Anritsu MS27100A Bedienungsanleitung

Configuration Quick Start Guide

Remote Spectrum Monitors

MS27100A, MS27101A, MS27102A, MS27103A

9kHz to 6GHz

1. Introduction

The following are the topics covered in this Quick Start Guide:

•“Setting Up Windows 7 for a Static IP”

•“Configuring for Dynamic IP through SCPI Commands”

•“Setting Up Windows 7 for Dynamic IP”

•“UDP Discovery Tool”

•“Secure Mode”

•“Supplemental Information”

To communicate with the MS2710xA Remote Spectrum Monitor (RSM) or to change its IP

configuration, a PC must be correctly set up to communicate with the instrument via a direct

connection using a static IP. The sections in this guide explain using:

•A Windows PC to directly communicate with the Anritsu spectrum monitor

•SCPI commands for configuring the Ethernet and DNS settings

•The Anritsu Windows network discovery tool to find the instrument IP address

The remote spectrum monitor is shipped with the following default IP configuration:

•DHCP:OFF (Static IP Address)

• Static IP Address: 10.0.0.2

• Static Subnet: 255.255.255.0

• Static Gateway: 10.0.0.0

Read the MS2710xA Product Information, Compliance, and Safety Guide (PN: 10100-00064)

for important safety, legal, and regulatory notices. For additional information and literature

covering your product, visit the product page of your instrument and select the Library tab:

•http://www.anritsu.com/en-US/test-measurement/products/ms27101a

•http://www.anritsu.com/en-US/test-measurement/products/ms27102a

•http://www.anritsu.com/en-US/test-measurement/products/ms27103a

Anritsu Company

490 Jarvis Drive

Morgan Hill, CA 95037-2809

USA

http://www.anritsu.com

Part Number: 10580-00414

Revision: D

Published: June 2019

2. Setting Up Windows 7 for a Static IP

QSG-2 PN: 10580-00414 Rev. D MS2710xA QSG

2. Setting Up Windows 7 for a Static IP

The following example illustrates how to set up Windows 7 for a static IP address. Refer to

your operating system documentation or consult with your network administrator for other

Windows versions or operating systems.

1. Connect an Ethernet crossover cable between the PC and the instrument.

2. Open Control Panel, Network and Internet and select Network and Sharing Center.

3. Select the Local Area Connection link as shown in Figure 1.

Figure 1. Local area connection link

2. Setting Up Windows 7 for a Static IP

MS2710xA QSG PN: 10580-00414 Rev. D QSG-3

4. Select Properties as shown in Figure 2a.

5. Highlight Internet Protocol Version 4 (TCP/IPv4) and select Properties as shown in

Figure 2b.

6. Select Use the following IP address: and enter the following IP properties as shown in

Figure 2c as listed:

• Static IP Address: 10.0.0.2

• Static Subnet: 255.255.255.0

• Static Gateway: 10.0.0.0

7. If you want to specify a domain name system (DNS) server, enter the preferred and

alternate server addresses (Figure 2c). You may need to contact your network

administrator for details about using specific DNS servers; otherwise, select Obtain

DNS server address automatically.

8. Click OK.

The PC is now configured for a direct connection to the instrument using a static IP.

Figure 2. Windows configuration steps

a b c

3. Configuring for Dynamic IP through SCPI Commands

QSG-4 PN: 10580-00414 Rev. D MS2710xA QSG

3. Configuring for Dynamic IP through SCPI Commands

After the PC is properly configured, the connection can be tested. After a good connection has

been confirmed, either SCPI commands or the embedded instrument user interface (UI) may

be used to configure the Ethernet settings on the instrument to different values. Refer to the

embedded Help for details on using the UI.

The following steps describe how to verify and set the Ethernet configuration through SCPI

programming:

1. Using any SCPI client, send the *IDN? query command to 10.0.0.2 on port 9001. Verify

the response includes the model and serial numbers, and other instrument information.

2. To configure the instrument for DHCP, send the following SCPI commands to

10.0.0.2 on port 9001:

SYSTem:COMMunicate:LAN:DHCP?

Queries the DHCP setting. The return value should be OFF if the instrument is

currently configured for static IP.

SYSTem:COMMunicate:LAN:DHCP ON

Turns the DHCP setting ON. The setting is applied immediately upon sending

the command.

3. Disconnect the Ethernet crossover cable between the PC and instrument.

4. Reboot the instrument.

5. Connect the instrument and the controlling PC to your main network with a regular

Ethernet cable. The PC must be re-configured for dynamic IP as described in the next

section.

Caution Consult with your network administrator when configuring the network interface to

avoid potential loss of access or discovery of the device.

Note

If a response is not returned, try switching to a cross-over Ethernet cable and send

the query command again. Ensure that your SCPI client has the termination

character enabled: \n Line Feed (xA).

Note

Turning DHCP ON will change the IP address. The Anritsu Discovery program will

need to be used to retrieve the new IP address. See “UDP Discovery Tool” for

instructions on using the discovery program.

4. Setting Up Windows 7 for Dynamic IP

MS2710xA QSG PN: 10580-00414 Rev. D QSG-5

4. Setting Up Windows 7 for Dynamic IP

1. Select the Local Area Connection link as shown in Figure 3.

2. Select Properties as shown in Figure 4a.

3. Highlight Internet Protocol Version 4 (TCP/IPv4) and select Properties as shown in

Figure 4b.

4. Change the properties to match the illustration as shown in Figure 4c as listed below:

•Obtain an IP address automatically

•Obtain DNS server address automatically

Figure 3. Select the Local Area Connection link

Figure 4. Windows configuration steps

a b c

5. UDP Discovery Tool

QSG-6 PN: 10580-00414 Rev. D MS2710xA QSG

5. UDP Discovery Tool

The UDP Discovery Tool is a Windows application that will display a sortable list of available

MS2710xA devices on the network. This tool provides the ability to find and filter devices by

Hostname, Model number, Serial number, MAC address, Version number, or by IP Address.

If needed, the tool also provides the ability to save the results of your search and to view a

brief history of your searches for comparison.

https://www.anritsu.com/en-US/test-measurement/support

During the download process, a screen will appear as shown in Figure 5.

Figure 5. Installation Directory Default Location

5. UDP Discovery Tool

MS2710xA QSG PN: 10580-00414 Rev. D QSG-7

When the download is complete, a user interface will appear as shown in Figure 6.

Communicating with the RSM

There could be many instruments already connected to the network. Use the selection filter to

narrow the search results.

1. Column Header

2. Column Filter Caret

3. Toolbar

4. Selection Filter List

5. Filter Entry Field

6. Find Instruments Bar

7. Display Type

Figure 6. UDP Discovery Tool User Interface

4 5 6 7

5. UDP Discovery Tool

QSG-8 PN: 10580-00414 Rev. D MS2710xA QSG

Select a filter method

1. Click the connection arrow to display the filter list box are shown in Figure 7.

2. Click a filter method from the list. The selections available are None, Hostname, Model

Number, Serial Number, Mac Address, IP Address, IP Address, and DNS Server.

If a Hostname, Model Number, Serial Number, Mac Address, IP Address, IP Address, or DNS

Server is not known, select None.

•None: All instruments attached to the local area network will be listed.

•Hostname: Host name of the probe

•Model Number: Model Number of the probe

•Serial Number: Serial Number of the probe

•MAC Address: Medium Access Control (MAC) address

•IP Address: Internet Protocol (IP) address

•DNS Server: Domain Name System (DNS) server

Figure 7. Filter List Box

5. UDP Discovery Tool

MS2710xA QSG PN: 10580-00414 Rev. D QSG-9

3. Click None to display an alphabetical listing of the inventoried instruments available to

connect as shown in Figure 8.

Sorting the Listing

Selecting a column header displays a filter caret above column header as shown in Figure 6.

When the caret is clicked, the listing is sorted by the column in the direction the caret is

pointing. Clicking the caret again reverses the caret direction and sorts the listing in reverse

order.

Copy and Paste Example

In this example, refer to the listing in Figure 8.

1. Click serial number 1713003.

2. Copy the serial number.

3. Paste the serial number in the box to the right of the filter list.

4. Click the Find Instruments bar. If the instrument is located, the instrument details will

be displayed as shown in Figure 9.

A status readout is displayed above the column headings. In this example, the readout is:

Filter Type: Serial Number, Filter Value: 1713003, 1 Device(s) Found:

If the device could not be found, the last section would read: No Device Found

Figure 8. Displayed Instrument Inventory

5. UDP Discovery Tool

QSG-10 PN: 10580-00414 Rev. D MS2710xA QSG

Connecting another device will erase the Show Table log and display the new device details.

The previous erased device details will be available in the Show History log until the history

details are erased. See“Clearing the History” on page QSG-12.

Figure 9. Locate Instrument

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Anritsu Messgerät Handbücher

Anritsu

Anritsu MG9637A Bedienungsanleitung

Anritsu

Anritsu LMR Master Bedienungsanleitung

Anritsu

Anritsu 37 C Series Bedienungsanleitung

Anritsu

Anritsu VNA Master MS2024B Bedienungsanleitung

Anritsu

Anritsu MS2690A Installationshandbuch

Anritsu

Anritsu Power Master MA24507A Bedienungsanleitung

Anritsu

Anritsu MP1800A Bedienungsanleitung

Anritsu

Anritsu MS2830A Bedienungsanleitung

Anritsu

Anritsu 54100A Series Montage- und Bedienungsanleitung

Anritsu

Anritsu Site Master S331D Betriebsanleitung

Anritsu

Anritsu MS2711A Bedienungsanleitung

Anritsu

Anritsu MS2690A Bedienungsanleitung

Anritsu

Anritsu Cell Master MT8212B Bedienungsanleitung

Anritsu

Anritsu PIM Master MW8219A Bedienungsanleitung

Anritsu

Anritsu MS2720 A Series Bedienungsanleitung

Anritsu

Anritsu MT1810A Bedienungsanleitung

Anritsu

Anritsu MW9076 Series Bedienungsanleitung

Anritsu

Anritsu IQ Fiber Master Bedienungsanleitung

Anritsu

Anritsu ML2437A Betriebsanleitung

Anritsu

Anritsu 56100A Betriebsanleitung

Anritsu

Anritsu Spectrum Master MS2721B Bedienungsanleitung

Anritsu

Anritsu MP1590B Bedienungsanleitung

Anritsu

Anritsu MS2687B Bedienungsanleitung

Anritsu

Anritsu MD1230B Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung