Apera Instruments DO803 Bedienungsanleitung

APERA INSTRUMENTS DO803 Optical Dissolved Oxygen Probe

1. Probe Structure

The instruments DO803 optical dissolved oxygen probe has a cable length of 3m and

built-in temperature sensor for automatic temperature compensation. The electrode

structure is shown in Fig.-6

1. Bottom cover of the calibration sleeve

5. Locking cap

2. Sponge for water storage

6. Optical DO electrode

3. Sensor cap

7. O ring

4. Calibration sleeve

Immersion line:

The tested solution should be above this line

2. Probe Maintenance

The sensor cap of the optical DO electrode must be kept in a moist environment. If the

surface coating of the sensor cap dries out, the measured value will be unstable or the

response will be slow. The electrode calibration sleeve is used to store the probe.

(A) Short-term storage (less than 30 days): The probe head is kept in the calibration

sleeve. Always keep the sponge inside the calibration sleeve wet. Several

drops of clean water should be added to a dry sponge (let the sponge be

saturated, but not dripping), and tighten the lock cap, so that the sensor cap is

kept in the moist-saturated air.

(B) Long-term storage (greater than 30 days): The probe head is kept in the calibration

sleeve. Check whether the water storage sponge is moist every 30 days or user can

store the electrode in a beaker containing water.

Fig.-6

the sponge is dry or if the electrode is exposed to dry air for more than 8 hours, the

surface coating of the sensor cap may be completely dry. So the electrode should

be immersed in tap water at room temperature 25℃for 24 hours. If the water

temperature is low, soaking time is 48-72 hours.

(D) The sponge cannot be allowed to get stained or moldy, otherwise it will consume or

produce oxygen. If stained or moldy, please clean immediately.

3. Sensor Cap

(A) The sensor cap is an important part of the optical DO probe. The surface coating of

the cap cannot be scratched or mechanically worn. Otherwise, the life of the sensor

cap will be reduced or the probe will be damaged. Please pay special attention to it

when using the probe.

(B) The surface coating of the sensor cap cannot withstand high temperatures, so the

optical DO probe cannot be tested in water above 50 ℃.

organic solvents to clean, otherwise it may damage the probe. It can be gently

wiped with a soft cloth or paper towels. To disinfect the probe, immerse it in 3%

hydrogen peroxide for 15 to 30 minutes and then rinse off with water.

(D) The sensor cap has a service life of more than 8000 hours. When the probe is not

being used, it does not "bleach" luminescence layer; in addition, the storage time

will not reduce the life of the probe, so the actual use time of the sensor cap is far

more than a year. The major factor affecting the service life of the sensor cap is the

surface coating being damaged under external force. So the key is to protect the

sensor cap from external damage.

(E) If the sensor cap is damaged or deteriorated, users need to purchase a new one.

Every new cap has a set of calibration codes which need to be input into the

instrument. The specific input method will be described in the instruction manual of

sensor cap.

(F) The probe that comes with the instrument can be used directly without the input of

the calibration codes. So users should not take off the sensor cap when it is not in

use. Nor should one swap the caps from different instruments. When being

installed, the sensor cap must be tightened and the interior cannot be contaminated

or wet.

Limited Warranty

We warrant this DO803 optical DO probe (excluding sensor cap) to be free

from defects in material and workmanship and agrees to repair or replace

free of charge, at option of APERA INSTRUMENTS (Europe) GmbH, any

malfunctioned or damaged product attributable to responsibility of APERA

INSTRUMENTS (Europe) GmbH for a period of Two Years ( 1 year for

DO8032 sensor cap) from the delivery.

This limited warranty does not cover any damages due to:

i. transportation;

ii. storage;

iii. improper use;

iv. failure to follow the product instructions or to perform any preventive

maintenance;

v. modifications;

vi. combination or use with any products, materials, processes, systems

or other matter not provided or authorized in writing by us;

vii. unauthorized repair;

viii. normal wear and tear; or

ix. external causes such as accidents, abuse, or other actions or events

beyond our reasonable control.

APERA INSTRUMENTS (Europe) GmbH

Wilhelm-Muthmann-Straße 15

42329 Wuppertal, Germany

Email: [email protected]

Website: www.aperainst.de

Tel.: +49 202 51988998

Inhaltsverzeichnis

Andere Apera Instruments Messgerät Handbücher

Apera Instruments

Apera Instruments Gro Star AI102G Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 851-H Bedienungsanleitung

Apera Instruments

Apera Instruments SX731 Bedienungsanleitung

Apera Instruments

Apera Instruments YD300 Bedienungsanleitung

Apera Instruments

Apera Instruments 950 Series Bedienungsanleitung

Apera Instruments

Apera Instruments Premium Series Bedienungsanleitung

Apera Instruments

Apera Instruments PH 8500 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 763 Bedienungsanleitung

Apera Instruments

Apera Instruments EC400 Bedienungsanleitung

Apera Instruments

Apera Instruments PH60Z-PW Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 753 Bedienungsanleitung

Apera Instruments

Apera Instruments TN420 Bedienungsanleitung

Apera Instruments

Apera Instruments LabSen 751 Bedienungsanleitung

Apera Instruments

Apera Instruments PH850 Bedienungsanleitung

Apera Instruments

Apera Instruments PH60Z-MS Bedienungsanleitung

Apera Instruments

Apera Instruments SX811-PW Bedienungsanleitung

Apera Instruments

Apera Instruments YD300 Gebrauchsanweisung

Apera Instruments

Apera Instruments LabSen 823 Bedienungsanleitung

Apera Instruments

Apera Instruments YD300 Bedienungsanleitung

Apera Instruments

Apera Instruments PHB-3 Bedienungsanleitung

Apera Instruments

Apera Instruments WS200 Bedienungsanleitung

Apera Instruments

Apera Instruments 2310T-F Bedienungsanleitung

Apera Instruments

Apera Instruments GroStar AI101G Bedienungsanleitung

Apera Instruments

Apera Instruments SX811-BS Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung