Areca ARC-5020-3 Bedienungsanleitung
Areca ARC-5020-3 Card Installation
for MAC Pro Systems
v1.0
ARC-5020-3 Installation instructions for MacPro
1. Turn off / Shut Down your computer
Touch the metal on the outside of your MAC Pro
(Chassis) while it’s still plugged in to discharge any
static electricity from your body.
Then Turn off the
system. When the system is completely shut down,
unplug the power cord of the Mac Pro.
2. Open the Mac Pro Case
Lift the rear latch to unlock the side panel.
Caution - The internal components can still
be very hot after the system has been shut down.
Allow the system to cool down if needed.
Open side panel by pulling away from the case,
then lift up to remove. Set side panel aside.
3. Remove the drive carriers
Make sure the latch on the back panel is still open, then pull out
empty drive carriers 2, 3 and 4 and set them aside.
NEXT PAGE 1
ARC-5020-3 Installation instructions for MacPro
5. Install the Areca ARC-5020-3 Card
The ARC-5020-3 has a cable and a card end.
Install the cable end into Drive Port 2 on
the motherboard. Then slide the card end into
the slot where the PCI bracket was removed.
Make sure the cable connector is securely into
the SATA port on the motherboard and the
card is fully seated into the slot.
6. Replace the PCI Bracket
Make sure the cable connector is securely
fit into the SATA port on the motherboard
and the card is fully seated into the slot.
Take the PCI bracket and re-insert to its
original location, then tighted both screws.
The PCI bracket will hold the ARC-5030-3
card in place.
4. Locate and Remove the PCI bracket
The PCI bracket will have two thumbscrews.
Loosen both thumbscrews until PCI bracket
can be easily removed. Remove the bracket
and the port access cover to allow room for
the ARC-5030-3 card to be installed.
NEXT
PAGE 2
Drive
Port 2
Drive
Port 4
Drive
Port 3
ARC-5020-3 Installation instructions for MacPro
8. Insert side panel and close the latch
Slide side panel down and toward case. Close
latch and reconnect the external cables and the
power cord.
9. Connecting ARC-5020 RAID Box
After the ARC-5020-3 card is installed in the Mac Pro. you are
now ready to connect the ARC-5020 RAID Box to the Mac by
using the e-SATA cable provided.
Note:
If you have not installed the drives or setup the RAID set
and volume, please refer to section 2.2 Installation on the
users manual for proper drive installation and configuring
the RAID before connecting to your MAC Pro host computer.
7. Insert the empty drive carriers
Make sure the rear latch is still up, and then slide
in all the empty drive carriers back in order.
PAGE 3
Andere Areca PCI-Karte Handbücher
Beliebte PCI-Karte Handbücher anderer Marken
Conrad Electronic
Conrad Electronic 97 46 71 Bedienungsanleitung
Micro Innovations
Micro Innovations USB650A Bedienungsanleitung
KTI Networks
KTI Networks KF-310 Bedienungsanleitung
Asus
Asus SpaceLink WL230 Bedienungsanleitung
SIIG
SIIG SC2475 Bedienungsanleitung
TRENDnet
TRENDnet TEW-703PI Bedienungsanleitung
Belkin
Belkin F5D7000F Bedienungsanleitung
Pericom
Pericom PI7C7100 Bedienungsanleitung
ADLINK Technology
ADLINK Technology cPCI-3548 Bedienungsanleitung
Digium
Digium TE200 Series Bedienungsanleitung
Allo.com
Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung
Western Digital
Western Digital FireWire PCI Adapter Bedienungsanleitung