Argos Caspian 355/9424 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Caspian - Desk

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 27/10/14

Important - Please read these instructions fully before starting assembly

355/9424

359/9439

ALR3099

Width - 100cm

Depth - 45cm

Height - 72cm

19/04/10 - Added ‘plain chipboard surface’ to all relevant panel drawings.

Added ‘finished front edge’ to upright drawings in steps 5 and 6.

Door drawing amended at step 18.

Issue 2 - 12/11/12 - Added code 617/1919

Issue 3 - 21/08/14 - Nail Holder no longer used.

NOTE: Hinge Arms are now L and Runners are O.

Issue 4 - 27/10/14 - New MK BQSP version.

Added Plastinails to kit.

New Argos codes.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 22kgs. Please lift

with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

• Parts of the assembly will be

easier with 2 people.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: If there is any

chance of this unit being pulled

over by children etc. it is

recommended that the unit is

secured to a wall using suitable

fixings (not supplied).

• Dispose of all packaging

carefully and responsibly.

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

Components - Panels

Please check you have all the panels listed below

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Left Side (D0367A)

(706 x 394mm)

Drawer Divider - D0034A

145 x 249mm

waterfall

Top (D0275A)

(1000 x 444mm)

Base (D0282A)

(349 x 392mm)

Upright (D0368A)

(706 x 394mm)

2Right Side (D0276A)

(706 x 394mm)

80%

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Shelf (D0285A)

(349 x 373mm)

Drawer Base (T161)

(299 x 330mm)

Modesty (D0277A)

(602 x 157mm)

Drawer Front (D0284A)

(345 x 157mm)

Door (D0288A)

(443 x 345mm)

Back (X725)

(626 x 373mm)

Plinth (D0022A)

(349 x 80mm)

Drawer Wrap (W161)

(943 x 95mm)

Please check you have all the fittings listed below

Tools required

Glue Safety - Take care when using glue, please follow the advice below

Skin contact: Remove contami-

nation by washing with soap and

water. This procedure should be

followed prior to aeting and

drinking.

Eye contact: Rinse immediately

with clean water for 15 minutes

and seek medical advice.

If swallowed: Seek medical

advice immediately.

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

• From time to time check that

there are no loose screws on

this unit.

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

Wooden dowel (F22) x 2

Metal dowel (F901) x 8 Shelf stud (F110) x 4

Large locking

nut (F900) x 6

Small locking

nut (F3) x 2

40mm Screw (F910) x 10

H I

Rule Scissors Hammer Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Hinge plate

(F523) x 2

Hinge (F522) x 2

Nail (F51) x 30

13mm Screw (F63) x 4

Handle (F923) x 2

19mm Screw (F461) x 4

9mm Screw (F74) x 2

9mm Screw (F73) x 4

Drawer runner (F1004) x 2

Plastic Nail (F91) x 6

Assembly Instructions

Prepare drawer front

and wrap

a: Screw 2 metal

dowels into the holes

shown on the back of the

drawer front .

Note: Tighten metal

dowels up fully against

the panel.

b: Insert 2 small locking

nuts into the holes

shown on the drawer

wrap .

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Assemble drawer

a: Place drawer base

into the narrow slot on

the drawer wrap .

Fold wrap around the

base.

b: Turn drawer wrap

assembly over and push

onto the back of the

drawer front .

Note: Turn locking

nuts clockwise to

secure panels - more

than 1/2 a turn.

10 10

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Assembly Instructions

Step 3

Step 4

Attach handle

Attach handle to the

drawer front using 2

screws .

Finished

front edge

Finished

front edge

Prepare the left side

a: Place a runner on

the left side . Slide

back the top of the

runner and use the 2nd

hole from the front to fit

the 1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the left side .

Fit hinge plates

making sure that the slot

is facing towards the

finished front edge.

Insert 2 large locking

nuts as shown.

Note: Arrow on locking

nut must point towards

hole in edge of panel.

Finished

front edge

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Prepare the upright

a: Place a runner on

the upright . Slide

back the top of the

runner and use the 2nd

hole from the front to fit

the 1st screw .

b: Slide the runner

back the other way and

fit the 2nd screw into

the corresponding hole

in the upright .

Insert 2 large locking

nuts as shown.

Prepare left and right

side

Separate runners .

a: Push fit 5 x left

runners marked ‘L’

into the holes shown on

left side .

Note: Runners must be

be fitted flat against the

panel. If necessary

gently tap into final

position.

Fit hinge plates

making sure that the slot

is facing towards the

finished front edge.

Push rail holder into

the hole shown. Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

b: Push fit 5 x right

runners marked ‘R’

into the holes shown on

right side .

Fit hinge plates

making sure that the slot

is facing towards the

finished front edge.

Push rail holder into

the hole shown. Make

sure that it is fitted

straight, in line with the

panel edges and then

secure with screw .

Step 5

Finished

front edge

Fit the base to the

upright

Attach the base to

the upright using 2

screws .

Finished

front edge

Step 6

Finished

front edge

Finished

front edge

Finished

front edge

plain

chipboard

surface

Assembly Instructions

Fit the plinth to the

upright

Attach plinth to the

upright using the

dowel already fitted and

secure with screw .

Step 7

Step 8

Step 9

10mm

Prepare plinth

Tap 2 wooden dowels

into the ends of the

plinth .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Fit the left side

Attach the left side to

the base and the

plinth using 3 screws

. .

Plain chipboard

surface

Plain chipboard

surface

Assembly Instructions

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

Rebated Edge

F73

COVERED EDGE

Use 2nd hole in from front of

Runner F1004 to fit 1st F73 then

fit other F73 to match other hole.

F1004

When you insert F900,

make sure the arrow is

pointing towards the hole

in the edge of the panel.

F900

F73

F1004

COVERED EDGE

Fit plinth to the

upright

Attach plinth to the

upright using the

dowel already fitted and

secure with screw .

Prepare the right side

Insert 2 large locking

nuts into the right

side .

Finished

front edge

Fit the modesty

2 people are needed

here

Attach the modesty

to the upright using 2

screws .

Support the modesty

until the right side has

been fitted in the next

stage.

Step 10

Step 11

Finished

front edge

plain chipboard surface

Assembly Instructions

Fit the right side

2 people are needed

here

Attach the right side

to the modesty using

2 screws .

Prepare the top panel

a: Screw 6 metal dowels

. into the holes on the

top .

Note: Tighten metal

dowels up fully against

the panel.

Step 12

Step 13

plain chipboard surface

Dieses Handbuch passt für folgende Modelle

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Chequer Corner 609/2452 Bedienungsanleitung

Argos

Argos Aspley 481/9651 Bedienungsanleitung

Argos

Argos 144/3556 Bedienungsanleitung

Argos

Argos 709/2592 Bedienungsanleitung

Argos

Argos 656/0159 Bedienungsanleitung

Argos

Argos Lavendon 275473 Bedienungsanleitung

Argos

Argos Home New Pagnell 601/9435 Bedienungsanleitung

Argos

Argos Fabric Ottoman With 2 Small Stools 755/2238 Bedienungsanleitung

Argos

Argos Holsted 1800 Bedienungsanleitung

Argos

Argos Cheval 147/2204 Bedienungsanleitung

Argos

Argos Alicia 188/8379 Bedienungsanleitung

Argos

Argos 245/7424 Bedienungsanleitung

Argos

Argos Scandinavia 630/2001 Bedienungsanleitung

Argos

Argos 239/2352 Bedienungsanleitung

Argos

Argos Carly Desk 617-2592 Bedienungsanleitung

Argos

Argos Oakhampton 391/8333 Bedienungsanleitung

Argos

Argos 465/9732 Bedienungsanleitung

Argos

Argos Denver 339/9622 Bedienungsanleitung

Argos

Argos Emmett 149/2765 Bedienungsanleitung

Argos

Argos Emberton 927/5788 Bedienungsanleitung

Argos

Argos Allura 7357103 Bedienungsanleitung

Argos

Argos Mendoza 228/9953 Bedienungsanleitung

Argos

Argos 603/0263 Bedienungsanleitung

Argos

Argos Nordic 4x2 Drawer Chest Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung