Amada AH Series Bedienungsanleitung

Z07M0875E-07

OPERATION MANUAL

WELDING HEAD

AH Series

Thank you for purchasing our Welding Head AH Series.

This operation manual describes its method of operation and precautions for use.

Read this operation manual carefully prior to use. Store appropriately for ready reference.

Contents

1. Special Precautions

(1) Safety Precautions....................................................................... 1

(2) Precautions for Handling.............................................................. 4

2. Features ........................................................................................... 5

3. Installation and Connection

(1) Installation ................................................................................... 6

(2) Connection .................................................................................. 7

4. Operating Method

(1) Stroke and Welding Force Adjustments........................................ 8

(2) Adjustment of Cylinder Descending Speed .................................. 9

(3) Lower Electrode Alignment .......................................................... 10

(4) Adjustment of the Timing to Start a Welding Current Flow............ 10

(5) Pressure Diagram........................................................................ 11

(6) Maintenance Management........................................................... 11

5. Product Specifications

(1) Specifications............................................................................... 12

(2) Welding Cable ............................................................................. 13

6. Outline Drawings ............................................................................. 14

-1-

AH Series

1. Special Precautions

Before using, be sure to read this

operation manual to operate this

machine correctly. This operation

manual may include some items that do

not correspond to your use. However,

you are kindly requested to read only

the items related to your use.

(1) Safety Precautions

These precautions are shown for safe

use of our products and for

prevention of damage or injury to

operators or others. Be sure to read

each of them, since all of them are

important for safety.

The meaning of the words and

symbols is as follows.

！DANGER

Denotes operations and practices that

may imminently result in serious injury

or loss of life if not correctly followed.

！WARNING

Denotes operations and practices that

may result in serious injury or loss of

life if not correctly followed.

Denotes operations and practices

that may result in personal injury or

damage to the equipment if not

correctly followed.

！CAUTION

These symbols denote

“prohibition”.

They are warnings

about actions out of

the scope of the

warranty of the product.

！These symbols denote

actions which

operators must take.

Each symbol represents

the contents that give

notice of DANGER,

WARNING, or

CAUTION to the

operator.

-2-

AH Series

Otherwise, an electric shock or injury will occur. When

internal inspection or repair is required, make contact with us.

Do not disassemble, repair, or modify this machine in

any case.

！DANGER

！

！WARNING

When welding, keep your fingers and hands away from

the electrodes.

Do not put your hands between the electrodes.

The welded part of a workpiece, electrodes and electrode

holder are very hot. Do not touch them; otherwise you may

be burnt.

Do not touch any welded part or electrodes during

welding and just after welding finished.

Application of a voltage out of the specified range can

cause fire and electric shock.

Apply the specified power supply.

Continuous operation after occurrence of a trouble such as

burning smell, abnormal sound, abnormal heat, smoke, etc. can

cause electric shock and fire. If such a trouble occurs,

immediately consult us or your distributor.

Stop the operation if any trouble occurs.

The welding machine generates a magnetic field and has

effects on the operation of the pacemaker while it is turned on.

A person who uses a pacemaker must not approach the

welding machine or walk around the welding shop while the

welding machine is in operation, without being permitted by

his/her doctor.

Persons with pacemakers must stay clear of the welding

machine.

If you look at the surface flash and expulsion directly

during welding, your eyes may be damaged.

Wear protective glasses.

1. Special Precautions

-3-

AH Series

！

！CAUTION

Water splashed over the electric parts can cause electric

shock and short circuits.

Do not splash water on the product.

Do not bend, pull, or pinch any cable forcibly. If the cable is

damaged, it will cause an electric shock, short circuit, or firing.

Do not give excessive force to connecting cables.

Cables of insufficient current-carrying capacities and loose

connections can cause fire and electric shock.

If the welding cable is not connected completely, a spark will occur.

Connect the specified cables securely.

If the product falls or drops, injury may result.

Install the product on firm, level surface.

Do not put any combustible material around the welder. Surface

flash and expulsion can ignite combustible matter.

Keep combustible matter away from the welding machine.

If such a cover is used, it may be overheated and burn.

Do not cover the product with a blanket, cloth, etc.

Keep a fire extinguisher in the welding shop in case of fire.

Keep a fire extinguisher nearby.

Maintain and inspect the product periodically, and repair any

damage near by before starting operation. Tighten the welding

cable connecting section periodically.

Maintain and inspect the product periodically.

Put on protective gear such as protective gloves, long-sleeve

jacket, leather apron, etc. Surface flash and expulsion can burn

the skin if they touch the skin.

Protective gear must be worn.

Use of this product in a manner other than specified can cause

electric shock and fire.

Do not use this product for purposes other than welding.

After a recovery from the outage, the machine may be started or

powered suddenly, resulting in an injury.

When outage occurs, be sure to turn off the power supply.

1. Special Precautions

-4-

(2) Precautions for Handling

Do not install this product in the following:

-Damp places where humidity is higher than 90%,

- Dusty places,

- Places where chemicals are handled,

- Places where corrosive gas is generated,

- Places near a high noise source,

- Hot or cold places where temperatures are above 40C or below 5C, and

- Areas where water will be condensed.

Set the cylinder cover on when operating the cylinder to avoid fingers to be

caught in the cylinder stopper.

In this machine, the linear guide (linear bushing) is used vertically. Accordingly,

grease or oil may drip, but this is not an accident. In particular, when a new

machine is used, lots of grease of oil will drip. In this case, wipe it off properly

during machine operation. If grease or oil sticks on the weldment, this may cause

a defect.

AH Series

Clean the outside of the product with a soft, dry cloth or one wet with a little

water. If it is very dirty, use diluted neutral detergent or alcohol. Do not use paint

thinner, benzine, etc., since they can discolor or deform the product.

Between electrodes, do not put such a material other than the weldment as tool

and screw. Otherwise, the welding electrode will be damaged or a spark will

occur. When performing maintenance for this machine as a result of replacement

of electrodes, turn off the power supplies of the welder and control device in

advance.

Do not put a screw, a coin, etc., in the product, since they can cause a

malfunction.

Be sure to install the screws, which were removed for maintenance of this

machine, in their original positions. If they are installed in different positions, this

machine will be damaged or go wrong.

Operate the product according to the method described in this operation manual.

1. Special Precautions

-5-

AH Series

2. Features

In AH series welding heads, the air cylinder and the pressure follow-up mechanisms are

integrated into signal housing for compact design.

The AH series welding heads offer great quality of welding by improving the accuracy and

reliability, and ease of mounting onto the automatic welding machine.

2. Features

Drill some holes to mount the welding head on the mounting surface of your existing desk,

shelf, or bench as shown below.

Mounting Base Mounting Frame

Note: For installation without a base, the mounting surface must have an enough structural

strength.

-6-

AH Series

3. Installation and Connection

(1) Installation

3. Installation and Connection

ABCDEFGH I J M N

70 180 450 10 160 270 160 145 122 226 For 6-M10 For M10

Center of

electrode

(1) Air Piping

The speed controller with one-touch joint is mounted at the main unit of cylinder. The outer

diameter of urethane tube is φ10.

(2) Connection of the Welding Cable

Connect the bus bar on the rear of the welding head to the welding transformer with a

welding cable of adequate square millimeter.

(3) Connection of the Pressure Signal Cable

Connect the terminal or connector of the pressure signal cable to the welding power supply.

Note: See also the operation manual for the welding power supply.

-7-

AH Series

(2) Connection

3. Installation and Connection

-8-

Home (Released) Touch Press

A = B + C

Full stroke Stroke to touch Stroke to press

AH Series

4. Operating Method

(1) Stroke and Welding Force Adjustments

Rod

Stopper spacer

Cylinder rod

Lock nut

Adjustment nut

Scale

Workpiece

Inhaltsverzeichnis

Andere Amada Schweißsystem Handbücher

Amada

Amada TC-W100A Bedienungsanleitung

Amada

Amada MF-C300A-SF Bedienungsanleitung

Amada

Amada CL-H601A Bedienungsanleitung

Amada

Amada MD Series Bedienungsanleitung

Amada

Amada MH-5B Bedienungsanleitung

Amada

Amada ML-2350A-CE Bedienungsanleitung

Amada

Amada MH-1H-01 Bedienungsanleitung

Amada

Amada HF28/240 Bedienungsanleitung

Amada

Amada ML-2650B Bedienungsanleitung

Amada

Amada Miyachi Unitek STA-200A Bedienungsanleitung

Amada

Amada GS-2 Bedienungsanleitung

Amada

Amada IPB-5000B Bedienungsanleitung

Amada

Amada MEA-100B Bedienungsanleitung

Amada

Amada MA-520B Bedienungsanleitung

Amada

Amada ML-3030AS Bedienungsanleitung

Amada

Amada ML-2350AF Bedienungsanleitung

Amada

Amada ML-2050A-CE Bedienungsanleitung

Amada

Amada UB25 Bedienungsanleitung

Amada

Amada MH-D500D Bedienungsanleitung

Amada

Amada MA-660A Bedienungsanleitung

Amada

Amada 301H/115V Bedienungsanleitung

Amada

Amada Thin-Line TL-080B Series Bedienungsanleitung

Amada

Amada MA-650A Bedienungsanleitung

Amada

Amada TL-180B Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung