ANTAIRA MSC-204A2 Bedienungsanleitung

Congratulation on your purchasing this high performance PCI

Express multi-serial host adapter. The adapter is high speed PCI

Express bus based and plug-and-play compliant. Its serial ports

are fully 16C950 UART compatible with most of the RS232C

devices available from the market.

Features:



Full x1 PCI Express Throughput, 250Mbytes/sec



Fully Compliant with PCI Express Base Specifications, Revision 1.0a



16C950 UARTs, Fully Compatible with 16C550, Baud Rate up to

115.2Kbps (Optional model for 921.6Kbps available upon request)



Supports 4S RS232 over one single PCI Express slot.



Low Profile PCI Express model available with short bracket



Supports Win98SE, ME, NT, 2000, 2003, 2008, XP, Vista, Win 7and

Linux

4S RS232 Multi Serial PCI Express Card

Installation Guide

1. Introduction

2. Board Layout

J8: DB44 pin

Connector to

4-port Octopus

Cable

J7: Aux. Power

Connector

J2~J5: Internal S1~S4 with

10-pin Header Connectors

JP3: Aux Power

Source Selector

JP2: Power over

Serial Connectors

Enable/Disable

JP1: Parallel Port

Enable/Disable Jumper

(for 4S1P Model Only)

2-Port 422/485 Serial PCI Card

JP2- External Power Enabler: There are 4 jumpers that control the pin-9

signal of the 4 serial port DB9 connectors (S1~S4) respectively. If the

jumper(s) is at the “DIS” position (factory default), the pin-9 was

connected with the RI signal as standard RS232 definition. If the

jumper is at the “PWR” position, the pin-9 was connected with a power

either from PCI Express slot or from Aux Power connector (J7). The

power source is controlled by JP3 jumper (see the following section).

JP3- External Power Selector: The pin-9 of the serial port connector will

be supplied with DC5V or DC12V. There are 3 sources depends on the

jumper’s position of the JP3:

AUX5V: DC5V, from J7, an optional power cable is required.

AUX15V: DC12V, from J7, an optional power cable is required.

PCI12V (factory default): DC12V, from PCI Express golden finger,

no cable is required.

1. Turn the system power OFF before installation!

2. Remove the chassis cover from your computer

3. Locate an unused PCI Express slot (typically white and smaller)

and remove the corresponding slot cover from computer chassis.

4. Plug the I/O card to the unused PCI Express expansion slot and

attached the I/O card bracket to the computer chassis screw.

5. Installing the supplied DB44-to-4XDB9 octopus cable and serial

cables to your serial devices.

6. Put the chassis cover back on the computer.

Note:

PLEASE DO NOT LET WINDOWS AUTO SEARCH THE DRIVERS ON THE CD, it

will cause problems because the INF files will be conflict in this case.

Instead, please browse to the correct location (folder) manually to

make sure the correct drivers are chosen and installed correctly.

3. Jumper Settings

4. Installing the PCI Express I/O Adapter

5. Software Installation

2-Port RS422/485 Serial PCI Card

Note: Windows NT driver Installations

To install the Windows NT driver, please go into WinNT4 sub-directory

and run (double click) Install_Serial.exe to install all Serial Port Drivers.

DB9(Male) on the 9-pin Flat Cable:

Pin#

Signal

Pin#

Signal

DCD

DSR

RXD

RTS

TXD

CTS

DTR

GND

Drivers are in each

corresponding folder

6. Connector Pin Assignments

2-Port 422/485 Serial PCI Card

Inhaltsverzeichnis

Andere ANTAIRA PCI-Karte Handbücher

ANTAIRA

ANTAIRA MSC-102B1L Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-202B1 Bedienungsanleitung

ANTAIRA

ANTAIRA msc-116a Bedienungsanleitung

ANTAIRA

ANTAIRA RS232 Bedienungsanleitung

ANTAIRA

ANTAIRA Dual Channel Gigabit Ethernet PCIe Card Bedienungsanleitung

ANTAIRA

ANTAIRA msc-401a1 Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-204B1 Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-204A1-S Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-102B1-SI Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-102B1 Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-202ALP Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-104B Bedienungsanleitung

ANTAIRA

ANTAIRA RS232 Bedienungsanleitung

ANTAIRA

ANTAIRA msc-216a Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-202A-V2 Bedienungsanleitung

ANTAIRA

ANTAIRA SC-102AL-1 Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-208A Bedienungsanleitung

ANTAIRA

ANTAIRA RS232 Bedienungsanleitung

ANTAIRA

ANTAIRA MSC-202AL Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung