Anritsu MS27101A-IBCM Bedienungsanleitung

Anritsu Company

490 Jarvis Drive

Morgan Hill, CA 95037-2809

USA

http://www.anritsu.com

Part Number: 10580-00470

Revision: B

Published: November 2020

Quick Start Guide

MS27101A-IBCM

In-Building Coverage Mapper

MS27101A, 9 kHz to 6 GHz

QSG-2 PN: 10580-00470 Rev. B Mapper QSG

Unauthorized Use or Disclosure

Anritsu Company has prepared the product user documentation for use by Anritsu Company personnel and

customers as a guide for the proper installation, operation, and maintenance of Anritsu Company equipment and

software programs. The drawings, specifications, and information contained therein are the property of Anritsu

Company, and any unauthorized use of these drawings, specifications, and information is prohibited; they shall not be

reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the equipment or software

programs without the prior written consent of Anritsu Company.

Export Management

The Anritsu products identified herein and their respective manuals may require an Export License or approval by

the government of the product country of origin for re-export from your country. Before you export these products or

any of their manuals, please contact Anritsu Company to confirm whether or not these items are export-controlled.

When disposing of export-controlled items, the products and manuals must be broken or shredded to such a degree

that they cannot be unlawfully used for military purposes.

QSG-1 Introduction

Mapper QSG PN: 10580-00470 Rev. B QSG-1

QSG-1 Introduction

The In-Building Coverage Mapper is a portable backpack-contained coverage mapping solution. This Quick

Start Guide provides the following hardware installation and connection topics:

“Unpacking Contents” on page QSG-1

“Equipment Front Panel Interfacing” on page QSG-2

“Inserting Into the SM7009” on page QSG-5

“Ensure the MS27101A and SM7004 fit flush into the SM7009 foam slots as shown in Figure QSG-6.”

on page QSG-5

“Connecting the Hardware” on page QSG-6

Additional Anritsu Documentation

Before proceeding, read the MS27101A Product Information, Compliance, and Safety Guide (PN: 10100-00064)

for important safety, legal, and regulatory notices and refer to the MS2710xA Remote Spectrum Monitor User

Guide (PN:10580-00419), which can be found on the product page:

http://www.anritsu.com/en-US/test-measurement/products/ms27101a

MA8100A TRX NEON® Signal Mapper User Guide (PN:10580-00422) can be found on the product page:

https://www.anritsu.com/en-us/test-measurement/products/ma8100a

For additional information and literature covering your product, go to the products page of your instrument

and select the Library tab here:

https://www.anritsu.com/en-US/test-measurement

Contacting Anritsu

To contact Anritsu, please visit:

https://www.anritsu.com/en-US/contact-us

QSG-2 Unpacking Contents

The components and accessories included in the In-Building Coverage Mapper backpack kit are listed in

Table QSG-1. Remove all components from their boxes and wrapping. Verify that all contents are present.

Table QSG-1. In-Building Coverage Mapper Kit

PartNumber Quantity Item

MS27101A 1 Remote Spectrum Monitor

SM7004 1 Omni Power Bank

SM7005 1 DC Cable

2000-1752-R 1 Wireless Travel Router

2000-1852-R 1 TRX NEON Tracking Unit (Includes USB connection cable and belt clip)

2000-2015-R 1 TRX NEON Tracking Unit (Includes USB connection cable and belt clip)

For Japan end-use orders only

SM7009 1 Foam Enclosure

10580-00470 1 Quick Start Guide

67135 1 Backpack

QSG-3 Equipment Front Panel Interfacing

QSG-2 PN: 10580-00470 Rev. B Mapper QSG

QSG-3 Equipment Front Panel Interfacing

The equipment front panels interfaces are shown below for the:

•MS27101A Remote Spectrum Monitor

•Wireless Travel Router

•SM7004 (Omni Power Pack)

MS27101A Front Panel

The MS27101A is the remote spectrum monitor that performs the signal monitoring. The MS27101A front

panel is shown in Figure QSG-1.

MS27101A Type-N Torque

The antenna Type-N connector types and the recommended torque specs are listed in Table QSG-2.

1. Power Switch

2. Ethernet Port

3. USB Type A Port (2)

4. RF Input Type-N (Torque specs listed in Ta ble Q S G-2 )

5. External Reference Input

6. GPS Antenna Input

Figure QSG-1. MS27101A Front Panel

Table QSG-2.Type-N Connector Torque Setting

Connector Type Torque Setting Recommended Tools

20 GHz, Type-N 1.35 Nꞏ m

12 lbfꞏ in

3/4 in.Torque End Wrench

Twist-On, Type-N

–

Twist-on connector version: Align connectors, thread, and then

twist on until finger tight. Do not use a wrench or pliers to

tighten.

123 4 5 6

QSG-3 Equipment Front Panel Interfacing

Mapper QSG PN: 10580-00470 Rev. B QSG-3

Wireless Travel Router

The wireless travel router is used to interface between the MS27101A and the Android application. The

wireless travel router front panel is shown below in Figure QSG-2.

SM7004 (Omni Power Bank)

The SM7004 is the power source for the MS27101A. The SM7004 front panel is shown in Figure QSG-3.

1. Powered On Indicator LED

2. USB Type A Port

3. Ethernet Port

Figure QSG-2. Wireless Travel Router Front Panel

1. Powered Button/Voltage Selector

2. DC In/Out Jack

3. USB Type A Ports (2)

4. USB Type C Port

5. Battery and Voltage Indicator

Figure QSG-3. SM7004 Front Panel

12 3

123

QSG-4 Setting the SM7004 Voltage

QSG-4 PN: 10580-00470 Rev. B Mapper QSG

QSG-4 Setting the SM7004 Voltage

The SM7004 is the re-chargeable battery bank that provides DC power to the MS27101A. Set the SM7004

voltage to 12 VDC to operate the MS27101A.

To set to 12 VDC:

1. Press and hold the SM7004 power button for two seconds and release. Each of the four SM7004 voltage

indicator LEDs sequence through during the power on. If the four LEDs do not light, the battery is not

fully charged and will need to be charged before continuing.

2. Set the SM7004 to DC output mode by double-pressing the power button.

3. In DC output mode, set to 12 VDC by single-pressing the power button to sequence through each voltage

setting.

4. Set to the 12 VDC position as shown in Figure QSG-4. The voltage output is now set to 12 VDC.

Caution

Do not adjust the SM7004 to 12 VDC when the SM7005 cable is connected to the MS27101A.

Use the steps below to set the SM7004 to 12 VDC before making connection. Damage to the

MS27101A internal circuitry may result if incorrect DC power is applied.

Figure QSG-4. 12 VDC

12 VDC

12 V 16 V 19 V 24 V

QSG-5 Inserting Into the SM7009

Mapper QSG PN: 10580-00470 Rev. B QSG-5

QSG-5 Inserting Into the SM7009

The MS27101A and the SM7004 are assembled into the SM7009 foam enclosure for performing the In-Building

Coverage Mapping as shown in Figure QSG-5.

Ensure the MS27101A and SM7004 fit flush into the SM7009 foam slots as shown in Figure QSG-6.

1. SM7004

2. SM7009

3. MS27101A

Figure QSG-5. MS27101A, SM7004, and SM7009 Assembly

1. SM7009

2. SM7004

3. MS27101A

Figure QSG-6. MS27101A and SM7004 Inserted Into SM7009

QSG-6 Connecting the Hardware

QSG-6 PN: 10580-00470 Rev. B Mapper QSG

QSG-6 Connecting the Hardware

The In-Building Coverage Mapping equipment interface connections are described in this section.

Connect the SM7004

The MS27101A rear panel battery jack is accessible through the foam cutout as shown in Figure QSG-7.

1. MS27101A Rear Panel View

2. SM7009 Rear Panel View

3. MS27101A/SM7009 Rear Panel Battery Input Jack

Figure QSG-7. MS27101A Battery Input Jack

QSG-6 Connecting the Hardware

Mapper QSG PN: 10580-00470 Rev. B QSG-7

1. Connect the SM7005 from the SM7004 to the to the MS27101A rear panel battery input jack.

2. Slightly separate the foam side piece from the main battery foam enclosure to form a groove as shown in

Figure QSG-8.

3. Route the SM7005 through the groove.

4. Insert the entire foam enclosure assembly consisting of the MS27101A, SM7004, and the SM7005 into

the backpack.

1. SM7005

2. Groove

3. Foam Side Piece

4. Main Battery Foam Enclosure

Figure QSG-8. Battery Cable (SM7005) Routing

234

QSG-6 Connecting the Hardware

QSG-8 PN: 10580-00470 Rev. B Mapper QSG

Connecting the Wireless Travel Router

The wireless travel router connects to the MS27101A.

1. Refer to Figure QSG-9.

2. Connect the LAN Ethernet and USB type A cables to the wireless travel router.

3. Connect the wireless travel router USB Type A cable to the USB Type A port on the MS27101A.

4. Connect the wireless travel router LAN Ethernet cable to the Ethernet port on the MS27101A.

Powering On the In-Building Coverage Mapper

1. Disconnect the SM7005 cable from the SM7004 front panel if connected.

2. Set the SM7004 voltage to 12 VDC to operate the MS27101A as described in “Setting the SM7004

Voltage” on page QSG-4.

3. Connect the SM7005 cable to the SM7004 front panel DC In jack.

4. Power on the MS27101A. After a few seconds, the green LED on the wireless travel router will power on.

This confirms that the MS27101A and the wireless travel router are communicating properly. The

In-Building Coverage mapper is now powered on.

1. Wireless Travel Router

2. MS27101A

Figure QSG-9. Ethernet and USB Cable Connection

LAN Ethernet

USB Type A

Inhaltsverzeichnis

Andere Anritsu Messgerät Handbücher

Anritsu

Anritsu MT8820A Bedienungsanleitung

Anritsu

Anritsu SQA-R MP1900A Bedienungsanleitung

Anritsu

Anritsu MS2711A Bedienungsanleitung

Anritsu

Anritsu MS2830A Bedienungsanleitung

Anritsu

Anritsu LMR Master S412E Bedienungsanleitung

Anritsu

Anritsu VectorStar ME7848A Series Bedienungsanleitung

Anritsu

Anritsu Site Master S331P-0704 Bedienungsanleitung

Anritsu

Anritsu Spectrum Master MS2711E Bedienungsanleitung

Anritsu

Anritsu 37 D Series Bedienungsanleitung

Anritsu

Anritsu MS2024A Gebrauchs- und Pflegehandbuch

Anritsu

Anritsu MU104014B Bedienungsanleitung

Anritsu

Anritsu MT8801C Bedienungsanleitung

Anritsu

Anritsu MS2690A Bedienungsanleitung

Anritsu

Anritsu MS2720 A Series Bedienungsanleitung

Anritsu

Anritsu VectorStar ME7838E4 Bedienungsanleitung

Anritsu

Anritsu Spectrum Master MS2711D Bedienungsanleitung

Anritsu

Anritsu Site Master S331C Bedienungsanleitung

Anritsu

Anritsu Site Master S331L Bedienungsanleitung

Anritsu

Anritsu Spectrum Master MS2720T Bedienungsanleitung

Anritsu

Anritsu MS2722C Bedienungsanleitung

Anritsu

Anritsu MS2830A Bedienungsanleitung

Anritsu

Anritsu MW9076 Series Bedienungsanleitung

Anritsu

Anritsu MT8212E Bedienungsanleitung

Anritsu

Anritsu IQproducer XG-PHS Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung