Anderson RB580 Bedienungsanleitung

This Quick start up guide does not replace in any way or form the

user manual of this unit.The intension of this document is for use

when setting up the machine after delivery to the dealer and before

the machine is transferred to the end user.This document should

be used as achecklist and memory aid for employees already

familiar with the guidelines in the user manual.Failure to operate

the product correctly can result in damage to the product, personal

property, and cause serious injury.This guide should not be

transferred to the owner of the machine.

QUICK START GUIDE

RB580

After receiving your machine you will want to set it up to be ready for any demo

opportunity or sale that may come along.Besides that, you want to be sure that the

machine is in factory condition, free of damage from transport and defective parts due

to the transport from our factory to your dealership.This is aquick guide that will help

you to be up and ready in ashort time.Before using the machine you must grease and

oil all points on the wrapper that require it.

Basics:

Round bale wrapper

•4 or 5ft bale

•1 stretcher (30’’)

•Bale counter

•Mechanical plastic cut and hold

Note: Before pressure washing the machine be sure to remove the computer (bale counter)

QUICK START GUIDE

RB580

QUICK START GUIDE

RB580

When the machine is to be delivered to the user there are steps you must follow to be sure they are

comfortable with wrapping their first bale. These steps are also important if you are doing a live demo.

Setup is very important to bale size as this machine is not set to a specific bale at the factory.

1) Know your bale size before you start. Asking can help but an actual measurement of

the bale is sometimes necessary.

2) Be sure that everything is greased (if left for more than 3 months outside without use

the machine needs to be fully greased and oiled.

3) Your bale counter is charged and tested operational (see user manual on machine for

functions).

The stretcher pole has 6 positions. Be sure that the position is

not over the height of the bale or under. (this part could have

been removed for shipping so be sure to install correctly for

wrapping bales)

Set the cone roller for 4 or 5 foot

long bale.

Put plastic in the

stretcher. There is only

one way to put the plastic

through. See the diagram

to the left. This is a

sticker found on the

machine as well.

Turn on the bale counter and set.

1) Press the on button

2) You will have to set the counter.To do so you will hold the Adjust Select for 3

seconds.You can then scroll through 4menus with the same button (adjust

select)

3) Use the +and –to change the values of the menu.

4) When wrapping you will hear abuzzer from the counter on the last turn so

that you know when to stop turning the table.The number will automatically

reset once the sequence is finished.

Quick reference for correct plastic layers:

The way that we calculate the amount of plastic to apply on a bale is simple. You wrap the bale manually one

time with only one layer of plastic. You do not want to see any part of the bale when you are finished. You

take the number of turns of the table that it took you to do this and multiply by 2 and add one extra layer (or

turn).

EX: 10 turns to completely cover the bale x 2 = 20. plus one layer = 21. This is the number you want to

program in your bale counter.

QUICK START GUIDE

RB580

Hook the machine to atractor to test it.

Attach the machine hoses to the tractor as

shown.Be sure that your tractor is adjusted

at aflow rate of 8GPM at 2000 PSI.

Once the bale counter is setup you can

start wrapping with the manual lever.

The manual lever can be installed in the

tractor with the extension cable, so you

can operate from the tractor.

QUICK START GUIDE

RB580

The RB580 is equipped with amechanical cut and hold system.The mechanical cut and

hold works on arack and pinion system that stretches alarge spring as the table turns.

The trigger for the release of the system is under the table and is activated as the table

dumps.If the plastic don’t cut or not completely you want to make sure the blade is

sharp and free of rust first.Then you can check if the trigger hit the plate at the right

time and adjust it if need be.

Activated too early Activated at the right time

Fine tuning adjustment

Basic adjustment

Activation plate

QUICK START GUIDE

RB580

The RB580 is equipped with aloading arm that make it possible to load bale directly

onto the bale wrapper without using afrontal loader.The loading arm is sent with

extension cables to control the wrapper from the tractor seat.For loading abale, the

turntable must be parallel to the loading arm. The loading arm is equipped with a

safety device (1) to prevent collisions with the turntable and error operations. The

loading arm must be dropped halfway between the turntable and the ground so that

the table can rotate.Another safety device (2) is installed to insure that the tilting table

is down to be able to lift the arm.

The fork of the arm adjusts to different bale diameter.An adjustable backstop (3)

allows you to charge bales of 4or 5feet wide and filed on the center of the turntable.

When in transport mode you have asafety pin (4) to lock the arm up.

4- Transport mode

Safety pin

3- Bale adjustment

1- Tilting table safety

2- Loading arm safety

Andere Handbücher für RB580

Inhaltsverzeichnis

Andere Anderson Landwirtschaftliche Geräte Handbücher

Anderson

Anderson Fusion720 Bedienungsanleitung

Anderson

Anderson RB580 Bedienungsanleitung

Anderson

Anderson 590HS Bedienungsanleitung

Anderson

Anderson A-INL-032 Bedienungsanleitung

Anderson

Anderson M-160 Bedienungsanleitung

Anderson

Anderson 680HS Bedienungsanleitung

Anderson

Anderson TRB1000 Einrichtungshandbuch

Anderson

Anderson RBM Series Bedienungsanleitung

Anderson

Anderson RBMPRO Einrichtungshandbuch

Anderson

Anderson IFX720 Handbuch

Anderson

Anderson RB-200 Bedienungsanleitung

Anderson

Anderson Hybrid-X Installationsanleitung

Anderson

Anderson RB 680 Bedienungsanleitung

Anderson

Anderson RB-500 Bedienerhandbuch

Anderson

Anderson TSR-3450 Bedienungsanleitung

Anderson

Anderson GB series Bedienungsanleitung

Anderson

Anderson RB-400 Bedienungsanleitung

Anderson

Anderson RB-200 Bedienungsanleitung

Anderson

Anderson ROUND BALE WRAPPER HYBRID Bedienungsanleitung

Anderson

Anderson RBM1400 Bedienungsanleitung

Anderson

Anderson Double stretcher Bedienungsanleitung

Anderson

Anderson STACKPRO Series Einrichtungshandbuch

Anderson

Anderson NWS-660 Bedienungsanleitung

Anderson

Anderson 680HS Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung