Anritsu MP1590B Bedienungsanleitung
Quick Start Guide
MP1590B
Network Performance Tester EoS Measurement
ＥｏＳ測定クイックスタートガイド
CONFIDE
NTIAL 1
Copyright ã2005 by ANRITSU CORPORATION
The contents of this manual shall not be disclosed in any way or
reproduced in any media without the express written permission of
Anritsu Corporation.
1 / 45
MP1590B Network Performance Tester
MP1590B Network Performance Tester
EoS Measurement Quick Start Guide
EoS Measurement Quick Start Guide
Anritsu Corporation
IP Network Div.
First edition
MBP-1SG050233-00
2 / 45
Before using MP1590B
Before using MP1590B
Requisite task before measuring
Put in “Key” and “Remote interlock” at the following circle.
And turn on the key.
In the case of “OFF”, MP1590B cannot transmitted an optical signal.
1
3 / 45
EoS Measurement Flow
EoS Measurement Flow
EoS Measurement Flow
1. Setup
2. Port Setting (Mapping, Type, Bitrate and so on.)
3. Connecting
4. Setting concatenation
5. Measurement
LCAS Test
SDH/SONET Test
VCAT test with Differential Delay
EoS Frame test
6. Other functions
Save/Load
Printing and Screen Copy
Switching between SDH and SONET
4 / 45
¾Put MP1590B on a safe and stable place where
MP1590B is not fallen down on.
¾A cooling fan is situated on the rear panel of the
MP1590B. Place the MP1590B 10 cm or more apart from
obstructions such as walls.
¾Supply power within voltage range of 100 to 115 Vac or
220 to 240 Vac and frequency range of 47.5 to 63 Hz.
Power consumption is 500 Vac or less.
> 10cm
1.
1. Setup
Setup -
-setup
setup
2
5 / 45
MP1590B has two power switches,
“Main power switch”and“Power switch for stand-by condition”.
¾The case of turning on the power
(1) Connect a power code after ensuring that main power switch is Off.
(2) Turn On the main power switch.
(2’) From the Standby condition to power ON, press the power switch for
stand-by condition.
¾The case of turning off the power
(1) Press the power switch for stand-by condition.
(2) Turn off the main power switch.
Power Switch for Stand-by conditionMain Power Switch
1.
1. Setup
Setup -
-Power
Power-
-On/Off procedures
On/Off procedures
6 / 45
1.
1. Setup
Setup -
-Selection of Measuring mode
Selection of Measuring mode
Select the mode of application before measuring.
SDH/SONET/OTN mode is chosen here.
¾SDH/SONET/OTN mode:
For measuring SDH/SONET/OTN, Jitter.
This mode does not support “VCAT” and “LCAS”
¾EoS mode:
For measuring EoS, VCAT, LCAS.
SDH/SONET/OTN mode EoS mode
Button of
changing mode
3
7 / 45
(2) Choose bit rate, encapsulation
(mapping), and concatenation type
Choose the following parameters in pull down
menue:
• Bit rate
• Encapsulation (Mapping)
• Concatenation
2.
2. Port setting (1)
Port setting (1)
Choose bit rate, encapsulation (mapping), and concatenation type
(1) Open Port Setting screen
Right-click the port icon and choose
“Port Setting…” command.
To use the LCAS functions, check this box.
8 / 45
(4)GFP Initial setting
When GFP setting is required, set
• Scramble ON/OFF
• Ethernet Address of this port
• Extension Header parameters
• GFP FCS parameter of Rx side
according to the DUT conditions.
This field changes according to the
selected encapsulation (mapping).
This field is used when it connects to a DUT
requires IP address like router, switch and so
on.
(3) Choose measurement mode and clock modes
(Measurement modes)
Normal mode -- Supports transmitting / receiving data. Select for two-way connection.
Through mode -- Transparent, OH Overwrite and Differential delay are also supported.
Monitor mode -- Not usually used
2.
2. Port setting (2)
Port setting (2)
4
9 / 45
VOA Setting (option) Optical input level
and frequency
3.
3. Connecting
Connecting
Connecting
(1) Connect optical fiber.
¾You have to adjust output optical power using VOA option or external attenuator
before connecting because Tx Laser is always on in EoS mode.
(2) Check the optical input power in Analyze section.
¾You should adjust the optical input power to the optimum value.
¾The optimum value : -10.0 dBm to -12.0 dBm
MU150101A Spec. output power: -1 to +3dBm
input power: -8 to -29 dBm
10 / 45
4.
4. Setting Concatenation
Setting Concatenation -
-Contiguous/Arbitrary
Contiguous/Arbitrary
Setting contiguous concatenation parameters
This setting is available when Concatenation Type is “Contiguous” in port setting.
(1) Multiplexing
Choose “Multiplexing” of measurement
channel in pull down menu. When you
choose “VC4-Xc”, you can set size of
concatenation.
(2) Measurement Channel
Choose “Measurement CH” for both Tx
and Rx side independently.
(3) Dummy Channel
Dummy CH parameters can be set
at the Dummy CH tab, when it is
necessary to set parameters other
than Measurement CH at Tx.
5
11 / 45
Setting virtual concatenation parameters
This setting is available when Concatenation Type is “Virtual” in port setting.
(1) Setting Rx-side VCAT group
At first, it has to match a concatenation and VCAT
group with DUT’s one.
Click “Edit…” button, to set VCG at Rx side.
4.
4. Setting Concatenation
Setting Concatenation -
-Virtual (1)
Virtual (1)
(2) Setting Multiplexing
Next, it has to choose “Multiplexing”. It also has to
choose “Route” when it use Low Order Concatenation.
HO-VCAT LO-VCAT
12 / 45
(3) Detect VCG setting of DUT automatically
Click the “Detect VCG…” button in the Rx VCAT Group Setting screen to show the detected
VCAT group in the Detect VCG screen.
After analyzing, the result screen is appeared. Choose measurement VCG from list window.
And click “OK” button for both Detect VCG and Rx Multiplexing screen.
4.
4. Setting Concatenation
Setting Concatenation -
-Virtual (2)
Virtual (2)
If Rx signal includes some VCG, all VCG
list up in this window.
6
13 / 45
(4-1) Copy Rx setting to Tx side
Click the “Copy from Rx Setting” button to copy Rx setting into Tx side.
4.
4. Setting Concatenation
Setting Concatenation -
-Virtual (3)
Virtual (3)
If a VCG setting in Tx is the same as Rx’s one, see the (4-1);
If a VCG setting is independent between Tx and Rx, see the (4-2);
Finish to set concatenation,
see (5);
Finish to set concatenation,
see (5);
14 / 45
¾Multiplexing:
At first, choose “multiplexing” from pull down menu. If it set
VC3, VC12 or VC11, it also choose “Route” from AU4 or AU3.
¾Choose VCG size and Provisioned size automatically:
VCG members and Provisioned channels can be picked up
automatically when it set in this area. When it chooses
manually, set VCG size to 0 and use the “VCG members”
area.
(4-2) Tx-side VCG setting manually
Click the “Edit…” button to open Tx Multiplexing screen.
4.
4. Setting Concatenation
Setting Concatenation -
-Virtual (4)
Virtual (4)
HO-VCAT LO-VCAT
7
15 / 45
¾Choose VCG members and Provisioned channels
manually:
Click “Add/Remove mode”. And choose channel from this
area. A channel becomes VCG member by “Single Click”
and becomes Provisioned channel by “Double Click”.
4.
4. Setting Concatenation
Setting Concatenation -
-Virtual (5)
Virtual (5)
HO-VCAT LO-VCAT
Finish to set concatenation,
see (5);
Finish to set concatenation,
see (5);
It is possible to change SQ
for each channel in “SQ
Setting mode”.
It is possible to choose
channel across any AUG
by this TAB in LO-VCAT.
16 / 45
(5) Check Linkup
When it completes to set concatenation for both Tx and Rx side, the port icon
becomes green from red. And any alarm/error have gone.
4.
4. Setting Concatenation
Setting Concatenation -
-Virtual (6)
Virtual (6)
Linkup
If an error/alarm occurs,
please check counter to get
detail information,
see 5-(4-1);
8
Andere Handbücher für MP1590B
2
Inhaltsverzeichnis
Andere Anritsu Messgerät Handbücher
Anritsu
Anritsu VectorStar ME7828A Series Bedienungsanleitung
Anritsu
Anritsu S331E Bedienungsanleitung
Anritsu
Anritsu MP1777A Bedienungsanleitung
Anritsu
Anritsu AM-9000 Series Bedienungsanleitung
Anritsu
Anritsu MD1230B Bedienungsanleitung
Anritsu
Anritsu MU182020A Bedienungsanleitung
Anritsu
Anritsu Lightning 37 E Series Bedienungsanleitung
Anritsu
Anritsu Site Master S120A Bedienungsanleitung
Anritsu
Anritsu MW9076 Series Bedienungsanleitung
Anritsu
Anritsu MS2722C Bedienungsanleitung
Anritsu
Anritsu IQ Fiber Master MT2780A Bedienungsanleitung
Anritsu
Anritsu MS2840A Bedienungsanleitung
Anritsu
Anritsu MS2711B Bedienungsanleitung
Anritsu
Anritsu MS2720 A Series Bedienungsanleitung
Anritsu
Anritsu MP1632C Bedienungsanleitung
Anritsu
Anritsu Site Master S331P-0704 Bedienungsanleitung
Anritsu
Anritsu MT8820A Bedienungsanleitung
Anritsu
Anritsu ShockLine MS46322A Series Bedienungsanleitung
Anritsu
Anritsu Network Master MU909020A Bedienungsanleitung
Anritsu
Anritsu LMR Master Bedienungsanleitung
