, an electric arc

can occur. This could cause an explosion in hazardous location installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

WARNING: If you connect or disconnect wiring while the field-side power is on,

an electrical arc can occur. This could cause an explosion in hazardous location

installations. Be sure that power is removed or the area is nonhazardous

before proceeding.

ATTENTION:

• This equipment is certified for use only within the surrounding air temperature

range of 0…55 °C (32…131 °F). The equipment must not be used outside of

this range.

• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any

cleaning agents.

At the end of its life, this equipment should be collected separately from any

unsorted municipal waste.

8Rockwell Automation Publication 1794-IN083D-EN-P - July 2018

FLEX I/O Digital Input and Output Modules

Installing Your Digital Input/output Module

The 1794-IB10XOB6 module mounts on a 1794-TB3 or 1794-TB3S terminal

base. The 1794-IB16XOB16P module mounts on a 1794-TB32 or 1794-TB32S

terminal base.

1. Rotate the keyswitch (1) on the terminal base (2) clockwise to position 2

as required for this type of module.

2. Ensure that the Flexbus connector (3) is pushed all the way to the left to

connect with the neighboring terminal base/adapter. Yo u c a nn o t i ns t a l l

the module unless the connector is fully extended.

Description Description

1Keyswitch 5Alignmentbar

2Terminalbase 6Groove

3 Flexbus connector 7 Latching mechanism

4Module

ATTENTION: During mounting of all devices, be sure that all debris (metal chips,

wire strands, etc.) is kept from falling into the module. Debris that falls into the

module could cause damage on power up.

Rockwell Automation Publication 1794-IN083D-EN-P - July 2018 9

FLEX I/O Digital Input and Output Modules

3. Make sure the pins on the bottom of the module are straight so they will

align properly with the connector in the terminal base.

4. Position the module (4) with its alignment bar (5) aligned with the

groove (6) on the terminal base.

5. Press firmly and evenly to seat the module in the terminal base unit. The

module is seated when the latching mechanism (7) is locked into

the module.

Connecting Wiring for the 1794-IB10XOB6

1. Connect individual input and output wiring to numbered terminals on

the 0...15 row (A) as indicated in the Wiring Connections for 1794-

IB10XOB6 table.

2. Connect the associated +V DC power lead of the input device to the

corresponding terminal on the 34...51 row (C) for each input as

indicated in the Wiring Connections for 1794-IB10XOB6 table. (The

+V power terminals of row (C) are internally connected together.)

3. Connect the associated input device common (3-wire devices only) and

output device common to the corresponding terminals on the 16...33

row. (B) for each input and output as indicated in the Wiring

Connections for 1794-IB10XOB6 table. (Commons are internally

connected together.)

4. Connect +V DC power to terminal 34 on the 34...51 row (C).

5. Connect V DC common to terminal 16 on the 16...33 row (B).

6. If daisychaining power to the next terminal base, connect a jumper from

terminal 51 (+V DC) on this base unit to terminal 34 on the next

base unit.

WARNING: If you insert or remove the module while backplane power is on, an

electrical arc can occur. This could cause an explosion in hazardous location

installations. Be sure that power is removed or the area is nonhazardous

before proceeding.

10 Rockwell Automation Publication 1794-IN083D-EN-P - July 2018

FLEX I/O Digital Input and Output Modules

7. If continuing DC common to the next base unit, connect a jumper from

terminal 33 (240V common L2) on this base unit to terminal 16 on the

next base unit.

Wiring Connections for 1794-IB10XOB6

Input(1)

(1) 2-wire input devices use signal and supply terminals; 3-wire devices use signal, return, and supply terminal

Signal Return Supply

Sink input

Input 0 A-0 B-17 C-35

Input 1 A-1 B-18 C-36

Input 2 A-2 B-19 C-37

Input 3 A-3 B-20 C-38

Input 4 A4 B-21 C-39

Input 5 A-5 B-22 C-40

Input 6 A-6 B-23 C-41

Input 7 A-7 B-24 C-42

Input 8 A-8 B-25 C-43

Input 9 A-9 B-27 C-44

Source output

Input 10 A-10 B-27

Input 11 A-11 B-28

Input 12 A-12 B-29

Input 13 A-13 B-30

Input 14 A-14 B-31

Input 15 A-15 B-32

+V DC C-34 to C-51 (internally connected together)

Common B-16 to B-33 (internally connected together)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Allen-Bradley E/A-System Handbücher

Allen-Bradley

Allen-Bradley CompactBlock LDX 1790D-T4T0 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA16I Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IC16 Bedienungsanleitung

Allen-Bradley

Allen-Bradley Flex I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley Series B Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1719 Ex I/O Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IT8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1794-IE12 Bedienungs- und Wartungshandbuch

Allen-Bradley

Allen-Bradley 1746 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IR8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1756 ControlLogix Bedienungsanleitung

Allen-Bradley

Allen-Bradley ArmorBlock MaXum 4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-NT8 Bedienungsanleitung

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1791-0A32 B Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1734-IB2 Bedienungsanleitung

Allen-Bradley

Allen-Bradley POINT I/O 1734-IB4D Bedienungsanleitung

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OB4D Bedienungsanleitung

Allen-Bradley

Allen-Bradley ControlLogix 1756-IF6CIS Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1746-IA4 Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1492-CM1771-LD005 Bedienungsanleitung

Allen-Bradley

Allen-Bradley C Series Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung