American DJ DJ Scan/RG Bedienungsanleitung

User Instructions

American DJ

4295 Charter Street

Los Angeles, CA 90058

www.americandj.com

DJ Scan/RG™ Introduction

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 2

Introduction: Congratulations and thank you for purchasing the DJ

Scan/RG™ by American DJ®, one of the finest pieces of its kind on the

market today! The DJ Scan/RG™ is a great inexpensive, light weight,

intelligent fixture. Due to it’s physical specifications, it’s a great piece

for mobile DJ’s, roller rinks, small clubs, bars, and bowling centers.

When used in multiples of two or more, these units create an effect that

rivals that of units that can cost up to three times the price. The DJ

Scan/RG™ was designed to run in Master/Slave mode but can be used

with any universal DMX-512 controller.

Customer Support: American DJ®provides a toll free customer sup-

port line, to provide set-up and installation help and to answer any

question should you encounter problems during your set up or initial

operation. You may also visit us on the web at www.americandj.com

for any comments or suggestions. Toll free customer service hours are

Monday through Friday 9:00 a.m. to 5:30 p.m. Paciﬁc Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or ﬁre, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®customer support.

Do not discard the shipping carton in the trash. Please recycle when

ever possible.

Improvements and changes in speciﬁcations and design to this

manual and unit may be made at any time without prior notice.

HALOGEN LAMP WARNING!

This fixture is fitted with a halogen lamp which is highly susceptible to

damage if improperly handled. Never touch the lamp with your bare

fingers as the oil from your hands will shorten the lamp life. Never

install, mount, or place this fixture in areas prone to heavy vibration.

Also, never move the fixture until the lamp has had ample time to cool.

Remember, lamps are not covered under warranty conditions.

Revised 8/01

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 4©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 3

DJ Scan/RG™ Quick Start

The DJ Scan/RG™ features a bright 150 watt/500 hour lamp life

halogen bulb with a separate gobo and color wheel. The color wheel

features seven brilliant colors plus white and the gobo wheel features

6 gobos plus a large and small spot. This fixture incorporates the use

of high quality stepper motors for a more accurate mirror movement.

Mirror movement allows for a full 90 degree tilt (vertical) and a 45

degree pan (horizontal). An internal built in microphone allows the

fixtures to run in Stand Alone mode so there is no need for an external

controller. The DJ Scan/RG™ may also be set-up to run in a Master-

Slave mode when used in multiples, up to four units. When used in the

Master-Slave mode, the unit will chase to several internal programs.

The DJ Scan/RG™ can also be controlled via a standard DMX control-

ler such as the American DJ®Show Designer,™ or the American

DJ®DMX Operator,™ giving the user independent control over the

gobo and color wheel as well as the mirrors pan and tilt movements.

Note: The built in programs in the DJ Scan/RG™ are so good you may

never need a DMX controller.

• ZB-JCR/H5 15V/150W, 500 Hour Lamp.

• DMX-512 Compatible.

• Stepper motors for smooth movements.

• 7 colors plus white.

• 7 Gobos plus spot.

• 4 Rotating Gobos, 4 Fixed Gobos.

• 4 Replaceable Gobos (26mm diameter - 22mm viewable)

• Master/Slave Operation

• Sound Active.

• Optional MINI/C controller, for blackout control.

DJ Scan/RG™ Features

Master/Slave Quick Start Stand Alone Mode

Connect up to four units together via XLR cables. The master unit

will run the slaves to the masters built in programs and internal

microphone. Plug in all units. When the DJ Scan/RG™ is first turned

on, it will run through an internal self test where it resets all motors to

their zero position. After the self test the units will react to sound, and

chase to the several built in programs.

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required voltage

for your unit.

• Do not attempt to operate this unit if the power cord has been frayed

or broken. Please route your power cord out of the way of foot trafﬁc.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and ﬁre in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the top cover under any conditions. There are no

user serviceable parts inside.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged in any way.

• Never operate this unit when it’s cover is removed.

• To reduce the risk of electrical shock or ﬁre, do not expose this unit

rain or moisture

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power Cord Protection - Power cords should be routed so they are

not likely to be walked on or pinched by items placed upon or against

them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer.

• Heat -The unit should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

marked change in performance.

DJ Scan/RG™ Safety Precautions

Unpacking:

Every DJ Scan/RG™ has been thoroughly tested and has been shipped

in perfect operating condition, there is no assembly necessary. Carefully

check the shipping carton for damage that may have occurred during

shipping. If the carton appears to be damaged, carefully inspect your

unit for any damage and be sure all equipment necessary to operate

the unit has arrived intact. In case damage has been found or parts are

missing, please contact our toll free customer support number for fur-

ther instructions, please do not return the unit to your dealer.

Power Supply:

Before plugging your unit in be sure the source voltage in your area

matches the required voltage for your American DJ®DJ Scan/RG.™

The American DJ®DJ Scan/RG™is available in a 120v and 220v ver-

sion. Because line voltage may vary from venue to venue, you should

be sure to plug your unit into a matching wall outlet before attempting to

operate you controller.

Data Cable (DMX Cable) Requirements:

Your controller and packs require a standard 3-pin XLR connector for

DMX data input and DMX data output (Figure 1). If you are making your

own cables be sure to use standard two conductor shielded cable (This

cable may be purchased at almost all pro sound and lighting stores).

Your cables should be made with a male and female XLR connector on

either end of the cable. Also remember that DMX cable must be daisy

chained and can not be “Y-d” or split.

Notice: Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX +

DMX -

COMMON

DMX512 IN

CONNECTOR

3 PIN

DMX512 OUT

CONTROLLER

CONNECTOR

3 PIN

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 5

DJ Scan/RG™ Set Up

Figure 2

DJ Scan/RG™ Set Up

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 6

Notice: Be sure to follow ﬁgures two and three when making your own

cables.

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator

on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm

1/4 watt resistor which is connected between pins 2 and 3 of a male

XLR connector (DATA - and DATA +). This unit is inserted in the female

XLR connector of the last unit in your daisy chain to terminate the line.

Using a cable terminator will decrease the possibilities of erratic behav-

ior.

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

Figure 4

1 Ground 1 Ground

XLR Male Socket XLR Pin Conﬁguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

DJ Scan/RG™ DMX Addressing

DMX CHANNEL

123 547986

1 4 16 64 256

2 8 32 128

DMX is short for Digital Multiplex. This is a universal binary language

used as a form of communication between intelligent fixtures. Each dip

switch represents a binary value.

Dip Switch 1 address equals 1

Dip Switch 2 address equals 2

Dip Switch 3 address equals 4

Dip Switch 4 address equals 8

Dip Switch 5 address equals 16

Dip Switch 6 address equals 32

Dip Switch 7 address equals 64

Dip Switch 8 address equals 128

Dip Switch 9 address equals 256

Figure 3

12).

7. Please follow chart on page 12 for all slave dipswitch settings. Note

only one fixture may use the master units dip switch settings (see

Page 12).

8. After all the units settings have been set and are plugged in, adjust

the sensitivity knob on the bottom of the master unit to make them

react to sound.

9. To run a synchronized light show set all the dip switch on all the

fixture to the ‘off’ position. All fixtures will now run in the same

exact pattern.

10. You can also use the optional MINI/C Remote Control. If you want

to use the optional remote control, connect the MINI/C controller

to the first fixture in the line (master).

Note: The remote control only operates in Stand-Alone and Master/

Slave modes. If the remote is connected in DMX mode it will not

function. If the units do not receive an active DMX signal, the

units will automatically react to sound in the Master/Slave mode.

DMX Mode:

This fixture will react with DMX operation. For best results use only

one motor function for each scene (or step), when programming

scenes into a DMX controller. This will give you faster mirror and faster

gobo/color changes. For Example:

A. With DMX controller move the mirror up then program the step.

B. Move the mirror down then program that step.

C. Change the gobo/color wheel then program that step.

D. Continue this pattern to achieve best results.

1. Operating through a DMX controller gives the user freedom to

create his/her own programs tailored to their own individual needs.

This function also allows you to use your fixtures as spots.

2. This operation will allow you to control each individual fixtures traits

with a standard DMX 512 controller such as the American DJ Show

Designer™ or the American DJ®DMX Operator.™

3. The DJ Scan/RG™ uses four DMX channels to operate; Channel 1

is Pan, channel 2 is Tilt, channel 3 is Color, and channel 4 Gobos.

4. To run your fixture in DMX mode, plug in the fixture via the XLR

connections to any standard DMX controller. - Follow the set-up

specifications that come with the controller.

DJ Scan/RG™ Operating Instructions DJ Scan/RG™ Operating Instructions

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 8©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 7

Operating Modes:

You can use the DJ Scan/RG™in three ways:

• Stand alone mode - The unit will react to sound, chasing through

the several built in programs. You can also use the optional DJ

Scan MINI/C Remote Control to blackout the units.

• Master/Slave mode - You can daisy chain up to 4 units together to

get a synchronized light show that will react to sound chasing

through several built in programs.

• DMX control mode - This function will allow you to control each

individual fixtures traits with a standard DMX 512 controller such as

the American DJ Show Designer.™

For best results use fog or special effects smoke to enhance the beams

projections. The DJ Scan/RG™ comes with a protective transportation

cover. Be sure to remove it before attempting any operation!

Stand Alone Mode:

1. To operate as a stand alone unit, via its internal chases and

microphone, turn all dip switches off (see Diagram 1).

2. Adjust the sensitivity knob on the bottom of the unit so the unit

will react to sound.

3. The DJ Scan/RG™ will now react to the bass sound of music via

the internal microphone.

Master-Slave Operation:

1. This function will allow you to link up to 16 units together to run on

the master unit’s 2 channel internal programs.

2. In Master-Slave operation one unit will act as the controlling unit

and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

3. Daisy chain your units via the XLR connector on the bottom

of the units.

4. Use standard XLR microphone cables to link your units together.

Remember that the Male XLR connector is the input and the

Female XLR connector is the output.

5. The first unit in the chain (master) will use the female XLR connec-

tor only - The last unit in the chain will use the male XLR connector

only.

6. Turn all the master units dip switches to the off position (see Page

Due to fog residue, smoke, and dust, cleaning the internal and external

optical lenses must be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside

casing.

2. Use a brush to wipe down the fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days. Situation may very. If used heavily in clubs with lots of

fog, cleaning may be required more often.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the

unit in.

Cleaning frequency depends on the environment in which the fixture

operates (i.e. smoke, fog residue, dust, dew).

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 10©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 9

DJ Scan/RG™ Cleaning

DJ Scan/RG™ Lamp Replacement

Lamp Replacement: Caution! Never open the unit when in use.

Always disconnect the main power before attempting to replace the

lamp.

1. Be sure to follow the proper procedures when handling halogen

bulbs.

2. Lamp replacement has been made simple by incorporating the use

of a removable lamp tray and thumb screws.

3. Loosen the thumb screw on rear cover.

4. Remove the tray.

5. Remove and replace the bulb.

6. Reassemble.

Remember to always replace with the exact same type lamp and

fuse, unless otherwise specified by an authorized American DJ

service technician.

The DJ Scan/RG™ may be controlled by a wide range of controllers;

ie. Show Designer™, DMX Operator,™ Scene Setter™ or by the DJ

MINI/C basic controller.

MINI/C features:

DJ Scan/RG™ Optional Remote

The MINI/C controller may be purchased separately allowing you to

control the main unit, and any others connected to it, while it is in stand

alone mode. You can set the unit to blackout. If you have more than

one unit, make sure the remote control is plugged into the first unit in

the daisy chain. The remote control will not have any effect if the unit

is in DMX mode. When the unit is in blackout mode, the light will come

on next to the blackout button.

30 ft. cable

Stand by (Black out)

Listed below are a few common problems the user may encounter,

with solutions.

No light from the unit;

1. Check if the ‘Power On’ (red) LED is lit and the fan is running. If

not, there is no main power supply.

2. Check the fuse in the back panel.

3. Check if lamp is lit. The user should be able to see some light

escape through the fan. If power is present but the lamp is not lit,

lamp may need to be replaced.

Note: The unit has been designed to shut the lamp down after

60 seconds of inactivity. This is a way of extending lamp life, be

assured this is not a problem with the fixture.

Unit not responding to DMX;

1. If the Green LED on the top of the unit is flashing, the unit is

definitely receiving DMX

2. Check the dip switch settings.

3. If the DMX LED is not lit, check that the DMX cables are connected

properly and are wired correctly (pin 3 is ‘hot’; on some other

DMX devices pin 2 may be ‘hot’). Also, check that all cables are

connected to the right connectors; it does matter which way the

inputs and outputs are connected.

4. If it is a bad connection, the Green LED may flash when cables are

wiggled (but remember it may also be the unit sensing audio!)

5. If DMX connectors are fairly short, ordinary microphone cables

may be used. For longer runs, this may cause data transmission

problems (which will show up as random or incorrect movements)

for best result, use proper balanced data transmission cable.

Unit does not respond to sound;

1. Check to see if the unit is receiving DMX (the green LED should

be off).

2. Tapping the microphone should cause the LED to flash (quiet or

high pitched sounds will not activate the unit). If the red LED

does not flash to sound there may be an internal problem.

3. Be sure the audio sensitivity knob is turn in the full clockwise

position (maximum sensitivity).

Unit blacks out in stand alone mode;

1. Some of the units’ built-in patterns include special effects such

as blackout sweeps.

2. Be sure the audio sensitivity knob is turn in the full clockwise

position (maximum sensitivity).

If problems are not resolved; Contact your American DJ®customer

support for possible service options.

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 12©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 11

DJ Scan/RG™ Trouble Shooting DJ Scan/RG™ Trouble Shooting Cont.

The DJ Scan/RG™carries a one year (365 days) limited warranty. We

recommend you fill out the enclosed warranty card to validate your

purchase. All returned service items whether under warranty or not,

must be freight pre-paid and accompany a return authorization (R.A.)

number. If the unit is under warranty, you must provide a copy of your

proof of purchase invoice. Please contact American DJ®customer

support for a R.A. number.

DJ Scan/RG™ Product Registration

DJ Scan/RG™ Master/Slave Settings

The following details the proper dip switch

setting for Master-Slave operation. Please

follow these setting when running four units

in a Master-Slave conﬁguration.

198765432

198765432 198765432

198765432 198765432 198765432 198765432

Head 2

Head 4

Head 3 Head 15Head 11

Head 14Head 10

Head 9 Head 13

Head 7

Head 6

Head 5

Head 16

Head 12

Head 8

DJ Scan/RG™ DMX Settings

Head 1

ON ON

86 954

371 2

86 954

371 2

86 954

371 2 86 954

371 2

86 954

371 2

DJ Scan/RG™ DMX Traits

©American DJ Supply®- www.americandj.com - DJ Scan/RG™ Instruction Manual Page 14

DMX CHANNEL

12 34

PAN TILT COLOR GOBO

GOBO 7 192-223

GOBO 8 224-255

GOBO 4 96-127

GOBO 1 0-31

GOBO 3 64-95

GOBO 2 32-63

GOBO 5 128-159

GOBO 6 160-191

BLACKOUT 0-28

PURPLE 232-255

PINK 203-231

ORANGE 174-202

YELLOW 145-173

GREEN 116-144

BLUE 87-115

RED 58-86

WHITE 29-67

0˚ 00˚

45˚255

45˚128

90˚255

23˚128

ROTATING

DJ Scan/RG™ Focusing

1. To focus a DJ Scan/RG,™ it is best to first turn down the music

sensitivity knob to its minimum position.

2. Loosen the thumb screw on the front of the unit that hold the lens

in place.

3. Adjust the focus by manually moving the lens up and down.

4. Tighten the thumb screw after you achieve your desired focus.

DJ Scan/RG™ Gobo Layout

big spot

split four

square

bevel

small spot

segment

tunnel

star

bevel

sunrays

diamond

star

Fixed:

Rotating:

American DJ World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 / Fax: 323-582-2610

Web: www.americandj.com / E-mail: [email protected]

DJ Scan/RG™ Warranty Specifications: DJ Scan/RG™

Weight: 13 Lbs.

Dimensions: 18” x 8.6” x 4.3”

Lamp: JCR/H5 15v-150w

Fuse: 120v = 5AGMA

220v = 3AGMA

Voltage*: 120v/220v, 60Hz/50Hz

Gobos: 7 Plus Spot

- 4 Fixed

- 4 Rotating - (Replaceable,

26mm outer diameter -

20mm viewing image)

Colors: 7 Plus White

Cooling: Fan Cooled

Working Position: Any Safe Position

* Operating voltage is preset at the factory.

1-YEAR LIMITED WARRANTY

A. American DJ®hereby warrants, to the original purchaser, American DJ®products to be

free of manufacturing defects in material and workmanship for a period of 1 Year (365 days)

from the date of purchase. This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the owner’s

responsibility to establish the date and place of purchase by acceptable evidence, at the

time service is sought.

B. For warranty service, send the product only to the American DJ®factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ®will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ®shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product

is modiﬁed in any manner which American DJ®concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than the

American DJ®factory unless prior written authorization was issued to purchaser by Ameri-

can DJ®; if the product is damaged because not properly maintained as set forth in the

instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period speciﬁed above, American DJ®will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this warranty

were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ®reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ®in connection with this product, including

warranties of merchantability or ﬁtness, are limited in duration to the warranty period set

forth above. And no warranties, whether expressed or implied, including warranties of mer-

chantability or ﬁtness, shall apply to this product after said period has expired. The con-

sumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ®be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ®Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. All lamps and fuses are not covered under this warranty.

Please Note: Speciﬁcations and improvements in the design of

this unit and this manual are subject to change without any prior

written notice.

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Starball LED DMX Bedienungsanleitung

American DJ

American DJ Progressor 2 Bedienungsanleitung

American DJ

American DJ Micro Star Bedienungsanleitung

American DJ

American DJ Vizi Scan LED PRO Bedienungsanleitung

American DJ

American DJ X-CALIBUR Bedienungsanleitung

American DJ

American DJ Mega Flash DMX Bedienungsanleitung

American DJ

American DJ LTS-1 Bedienungsanleitung

American DJ

American DJ Micro Image RGB Bedienungsanleitung

American DJ

American DJ Color Flash 4 Bedienungsanleitung

American DJ

American DJ UV Panel HP Bedienungsanleitung

American DJ

American DJ Quick Scan Sys Bedienungsanleitung

American DJ

American DJ Crystal Bedienungsanleitung

American DJ

American DJ Fire Bowl Bedienungsanleitung

American DJ

American DJ Torch Light Bedienungsanleitung

American DJ

American DJ Saturn Tri LED Bedienungsanleitung

American DJ

American DJ Spherion WH LED Bedienungsanleitung

American DJ

American DJ Spherion Tri LED Bedienungsanleitung

American DJ

American DJ Spektra 250 Bedienungsanleitung

American DJ

American DJ X-Treme/19C Montageanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ VioMoon LED Bedienungsanleitung

American DJ

American DJ Crusader Bedienungsanleitung

American DJ

American DJ SWEEPER BEAM QUAD LED Bedienungsanleitung

American DJ

American DJ Color-Sphere Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung