Argos Capella Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 83cm

Depth - 49cm

Height - 181cm

Capella - 1 Drawer 2 Door Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 1 - 03/12/14

Important - Please read these instructions fully before starting assembly

343/7711

356/6589

339/5200

ALR3121

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 50kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Tools required

Rule

Scissors

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Step

ladder

Electric drill

(only use

when drilling

into walls)

Square

mm 10 20 30 40 50 60 70 80 90 100

Components - Panels

Please check you have all the panels listed below

80% x 2

90% x 1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (DF1997A)

(1808 x 490mm)

2Right Side (DF1998A)

(1808 x 490mm)

Door (DF1860A)

(1541 x 394mm) x 2

12 Back (X1711-823A)

(1711 x 823mm)

Hanging Rail (FHR787)

(787mm long)

Plinth (DF1999A)

(797 x 85mm)

Top (DF1995A)

(797 x 471mm)

Drawer Front (DF1800B)

(793 x 157mm)

Drawer Back

(W765-124BK)

(765 x 124mm)

Drawer Base (T776-367)

776 x 367mm)

Left Drawer Side

(W370-124LH)

(370 x 124mm)

Right Drawer Side

(W370-124RH)

(370 x 124mm)

Base (DF1996A)

(797 x 471mm) x 2

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 14

Metal dowel (F901) x 16

D E

Large locking

nut (F900) x 14

G H I

Nail (F51) x 32

see malibu fitment mk2 for large number of panels and fittings

Rail holder

(F1014) x 2

25mm Screw (F50) x 6

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

13mm Screw (F63) x 14

Drawer runner (F1004) x 2

9mm Screw (F74) x 2

Handle (F930) x 3

Small locking

nut (F3) x 2

Hinge (F522) x 6

Hinge plate

(F523) x 6

9mm Screw (F73) x 4

Knock-in Peg (F171GY) x 4

Plastic Nail

(F91) x 4

Wedgefix

(F639) x 4

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the drawer

front

Screw 2 metal dowels

into the holes shown on

the back of the drawer

front .

Note: Tighten the metal

dowels up fully against

the panels.

Step 3

80%

x 2

Prepare the drawer

sides

Insert a small locking

nut into the hole

shown on the left drawer

side and right drawer

side .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Step 2

Attach the drawer

sides to the drawer

front

Push the left drawer side

. and right drawer side

. onto the back of the

drawer front .

Turn the small locking

nuts on the left

drawer side and right

drawer side .

Note: Turn the locking

nuts clockwise to

secure panels - more

than 1/2 a turn.

Assembly Instructions

80%

x 2

Attach the handle

Attach a handle to the

drawer front using 2

screws .

Step 6

Fit the drawer base

Slide the drawer base

down the grooves in the

drawer sides and

and down into the

groove in the drawer

front . .

Step 5

Fit the drawer back

Fit the drawer back .

between the drawer

sides and .

Make sure that the

drawer base fits into

the groove in the drawer

back .

Hold the drawer back

in position and tap the

knock-in pegs

through the holes in the

drawer sides and .

6 7

Fit the wedgefixes

Turn the drawer assem-

bly over and slide 4

wedgefixes into the

front and back grooves,

as shown, and tighten up

the screws.

Step 7

Step 4

Assembly Instructions

Step 8

Profiled

front edge

Fit 3 hinge plates onto

the left side , making

sure that the slot is

facing towards the

finished front edge.

Screw 7 metal dowels

into the left side .

Note: Tighten the metal

dowels up fully against

the panels.

Push a rail holder into

the left side . Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

Finished

front edge

Back edge

Prepare left side

a: Place drawer runner

on the left side . Slide

back top of runner and

use 1st hole from the

front to fit 1st screw .

b: Slide runner back the

other way and fit the 2nd

screw into the corre-

sponding hole in the left

side .

Profiled

front edge

Profiled

front edge

Assembly Instructions

Step 9

80%

x 3

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Screw 7 metal dowels

into the right side .

Note: Tighten the metal

dowels up fully against

the panels.

Push a rail holder into

the right side . Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw . B

Prepare right side

a: Place drawer runner

on the right side .

Slide back top of runner

and use 1st hole from

the front to fit 1st screw

b: Slide runner back the

other way and fit the 2nd

screw into the corre-

sponding hole in the left

side .

finished

front edge

Profiled

front edge

2Profiled

front edge

Back edge

Assembly Instructions

Step 12

Step 10

Finished

front edge

Prepare the top

Tap 4 wooden dowels .

into the top .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Insert 4 large locking

nuts into the top .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Finished

front edge

plain

chipboard

surface

Step 11

Prepare the base

panels

Tap 4 wooden dowels .

into each of the 2 bases

Insert 4 large locking

nuts into each of 2

bases .

x 2

Step 12

Prepare the plinth

Tap 2 wooden dowels

into the plinth .

Insert 2 large locking

nuts into the plinth

Plain chipboard

surface

10mm

Profiled

front edge Finished

front edge

Finished

front edge

Assembly Instructions

Step 13

Fit the top and a base

to the right side

Push the top and 1

base onto the right

side as shown.

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the top and base .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

3 4

Profiled

front edge Finished

front edge

Step 14

Fit the other base and

the plinth to the right

side

Push the other base

and the plinth onto

the right side as

shown.

Use a screwdriver to

tighten the 3 large

locking nuts fitted to

the base and plinth

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

Note: Support the plinth

until the left side has been

fitted in the next step.

Andere Handbücher für Capella

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Aurora 147/1360 Bedienungsanleitung

Argos

Argos Denver 352/9045 Bedienungsanleitung

Argos

Argos Mia 3 Drawer Chest Bedienungsanleitung

Argos

Argos 9011179 Bedienungsanleitung

Argos

Argos Napoli 600/6266 Bedienungsanleitung

Argos

Argos Haversham Bedienungsanleitung

Argos

Argos Atlas Bedienungsanleitung

Argos

Argos Chunky 418/5897 Bedienungsanleitung

Argos

Argos 608/0811 Bedienungsanleitung

Argos

Argos 600/1986 Bedienungsanleitung

Argos

Argos 309/1951 Bedienungsanleitung

Argos

Argos Kingston 602/9779 Bedienungsanleitung

Argos

Argos Rattan 3566651 Bedienungsanleitung

Argos

Argos Romantic Series Bedienungsanleitung

Argos

Argos Venetia 630/3505 Bedienungsanleitung

Argos

Argos 833 /3559 Bedienungsanleitung

Argos

Argos HOME MID BACK GAMING CHAIR BLK 608/8734 Bedienungsanleitung

Argos

Argos Atlantic 759/0692 Bedienungsanleitung

Argos

Argos Haversham 376/6066 Bedienungsanleitung

Argos

Argos Malibu 238/7154 Bedienungsanleitung

Argos

Argos 228/7591 Bedienungsanleitung

Argos

Argos 042 3048 Series Bedienungsanleitung

Argos

Argos Linear 247/6216 Bedienungsanleitung

Argos

Argos Hallingford Gloss 790/7711 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung