Antari W-515 Bedienungsanleitung

W-515 / W-530

Fog Machine User Manual

English Français Deutsch 中文

‧

‧‧

Page>01 Page>12 Page>24 Page>36

User Manual

W-515 & W-530 Fog Machine

Congratulations on the purchase of your new

ANTARI W-Series FOG MACHINE.

Introduction

Thank you for choosing an ANTARI W-Series Fog Machine. You now own a

rugged and powerful state-of-the-art machine. Prior to use, we suggest that

you carefully read all of the instructions. By following the suggestions found in

this user manual, you can look forward to the reliable and satisfactory

performance of your ANTARI Fog Machine for years to come.

Please follow these operation, safety and maintenance instructions to ensure a

long and safe life for your fog machine.

 

CAUTION:

Risk of electric shock. Disconnect the appliance from the electric supply

before refilling liquid, cleaning or performing maintenance on the

machine.

Danger of Electric Shock

Keep this device dry.

For inside use only. Not designed for outside use.

For all models, use 3-prong grounded electrical outlet only. Prior to use take

care to determine that the unit is installed at the rated voltage.

Always unplug your ANTARI W-Series Fog Machine before filling its tank.

Always keep fog machine in upright position.

Turn off or unplug the machine when not in use.

This machine is not water-proof. If moisture, water, or fog fluid gets inside

the housing, immediately unplug the unit and contact a service technician or

your ANTARI dealer before using it again.

No user serviceable parts inside. Refer to your ANTARI dealer or other

qualified service personnel.

Danger of Burns

This device is for adult use only and must be installed out of the reach of

-01-

children. Never leave the unit running unattended.

Never aim the output nozzle directly at people.

Fog machine output is very hot. Avoid coming within 50 cm of the output

nozzle during operation.

Locate the fog machine in a well-ventilated area. Never cover the unit's vents.

In order to guarantee adequate ventilation, allow a free air space of at least

20 cm around the sides and top of the unit.

Never aim the output nozzle at open flames.

If the supply cord is damaged, it must be replaced by manufacturer or its

service agent or similarly qualified personnel in order to avoid a hazard.

The output nozzle becomes very hot during operation (200°C). Keep

flammable materials at least 50 cm away from the nozzle.

Always allow your ANTARI Fog Machine to cool down before attempting to

clean or service it.

Danger of Explosion

Never add flammable liquids of any kind (such as oil, gas, perfume) to the fog

liquid.

Use only high-quality, water-based fog liquid that your dealer recommends.

Other fog liquids may cause clogging or “spitting”.

Always make sure there is sufficient liquid in the tank. Operating this unit

without liquid might cause damage to the pump as well as over-heating of the

heater.

If your ANTARI W-515 & W-530 Fog Machine fails to work properly,

discontinue use immediately. Drain all fog liquid from the tank, pack the unit

securely (preferably in the original packing material), and return it to your

ANTARI dealer for service.

Always drain tank before mailing or transporting this unit.

Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid

comes in contact with skin or eyes, rinse thoroughly with water.

Note: Pay attention to all warning labels and instructions printed on the

exterior of your ANTARI Fog Machine.

Unpacking & Inspection

Open the shipping carton and verify that all equipment necessary to operate

the system has arrived intact.

The shipping carton should contain the following items:

1.One unit of W-515 or W-530 Fog Machine

2.Power cord

3.One Set of W-1 transmitter

4.User Manual

5.Mounting brackets with washers/screws (optional for W-515)

If any equipment is missing contact your ANTARI dealer immediately.

-02-

Before beginning your initial setup on ANTARI W-515 & W-530 Fog Machine,

make sure that there is no evident damage caused by transportation. In the

event that the unit's housing or cable is damaged, do not plug it in and do not

attempt to use it until after contacting your ANTARI dealer for assistance.

Setup

Remove all packing materials from shipping box. Check that all foam and

plastic padding is removed, especially in the nozzle area.

Place fog machine on a flat surface and remove fog liquid tank cap.

Place the liquid tube into a properly filled liquid tank.

Fill with high-quality, water-based fog liquid recommended by ANTARI dealer.

The W-515 & W-530 only works with uncontaminated Antari FLR or FLG Fog

Liquid. Any other types of liquid can damage the unit resulting in spitting and

serious clogging problem. When filled, place cap back on liquid tank. Be

careful not to exceed the maximum fluid level. DO NOT OVERFILL.

Operation

Control Panel

The built-in control panel on the rear of the machine features an LCD panel

displaying all operation statuses of the fog machine. The control panel allows

the user to customize fog machine functions by adjusting the fogging duration,

interval, and volume as well as the DMX address, the wireless function and the

fluid sensor. There are six buttons on the control board. All current operating

parameters are automatically stored in non-volatile memory, allowing the

machine to be powered down without losing function settings.

After switching on, the display shortly indicates »Antari W-515/W-530«. Then

the fog machine starts with the warm-up process and the display indicates

»Warming Up«. While the unit is warming up, fog output will not be possible

yet. Program the necessary menu settings with the control panel. Once the

warm-up process is completed, fog output will be possible. The display

indicates »Ready to Fog«.

Additionally, a »W« for wireless and an »S« for fluid sensor is indicated if these

functions are activated.

- Configuration of the buttons

FUNCTION

VOLUME

TIMER MANUAL

FUNCTION

TIM ER

VOL UME

MAN UAL

Interval Set

Duration Set

Timer Out

Volume Out

DMX 512 Add

Wireless

Fluid Sensor

2. UP and DOWN

3. TIMER

4. VOLUME

5. MANUAL

-03-

- Menu settings with the button FUNCTION

▪ Setting time intervals for timer operation

Press the button FUNCTION until the display indicates »Interval Set«. Use

the buttons UP and DOWN to adjust the intervals between the individual fog

outputs in timer mode within the range of 1 and 200 seconds.

▪ Setting the output duration for timer operation

Press the button FUNCTION until the display indicates »Duration Set«. Use

the buttons UP and DOWN to adjust the duration of the fog outputs in timer

mode within the range of 1 and 200 seconds.

▪ Setting the fog output volume for timer operation

Press the button FUNCTION until the display indicates »Timer Out«. Use the

buttons UP and DOWN to adjust the fog output volume in timer mode within

the range of 1 % and 100 %.

▪ Setting the fog output volume for continuous operation

Press the button FUNCTION until the display indicates »Volume Out«. Use

the buttons UP and DOWN to adjust the fog output volume in continuous

mode within the range of 1 % and 100 %.

To set the unit to continuous fog output in continuous mode, select »NON

STOP BURST« below a value of 1 % or above a value of 100 %.

NOTE: When setting a fog output volume higher than 30 % for continuous

operation, the fog machine occasionally needs to stop the fog output to

reheat.

When »NON STOP BURST« is selected, the fog machine adjusts the fog

output volume and heater temperature automatically and does not need to

stop the fog output to reheat.

▪ Setting the DMX512 address

Press the FUNCTION until the display indicates »DMX 512 Add.«. Use the

buttons UP and DOWN, to set the machine to the same address as on your

DMX controller. Please refer to chapter DMX512 settings for more

information on DMX operation.

▪ Switching the wireless function on and off

Press the button FUNCTION until the display indicates »Wireless On«. Use

the buttons UP and DOWN to deactivate the wireless function (indication

»Wireless Off«) and to reactivate it (indication »Wireless On«).

▪ Switching the fluid sensor on and off

Press the button FUNCTION until the display indicates »Fluid Sensor On«.

Use the buttons UP and DOWN to deactivate the fluid sensor (indication

»Fluid Sensor Off«) and to reactivate it (indication »Fluid Sensor On«).

- Continuous operation

-04-

Press the button VOLUME, to activate continuous fog output. The display

indicates »Volume« followed by the value that was set in menu item »Volume

Out« or »NON STOP BURST« when continuous fog output was selected. To

stop the fog output, press the button VOLUME once again.

NOTE: When a fog output volume higher then 30 % was set for continuous

operation, the fog machine occasionally needs to stop the fog output to

reheat.

When »NON STOP BURST« was selected, the fog machine adjusts the fog

output volume and heater temeperature automatically and does not need to

stop to reheat.

- Manual operation

For immediate fog output at the maximum volume of fog, keep the button

MANUAL pressed. The display indicates »Manual 100 %«. As soon as you

release the button, the fog output will stop. The manual operation will take

priority over the continuous operation and the timer operation. Even if one of

these operating modes is activated, the fog machine will always emit the

maximum volume of fog when the button MANUAL is pressed.

- Timer operation

In the timer mode, the fog machine will automatically emit fog. The time

intervals, duration and fog volume depend on the corresponding menu

settings. Press the button TIMER, to activate the timer mode. The display

indicates the set time interval. The unit counts down to 0 seconds and emits

fog. To deactivate the timer mode, press the button TIMER again.

W-1 Wireless Remote

The wireless remote control system W-1 consists of a transmitter equipped with

two buttons for fog on and off, and a receiver pre-attached to the rear panel of

each W-series model.

* Transmitter:

With the transmitter it is possible to emit fog via radio over a distance of up to

50 meters. The transmitter is compatible to any receiver of the W-series and

can control an unlimited number of machines in parallel.

-05-

Press the button “A”, to emit fog. The button “A” has the same function as the

button VOLUME on the control panel, i.e. the fog output depends on the

setting of menu item »Volume Out«. The display indicates »Volume« followed

by the defined value or »NON STOP BURST« when continuous fog output was

selected. As additional control, the blue LED light. To stop the fog output,

press the button “B”.

* Receiver:

The receiver is tested and pre-attached to the rear panel of each W-series

model. Please do not try to remove it. The receiver responds to up to 5

different transmitters that are registered with the machine. The included

transmitter has been registered to the machine before shipment. It can be

directly operated without any start-up setting.

- Registering transmitters

To operate the machine with a different transmitter than the included one, or

to operate it with up to 5 different transmitters, each transmitter must be

registered first. For this purpose, turn on the machine. When the display

indicates »Wireless Setup«, press the button “A” 1 second on each

transmitter. Thus the previous transmitters are cleared from the memory of

the receiver. The setting must be completed within 15 seconds after

switching on the machine. Then the machine will automatically exit the

transmitter setting mode. The display shows »Wireless Setup OK«. At this

point, no further transmitter can be added.

If no transmitter is registered when the machine is switched on, the memory

of the receiver will keep the record of the previous operation.

Setting Example 1:

In order to register several transmitters with a machine, turn on the

machine. When the display indicates »Wireless Setup«, press the button “A”

1 second on each transmitter within 15 seconds to establish the signal

transmission.

Setting Example 2:

In order to use 1 transmitter to control 2 or more machines, turn on the

-06-

machines at the same time. When the displays indicate »Wireless Setup«,

press the button “A” 1 second on the transmitter within 15 seconds to

establish the signal transmission.

- Battery change on the transmitter

If the range of the transmitter decreases, the battery is probably exhausted

and must be replaced. For this purpose, take off the housing cover and

remove the used battery. Insert a fresh 12 V battery, type 23A as indicated in

the battery compartment and refit the housing cover.

DMX Connector Pin Assignment

The machine provide 3 or 5 pin XLR connector for DMX connection. Diagram

below indicate pin assignment information

DMX512 Settings

Channel A

0 - 5 = off (no output)

6 - 255 = output volume control (1 - 100 % output)



Both models are equipped with a DMX512 system. For connecting a DMX

controller, 3-pin and 5-pin male-female XLR connections are provided at the

back of each machine. The machines use one control channel for adjusting

the output volume. The channel has a DMX value range of 0 to 255. After

connecting a DMX controller, timer functions such as output duration and

interval can be programmed using the DMX controller or the DMX control

software. The machine cannot be controlled via the built-in control panel nor

the W-1 wireless remote anymore. By using the DMX protocol, fog machines,

lighting effects, and other special effects machines can be interconnected

and easily controlled.

-07-

Pin Function

Ground

Data -

Data +

3 pin XLR5 pin XLR

2 1

35 1

31 5

1 2

Andere Handbücher für W-515

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Antari Nebelmaschine Handbücher

Antari

Antari Z-Stream Bedienungsanleitung

Antari

Antari FT-100 Fire Training Bedienungsanleitung

Antari

Antari Z-1000 III Bedienungsanleitung

Antari

Antari F-450 Bedienungsanleitung

Antari

Antari Onboard DMX Bedienungsanleitung

Antari

Antari B-100 Bedienungsanleitung

Antari

Antari Z-800II Bedienungsanleitung

Antari

Antari B-200 Bedienungsanleitung

Antari

Antari X FOGGER Bedienungsanleitung

Antari

Antari Z-1500II Bedienungsanleitung

Antari

Antari M-1 Bedienungsanleitung

Antari

Antari LCU-1 Bedienungsanleitung

Antari

Antari FT-50 Bedienungsanleitung

Antari

Antari FT-100 Fire Training Bedienungsanleitung

Antari

Antari LCU-2S Bedienungsanleitung

Antari

Antari WiFi-800 Bedienungsanleitung

Antari

Antari WiFi-800 Bedienungsanleitung

Antari

Antari F-6 Bedienungsanleitung

Antari

Antari HZ-100 Bedienungsanleitung

Antari

Antari HZ-500 Bedienungsanleitung

Antari

Antari ICE-100 Bedienungsanleitung

Antari

Antari DNG-200 Bedienungsanleitung

Antari

Antari PM-1 Bedienungsanleitung

Antari

Antari Z-1520 RGB Bedienungsanleitung

Beliebte Nebelmaschine Handbücher anderer Marken

Boost

Boost BOOST-FOG400LED-BK Bedienungsanleitung

Home Accents Holiday

Home Accents Holiday FM1000-ASH Bedienungsanleitung

EuroLite

EuroLite ZEITGEIST FOG-1200 Bedienungsanleitung

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Bedienungsanleitung

PROEL

PROEL DRAGO HEAVY PLFD150HY Bedienungsanleitung

Sparklyn

Sparklyn Y846 Bedienungsanleitung

Magicfx

Magicfx CO2 Gun Bedienungsanleitung

Ibiza

Ibiza LSM500LAS Bedienungsanleitung

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Bedienungsanleitung

High End

High End F-100 Bedienungsanleitung

Chauvet

Chauvet ARENA 2100 FLEX Bedienungsanleitung

Beamz

Beamz F1600 Bedienungsanleitung

Sagitter

Sagitter SG ARS900C Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-STF-480 Bedienungsanleitung

Orion

Orion OT-U250PP Leitfaden

Beamz

Beamz S2500 Bedienungsanleitung

American DJ

American DJ Dyno-Fog II Bedienungsanleitung

JB Systems

JB Systems FX 1700 Bedienungsanleitung