Anritsu MS2830A Bedienungsanleitung

Document No.: M-W3334AE-32.0

ANRITSU CORPORATION

MS2830A

Signal Analyzer

Operation Manual

Mainframe

Operation

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

32nd Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the

following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of

the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols and

take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MS2830A

Signal Analyzer

Operation Manual Mainframe Operation

15 December 2009 (First Edition)

20 April 2017 (32nd Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

DANGER

●

When replacing the battery, use the specified battery and insert it

with the correct polarity. If the wrong battery is used, or if the battery

is inserted with reversed polarity, there is a risk of explosion causing

severe injury or death.

●

DO NOT expose batteries to heat or fire. This is dangerous and can

result in explosions or fire. Heating batteries may cause them to leak

or explode.

WARNING

●ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the left

may also be used with other marks and descriptions to indicate other

dangers.

●Overvoltage Category

This equipment complies with overvoltage category II defined in IEC

61010. DO NOT connect this equipment to the power supply of

overvoltage category III or IV.

●To ensure that the equipment is grounded, always use the supplied

3-pin power cord, and insert the plug into an outlet with a ground

terminal. If power is supplied without grounding the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

Electric Shock

Replacing Battery

Battery Disposal

For Safety

WARNING

●Only qualified service personnel with a knowledge of electrical fire and

shock hazards should service this equipment. This equipment cannot

be repaired by the operator. DO NOT attempt to remove the

equipment covers or unit covers or to disassemble internal

components. There are high-voltage parts in this equipment

presenting a risk of severe injury or fatal electric shock to untrained

personnel. In addition, there is a risk of damage to precision

components.

●The performance-guarantee seal verifies the integrity of the

equipment. To ensure the continued integrity of the equipment, only

Anritsu service personnel, or service personnel of an Anritsu sales

representative, should break this seal to repair or calibrate the

equipment. Be careful not to break the seal by opening the

equipment or unit covers. If the performance-guarantee seal is

broken by you or a third party, the performance of the equipment

cannot be guaranteed.

Repair

Calibration

For Safety

WARNING

●This equipment should always be positioned in the correct manner. If

the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

●DO NOT short the battery terminals and never attempt to disassemble

the battery or dispose of it in a fire. If the battery is damaged by any of

these actions, the battery fluid may leak. This fluid is poisonous.

DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is

accidentally ingested, spit it out immediately, rinse your mouth with

water and seek medical help. If it enters your eyes accidentally, do

not rub your eyes, rinse them with clean running water and seek

medical help. If the liquid gets on your skin or clothes, wash it off

carefully and thoroughly with clean water.

●This equipment uses a Liquid Crystal Display (LCD). DO NOT subject

the equipment to excessive force or drop it. If the LCD is subjected to

strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested

accidentally, spit it out immediately, rinse your mouth with water and

seek medical help. If it enters your eyes accidentally, do not rub your

eyes, rinse them with clean running water and seek medical help. If

the liquid gets on your skin or clothes, wash it off carefully and

thoroughly with soap and water.

Falling Over

LCD

Battery Fluid

For Safety

CAUTION

●Always remove the main power cable from the power outlet before

cleaning dust around the power supply and fan.

•Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

•Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

●Never input a signal of more than the indicated value between the

measured terminal and ground. Input of an excessive signal may

damage the equipment.

Cleaning

Check Terminal

For Safety

vii

CAUTION

This equipment uses a Poly-carbomonofluoride lithium battery to backup

the memory. This battery must be replaced by service personnel when it

has reached the end of its useful life; contact the Anritsu sales section

or your nearest representative.

Note: The battery used in this equipment has a maximum useful life of

7 years. It should be replaced before this period has elapsed.

This equipment uses USB memory stick as external storage media for

storing data and programs.

If this media is mishandled or becomes faulty, important data may be

lost. It is recommended to periodically back up all important data and

programs to protect them from being lost accidentally.

Anritsu will not be held responsible for lost data.

Pay careful attention to the following points.

●Never remove the USB memory stick from the equipment while it is

being accessed.

●The USB memory stick may be damaged by static electric charges.

●Anritsu has thoroughly tested all external storage media shipped with

this equipment. Users should note that external storage media not

shipped with this equipment may not have been tested by Anritsu, thus

Anritsu cannot guarantee the performance or suitability of such media.

Replacing Memory

Back

-up Battery

External

Storage Media

For Safety

viii

CAUTION

The equipment is equipped with an internal hard disk from which, as

with any hard disk, data may be lost under certain conditions. It is

recommended to periodically back up all important data and programs

to protect them from being lost accidentally.

Anritsu will not be held responsible for lost data.

To reduce the possibility of data loss, particular attention should be

given to the following points.

●The equipment should only be used within the recommend

temperature range, and should not be used in locations where the

temperature may fluctuate suddenly.

●Always follow the guidelines to ensure that the equipment is set up in

the specified manner.

●Always ensure that the fans at the rear and side of the equipment

are not blocked or obstructed in any way.

●Exercise care not to bang or shake the equipment whilst the power is on.

●Never disconnect the mains power at the plug or cut the power at the

breaker with the equipment turned on.

This equipment is designed for an industrial environment.

In a residential environment this equipment may cause radio

interference in which case the user may be required to take adequate

measures.

Exposure to corrosive gases such as hydrogen sulfide, sulfurous acid,

and hydrogen chloride will cause faults and failures.

Note that some organic solvents release corrosive gases.

Hard disk

Use in a

Residential

nvironment

Use in

Corrosive

Atmospheres

Equipment Certificate

Anritsu Corporation certifies that this equipment was tested before shipment

using calibrated measuring instruments with direct traceability to public

testing organizations recognized by national research laboratories, including

the National Institute of Advanced Industrial Science and Technology, and

the National Institute of Information and Communications Technology, and

was found to meet the published specifications.

Anritsu Warranty

Anritsu Corporation will repair this equipment free-of-charge if a malfunction

occurs within one year after shipment due to a manufacturing fault.

However, software fixes will be made in accordance with the separate

Software End-User License Agreement. Moreover, Anritsu Corporation will

deem this warranty void when:

●The fault is outside the scope of the warranty conditions separately

described in the operation manual.

●The fault is due to mishandling, misuse, or unauthorized modification or

repair of the equipment by the customer.

●The fault is due to severe usage clearly exceeding normal usage.

●The fault is due to improper or insufficient maintenance by the customer.

●The fault is due to natural disaster, including fire, wind, flooding,

earthquake, lightning strike, or volcanic ash, etc.

●The fault is due to damage caused by acts of destruction, including civil

disturbance, riot, or war, etc.

●The fault is due to explosion, accident, or breakdown of any other

machinery, facility, or plant, etc.

●The fault is due to use of non-specified peripheral or applied equipment

or parts, or consumables, etc.

●The fault is due to use of a non-specified power supply or in a

non-specified installation location.

●The fault is due to use in unusual environments(Note).

●The fault is due to activities or ingress of living organisms, such as

insects, spiders, fungus, pollen, or seeds.

In addition, this warranty is valid only for the original equipment purchaser. It

is not transferable if the equipment is resold.

Anritsu Corporation shall assume no liability for injury or financial loss of the

customer due to the use of or a failure to be able to use this equipment.

Note:

For the purpose of this Warranty, "unusual environments" means use:

●In places of direct sunlight

●In dusty places

●Outdoors

●In liquids, such as water, oil, or organic solvents, and medical fluids, or

places where these liquids may adhere

●In salty air or in place chemically active gases (sulfur dioxide, hydrogen

sulfide, chlorine, ammonia, nitrogen oxide, or hydrogen chloride etc.) are

present

●In places where high-intensity static electric charges or electromagnetic

fields are present

●In places where abnormal power voltages (high or low) or instantaneous

power failures occur

●In places where condensation occurs

●In the presence of lubricating oil mists

●In places at an altitude of more than 2,000 m

●In the presence of frequent vibration or mechanical shock, such as in

cars, ships, or airplanes

Anritsu Corporation Contact

In the event that this equipment malfunctions, contact an Anritsu Service and

Sales office. Contact information can be found on the last page of the printed

version of this manual, and is available in a separate file on the PDF version.

Andere Handbücher für MS2830A

Inhaltsverzeichnis

Andere Anritsu Messgerät Handbücher

Anritsu

Anritsu VectorStar ME7838E4X Bedienungsanleitung

Anritsu

Anritsu MS2690A Bedienungsanleitung

Anritsu

Anritsu MT8802A Bedienungsanleitung

Anritsu

Anritsu ms2602a Bedienungsanleitung

Anritsu

Anritsu MU181500B Bedienungsanleitung

Anritsu

Anritsu G0430A Bedienungsanleitung

Anritsu

Anritsu Site Master S113BQ Bedienungsanleitung

Anritsu

Anritsu MT8801C Bedienungsanleitung

Anritsu

Anritsu VectorStar ME7838AX Bedienungsanleitung

Anritsu

Anritsu MP1632C Bedienungsanleitung

Anritsu

Anritsu Field Master Pro MS2090A Bedienungsanleitung

Anritsu

Anritsu MP2100A BERTWave Bedienungsanleitung

Anritsu

Anritsu Spectrum Master Bedienungsanleitung

Anritsu

Anritsu MS46122A/B-010 Bedienungsanleitung

Anritsu

Anritsu MT1000A Network Master Pro Bedienungsanleitung

Anritsu

Anritsu ShockLine MS46322A Series Bedienungsanleitung

Anritsu

Anritsu BTS Master Bedienungsanleitung

Anritsu

Anritsu BTS Master MT8220T Betriebsanleitung

Anritsu

Anritsu MS2690A Bedienungsanleitung

Anritsu

Anritsu VectorStar ME7848A Series Bedienungsanleitung

Anritsu

Anritsu MS27100A Bedienungsanleitung

Anritsu

Anritsu MS2690A Installationshandbuch

Anritsu

Anritsu Site Master S113B Bedienungsanleitung

Anritsu

Anritsu VectorStar ME7838G4 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung