Argos Camden 264/9971 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 79.5cm

Depth - 49.5cm

Height - 183.5cm

Camden - 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 24/03/14

Important - Please read these instructions fully before starting assembly

Ruler - Use this ruler to help correctly identify the screws

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

266/1021

264/9971

ALR2982

Step 9

Warning: The

robe is heavy.

Lift with care.

Fit the back panel

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

b: Place the back

onto the unit, coloured

surface facing down.

Note: The back must be

positioned so that it is

central on the unit.

Nail around the

outside edges of the

back .

Note: Nails should try to

be spaced out evenly.

Stand the unit up for

the next stage.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

The back must be

positioned central on the unit

- same gap on each side

Misaki 2 Door Robe

Due to continuous improvements to our products, please follow the

instructions below for fitting the back panel.

Issue 2 - 12/12/12 - Assembly method changed - Top is now fitted before the Left Side has been fitted.

Issue 3 - 12/12/13 - Extra Cat code added.

Issue 4 - 24/03/14 - New Cat codes.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 45kgs. Please lift

with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

1 2

80%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Base (D2006A)

(722 x 473mm)

Door (D2008A)

(1700 x 358mm) x 2

Plinth (D1994A)

(722 x 96mm)

Hanging Rail (FHR715)

(715mm long)

8Back (X733)

(1713 X 740mm)

Left Side (D2004A)

(1800 x 491mm)

Top (D2003A)

(796 x 492mm)

Right Side (D2005A)

(1800 x 491mm)

Back Rail (D2007A)

(722 x 130mm)

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Rule

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Tools required

Rule

ScissorsSquare

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Step

ladder

Ruler - Use this ruler to help correctly identify the screws

Electric drill

(only use

when drilling

into walls)

B C

D E F

G H I

Nail (F51) x 32

Hinge plate

(F523) x 6

Rail Holder

(F891) x 2 13mm Screw (F63) x 16

Hollow core

locking nut

(F892) x 4

Small metal dowel

(F893) x 4

19mm Screw (F461) x 4

Metal dowel (F901) x 8

Large locking

nut (F900) x 8

Hinge (F522) x 6

Wooden dowel (F22) x 6

Handle (F309) x 2

J K

Bracket (F327) x 1

13mm Screw (F79) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the left side

a: Fit 3 hinge plates

onto the left side ,

making sure that the slot

is facing towards the

finished front edge.

b: To fit the rail holder

. , screw through the

top hole with screw

and into the mark hole

drilled in the left side .

Make sure that it is fitted

straight, in line with the

panel edges and then fit

another screw using

the lower hole.

c: Push 2 hollow core

locking nuts into the

left side , making sure

that they are flush

against the panel’s

surface.

Using a hammer, tap in

the pin on the hollow

core locking nut .

Note: The pin should be

tapped in flush with the

top surface of the hollow

core locking nut .

d: Screw 4 metal

dowels into the holes

on the left side .

Note: Tighten metal

dowels up fully against

the panel.

80%

Finished

front edge

B B

Assembly Instructions

Step 2

Finished

front edge

Finished

front edge

B B

1 1 1

B B

Prepare the right side

a: Fit 3 hinge plates

onto the right side ,

making sure that the slot

is facing towards the

finished front edge.

b: To fit the rail holder

. , screw through the

top hole with screw

and into the mark hole

drilled in the right side

. . Make sure that it is

fitted straight, in line with

the panel edges and

then fit another screw

using the lower hole.

c: Push 2 hollow core

locking nuts into the

right side , making

sure that they are flush

against the panel’s

surface.

Using a hammer, tap in

the pin on the hollow

core locking nut .

Note: The pin should be

tapped in flush with the

top surface of the hollow

core locking nut .

d: Screw 4 metal

dowels into the holes

on the right side .

Note: Tighten metal

dowels up fully against

the panel.

Finished

front edge

Finished

front edge

Assembly Instructions

Step 3

Prepare the base

Insert 4 large locking

nuts into the base .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Tap 2 wooden dowels

into the base .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

10mm

Fit the base to the

right side

Push the base onto

the right side .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Step 4

Step 5

Prepare the top

Screw 4 small metal

dowels into the holes

on the top .

Note: Tighten metal

dowels up fully against

the panel.

Assembly Instructions

Step 6

Prepare the plinth and

the back rail

Insert 2 large locking

nuts into the plinth

and 2 into the back rail

. .

Tap 2 wooden dowels

into the plinth and 2

into the back rail .

Step 6

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the base plinth

and back rail .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

B B

Fit top

Attach the top onto

the assembly.

Note: You will need to

slide the 4 small metal

dowels into the top

of the 4 hollow core

locking nuts .

Insert a screwdriver into

the 4 hollow core locking

nuts and turn the nuts

inside as far as they will

go.

B B

Fit the top

Attach the top onto

the assembly.

Note: You will need to

slide the 2 small metal

dowels into the top

of the 2 hollow core

locking nuts .

Insert a screwdriver into

the 2 hollow core locking

nuts and turn the nuts

inside as far as they will

go.

Step 7

Assembly Instructions

Step 8

Step 9

B B

Fit the left side

Push the left side

onto the assembly.

Note: You will need to

slide the 2 small metal

dowels into the top

of the 2 hollow core

locking nuts .

Insert a screwdriver into

the 2 hollow core locking

nuts and turn the nuts

inside as far as they will

go.

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the base , plinth

and back rail .

Fit the plinth and the

back rail

Push the plinth and

the back rail onto

the right side .

Use a screwdriver to

tighten the 2 large

locking nuts fitted to

the plinth and back

rail .

Note: Support the end

of the plinth and

back rail until the left

side has been fitted.

Assembly Instructions

Step 10

Warning: The

robe is heavy.

Lift with care.

Fit the back panel

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

b: Place the back

onto the unit, coloured

surface facing down.

Note: The back must be

positioned so that it is

central on the unit.

Nail around the

outside edges of the

back .

Note: Nails should try to

be spaced out evenly.

Stand the unit up for

the next stage.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos SKYE WOOD 476/7538 Bedienungsanleitung

Argos

Argos Washington 02BS Bedienungsanleitung

Argos

Argos Mendoza 330/9430 Bedienungsanleitung

Argos

Argos Napoli 600/6259 Bedienungsanleitung

Argos

Argos REAGAN FAB LH CRN CHAISE SOFABED CHARCOAL... Bedienungsanleitung

Argos

Argos CANVAS 214/6601 Bedienungsanleitung

Argos

Argos Austen 804/3416 Bedienungsanleitung

Argos

Argos 875/4334 Bedienungsanleitung

Argos

Argos Cheval 147/2204 Bedienungsanleitung

Argos

Argos 497/1630 Bedienungsanleitung

Argos

Argos Silbury 4184719 Bedienungsanleitung

Argos

Argos Tolga 414/5758 Bedienungsanleitung

Argos

Argos Puerto Rico 368/9277 Bedienungsanleitung

Argos

Argos Samuel Shorty Bunk Bed Bedienungsanleitung

Argos

Argos Yanniek 483/4124 Bedienungsanleitung

Argos

Argos Maximus 606/5472 Bedienungsanleitung

Argos

Argos Venice Entertainment Unit Bedienungsanleitung

Argos

Argos 609/0117 Bedienungsanleitung

Argos

Argos Cheval 152/6882 Bedienungsanleitung

Argos

Argos Emmett 149/2765 Bedienungsanleitung

Argos

Argos Swanley 120 307/0013 Bedienungsanleitung

Argos

Argos Dutch Glam Boutique Coffee Table Bedienungsanleitung

Argos

Argos 600/5580 Bedienungsanleitung

Argos

Argos Athina 608/0804 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung