Argos Capella 615/6831 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Capella - 3 Door Mirror Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 3 - 16/05/12

Important - Please read these instructions fully before starting assembly

615/6831

615/6848

615/5997

615/6855

ALR2603

Width - 115cm

Depth - 49cm

Height - 181cm

Issue 2 28/7/11 Change size of robe rail from 723 to 722mm and code to FHR722

Issue 3 - 16/05/12 - New Argos Code added

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 75kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

80%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

1Left Side (D1013A)

(1808 x 490mm)

2Right Side (D1014A)

(1808 x 490mm)

Top/Base (D1018A)

(1119 x 471mm) x 2

Plinth (D1024A)

(1119 x 85mm)

8Standard Door (D1017A)

(1701 x 369mm) x 2

7Loose Shelf (D1023A)

(369.5 x 469mm) x 3

Long Divider (D1021A)

(1685 x 470mm)

1110 Small Back (X831A)

(1711 x 392mm)

Large Back (X830A)

(1711 x 753mm)

Hanging Rail (FHR722)

(722mm long)

Mirror Door (D1017MA)

(1701 x 369mm) x 1

(Mirror - SG13 - 1696 x 311mm

4mm Safety Back SAR)

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 10

Metal dowel (F901) x 10

D E

Large locking

nut (F900) x 10

G H I

Nail (F51) x 40

see malibu fitment mk2 for large number of panels and fittings

25mm Screw (F50) x 6 13mm Screw (F79) x 11

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

13mm Screw (F63) x 18

Rail holder

(F1014) x 2

Shelf stud (F110) x 12

Handle (F930) x 3

Bracket (F327) x 1

Hinge (F522) x 6

40mm Screw (F910) x 4

Important: The hinge

plates used in this

step are in the bag

marked as AHP1546.

AHP1546

AHP1043

Important: The hinge

plates used in this

step are in the bag

marked as AHP1043.

AHP1043

AHP1546

Hinge (F518) x 3

Hinge plate

(F523) x 9

Tools required

Rule

Scissors

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Step

ladder

Electric drill

(only use

when drilling

into walls)

Square

mm 10 20 30 40 50 60 70 80 90 100

Finished

front edge

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the long

divider

Only carry out this step

if you have chosen to

fit the shelves on the

right side.

Fit 3 hinge plates onto

the long divider ,

making sure that the slot

is facing towards the

finished front edge.

Push a rail holder into

the long divider .

Make sure that it is fitted

straight, in line with the

panel edges.

Step 2

Prepare the long

divider

Only carry out this step

if you have chosen to

fit the shelves on the

left side.

Fit 3 hinge plates onto

the long divider ,

making sure that the slot

is facing towards the

finished front edge.

Push a rail holder into

the long divider .

Make sure that it is fitted

straight, in line with the

panel edges.

Step 3

Choose which side

you would like the

shelves Shelves on

the right side

Shelves on

the left side

Finished

front edge

Assembly Instructions

Step 4

Step 5

Prepare the top and

base

Tap 4 wooden dowels

into the top and base

. as shown.

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Insert 4 large locking

nuts into the top

and base as shown.

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

10mm

Finished

front edge

x 2 D

DImportant: If one of the top/base

panels has a plain chipboard surface

this must be used as the base.

Finished

front edge

Finished

front edge

Finished

front edge

Fit top and base to

the long divider

Only carry out this step

if you have chosen to

fit the shelves on the

right side.

Attach the top to the

long divider using 2

screws .

Attach the

base to

the long

divider

using 2

screws .

Important: If one of the top/base

panels has a plain chipboard surface

this must be used as the base.

Finished

front edge

Finished

front edge

Assembly Instructions

Step 6

Step 7

Prepare the plinth

Tap 2 wooden dowels

into the plinth .

Insert 2 large locking

nuts into the plinth

. .

Plain chipboard

surface

Step 6

Finished

front edge

Fit top and base to

the long divider

Only carry out this step

if you have chosen to

fit the shelves on the

left side.

Attach the

top to the

long divider

using 2

screws .

Attach the

base to the

long divider

using 2 screws .

Important: If one of the

top/base panels has a plain

chipboard surface this

must be used as the base.

Profiled

front edge

Prepare the right side

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Screw 5 metal dowels

into the right side .

Note: Tighten the metal

dowels up fully against

the panels.

Refer to step 1 and, only

if you have chosen to

put the shelves on the

left side, push a rail

holder into the right

side . Make sure that

it is fitted straight, in line

with the panel edges.

Shelves on

the right side

Shelves on

the left side

Prepare the left side

Refer to step 1 and, if

required, fit 2 hinge

plates onto the left

side , making sure

that they face the same

way as the diagram.

Insert 2 large locking

nuts into the left side

. as shown.

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Assembly Instructions

Step 8

Step 9

Profiled

front edge

Prepare the left side

Fit 3 hinge plates onto

the left side , making

sure that the slot is

facing towards the

finished front edge.

Screw 5 metal dowels

into the left side .

Note: Tighten the metal

dowels up fully against

the panels.

Refer to step 1 and, only

if you have chosen to

put the shelves on the

right side, push a rail

holder into the left

side . Make sure that

it is fitted straight, in line

with the panel edges.

Profiled

front edge

of right side

Fit the right side

Push the right side

onto the top and

base as shown.

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the top and base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

4 4

Note: From now on the

diagrams show the long

divider on the right side

of the unit. You may have

fitted it to the left side.

Assembly Instructions

Step 10

Finished

front edge

Fit the left side

Push the left side

onto the top , base

and plinth .

Use a screwdriver to

tighten the 5 large

locking nuts fitted to

the top , base and

plinth .

4 4

Step 12

Fit the left side

Push the left side

onto the top , base

and plinth .

Use a screwdriver to

tighten the 5 large

locking nuts fitted to

the top , base and

plinth .

Step 11

4 4

Prepare the plinth

Tap 2 wooden dowels

into the plinth .

Insert 2 large locking

nuts into the plinth

. .

Plain chipboard

surface

Fit the plinth

Push the plinth onto

the right side .

Use a

screwdriver to

tighten the

large locking

nut fitted to

the plinth .

Note: Support the plinth

until the left side has been

fitted in the next step.

Assembly Instructions

Step 13

Fit the back panels

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

b: Place the small back

. and large back

coloured surface facing

down, onto the unit as

shown.

Make sure that the 2

backs and are

pushed up tight against

each other and that they

meet in the centre of the

long divider’s back

edge.

Nail around the

outside edges of the 2

backs and .

Note: Do not nail where

the 2 backs meet.

Nails should be spaced

out evenly.

c: Using 10 screws ,

screw down between the

2 backs and into

the long divider’s

back edge.

Stand the unit up for

the next step.

10 11

Warning: The

unit is heavy.

Lift with care.

Note: Only use 10 screws .

You will need 1 for a later step.

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

Impotant: If you have fitted the long divider on the left side of the

unit the backs will need to go the opposite way around i.e. the

small back on the left side and the large back on the right side.

Left side

Right side

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Woburn 186/2807 Bedienungsanleitung

Argos

Argos Dalton 228/5713 Bedienungsanleitung

Argos

Argos Winchester 656/7004 Bedienungsanleitung

Argos

Argos Hallingford 305/2811 Bedienungsanleitung

Argos

Argos Camden 305/0772 Bedienungsanleitung

Argos

Argos Ellie 244/7472 Bedienungsanleitung

Argos

Argos HOME Bedienungsanleitung

Argos

Argos SAVANNA 476/9086 Bedienungsanleitung

Argos

Argos Atlas Internal Cube 339/5176 Bedienungsanleitung

Argos

Argos 875/4664 Bedienungsanleitung

Argos

Argos Hygena 614/0744 Bedienungsanleitung

Argos

Argos Alicia 188/8379 Bedienungsanleitung

Argos

Argos 609/6269 Bedienungsanleitung

Argos

Argos 903/6240 Bedienungsanleitung

Argos

Argos Ohio 6+2 Sideboard 314/7128 Bedienungsanleitung

Argos

Argos SAN DIEGO 412/2214 Bedienungsanleitung

Argos

Argos 389/6400 Bedienungsanleitung

Argos

Argos Rattan 4 Piece Sofa Set 502/2636 Bedienungsanleitung

Argos

Argos 833/2536 Bedienungsanleitung

Argos

Argos Cheval 147/5634 Bedienungsanleitung

Argos

Argos HOME 631/1494 Bedienungsanleitung

Argos

Argos 7592573 Bedienungsanleitung

Argos

Argos BRADLEY 2581747 Bedienungsanleitung

Argos

Argos Chicago Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung