Argos New Sywell 355/9510 Bedienungsanleitung

MADE IN

BRITAIN

Dimensions

Width - 104cm

Depth - 50cm

Height - 172cm

New Sywell - 3 Door Mirror Robe

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 2 - 16/01/15

Important - Please read these instructions fully before starting assembly

ALR3092

355/9510

343/9692

323/2909

333/9259

Issue 2 - 16/01/15 - Back Holders now shown in vertical position.

Updated helpline number.

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs

approximately 67kgs.

Please lift with care.

• Check you have all the

components and tools listed on

pages 2 and 3.

• Remove all fittings from the

plastic bags and separate them

into their groups.

• Keep children and animals

away from the work area, small

parts could choke if swallowed.

• Parts of the assembly will be

easier with 2 people.

• Make sure you have enough

space to layout the parts before

starting.

• Do not stand or put weight on

the product, this could cause

damage.

• Assemble the item as close to

its final position (in the same

room) as possible.

• Assemble on a soft level

surface to avoid damaging the

unit or your floor (use opened

out unit carton).

Care and maintenance

• Only clean using a damp cloth

and mild detergent, do no use

bleach or abrasive cleaners.

• From time to time check that

there are no loose screws on

this unit.

• This product should not be

discarded with household

waste. Take to your local

authority waste disposal centre.

Note: If required the next page

can be cut out and used as

reference throughout the

assembly. Keep this page with

these instructions for future

reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws,

as this could damage the unit.

Only use hand screwdrivers.

• Safety note: It is

recommended that this unit is

secured to a wall using the

bracket supplied.

• Dispose of all packaging

carefully and responsibly.

Rule

Tools required

Rule

ScissorsSquare

Spirit

level

Hammer Bradawl

Eye protection

(when using a

hammer or drill)

Cross-head

screwdriver

Step

ladder

Electric drill

(only use

when drilling

into walls)

Components - Panels

Please check you have all the panels listed below

1 2 3

80%

x 3

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Left Side (D2560A)

(1711 x 496mm)

Right Side (D2569A)

(1711 x 496mm)

Upright (D2923A)

(1656 x 468mm)

Shelf (D2574A)

(322 x 468mm) x 3

Plain Door (D2563A)

(1650 x 333mm) x 2

Top (D2568A)

(1011 x 494mm)

Base (D2922A)

(1011 x 494mm)

Small Back (X1682-340)

(1682 x 340mm)

Large Back (X1682-694)

(1682 x 694mm)

7 8

9Mirror Door (D2563MA)

(1650 x 333mm) x 1

(Mirror - SG17

1647 x 300mm

Safety Back SAR)

Hanging Rail (FHR666)

(666mm long)

Rail (D2597A)

(674 x 125mm)

Please check you have all the fittings listed below

Components - Fittings If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases

more fittings may be supplied than are required.

A B C

D E F

G H

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K L

Hinge plate

(F523) x 9 Hinge (F522) x 9

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Ruler - Use this ruler to help correctly identify the screws

13mm Screw (F63) x 22

Large locking

nut (F900) x 14

Wooden dowel (F22) x 14 Metal dowel (F901) x 14

25mm Screw (F95) x 4

Rail Holder

(F891) x 2

Nail (F51) x 36

Shelf stud (F110) x 14

Nail screw (F277) x 5

Back holder (F276) x 5

*These can also be round

Plastic Nail (F91) x 4

Handle (F315) x 2

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Prepare the upright

a: Insert 4 large locking

nuts into the upright

. .

Note: The arrow on the

locking nut must point

towards the hole in the

edge of the panel.

Tap 4 wooden dowels

into the upright .

Note: Wooden dowels

must not stick out from

the edge by more than

10mm or they may

damage other panels.

Screw a metal dowel

into the upright .

Note: Tighten the metal

dowel up fully against

the panel.

b: Fit 3 hinge plates

onto the upright ,

making sure that the slot

is facing towards the

finished front edge.

Fit the rail holder to

the upright using 2

screws .

Step 1

Finished

front edge

10mm

Finished

front edge

Prepare top and base

a: Tap 4 wooden

dowels into the top .

Insert 4 large locking

nuts into the top .

Screw 2 metal dowels

into the top .

Note: Tighten the metal

dowels up fully against

the panels.

b: Tap 4 wooden

dowels into the base

Insert 4 large locking

nuts into the base

Screw 2 metal dowels

into the base .

Finished

front edge

Assembly Instructions

Step 2

Step 3

Prepare the top

Tap 4 wooden dowels

into the top .

Insert 4 large locking

nuts into the top .

Screw 2 metal dowels

into the top .

Note: Tighten the metal

dowels up fully against

the panels.

Finished

front edge

plain

chipboard

surface

Finished

front edge

Turn the

base over

Prepare the base

a: Tap 4 wooden dowels

. into the base .

Insert 4 large locking

nuts into the base

Turn the base over

b: Screw 2 metal

dowels into the base

. .

Assembly Instructions

Step 4

Step 5

Finished

front edge

Finished

front edge

Finished

front edge

Fit the top and base

to the upright

Push the top and the

base onto the upright

. .

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the upright .

Note: Turn the large

locking nuts as far as

they will go - more than

1/2 a turn.

plain

chipboard

surface

Finished

front edge

Prepare the left side

Screw 5 metal dowels

into the left side .

Note: Tighten the metal

dowels up fully against

the panels.

Fit 3 hinge plates onto

the left side , making

sure that the slot is

facing towards the

finished front edge.

Fit the rail holder to

the left side using 2

screws .

Assembly Instructions

Step 6

Step 7

Prepare the right side

Screw 4 metal dowels

into the right side .

Fit 3 hinge plates onto

the right side , making

sure that the slot is

facing towards the

finished front edge.

Finished

front edge

Fit the right side

Push the right side

onto the top and

base .

Use a screwdriver to

tighten the 4 large

locking nuts fitted to

the top and base .

Step 8

7 8

plain chipboard surface

Prepare the rail

Tap 2 wooden dowels

into the rail .

Insert 2 large locking

nuts into the rail .

Assembly Instructions

Step 9

Step 10

Finished

front edge

Fit the left side

Push the left side

onto the assembly.

Use a screwdriver to

tighten the 5 large

locking nuts fitted to

the top , base and

rail .

7 8

Fit the rail

Push the rail onto the

upright .

Use a screwdriver to

tighten the large locking

nut fitted to the rail .

C43

Note: Support the rail

until the left side has been

fitted in the next step.

Assembly Instructions

Step 11

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

Fit the back panel

a: Square up the unit by

making sure that

measurement x to x

equals y to y.

Place the small back

and large back down

onto the unit as shown,

with the white surface

facing the inside of the

unit.

Make sure that the 2

backs are pushed up

tight against each other

and that they meet in the

centre of the upright

panel’s edge.

b: Nail around the

outside edges only of the

2 back panels and

. .

Note: Do not

nail where the

backs meet.

Nails should be

spaced about

150mm apart.

c: Push the nail screws

. through the back

holders and tap them

down between the small

back and large back

. and into the back

edge of the divider.

Keep tapping the nail

screws in until the

back holders dig into

the small and large back.

NM +

Note: These can

also be round

Note: If ever you need to take

the backs off to dismantle the

unit, the nail screws can be

taken out using a screwdriver.

Note: Nails should

be spaced about

150mm apart.

Dieses Handbuch passt für folgende Modelle

Andere Argos Inneneinrichtung Handbücher

Argos

Argos Alicia 188/8379 Bedienungsanleitung

Argos

Argos HOME New Pagnell Deep 3+2 Chest 610/8793 Bedienungsanleitung

Argos

Argos 609/7024 Bedienungsanleitung

Argos

Argos Aurora 157/1844 Bedienungsanleitung

Argos

Argos Gabe Bedienungsanleitung

Argos

Argos 2274951 Bedienungsanleitung

Argos

Argos 548/5840 Bedienungsanleitung

Argos

Argos Costa Swivel Chair 6893307 Bedienungsanleitung

Argos

Argos Penelope Ottoman 899/8190 Bedienungsanleitung

Argos

Argos Alicia Bedienungsanleitung

Argos

Argos 356/3018 Bedienungsanleitung

Argos

Argos Newbridge 4830544 Bedienungsanleitung

Argos

Argos Yanniek 483/4124 Bedienungsanleitung

Argos

Argos OXFORD DINING FURNITURE Produktinformationsblatt

Argos

Argos Silbury 4083690 Bedienungsanleitung

Argos

Argos RONDA 7592573 Bedienungsanleitung

Argos

Argos Capella Bedienungsanleitung

Argos

Argos Habitat Winchester Tall TV Unit 414/7990 Bedienungsanleitung

Argos

Argos Cheval 152/6882 Bedienungsanleitung

Argos

Argos Ontario 149118 Bedienungsanleitung

Argos

Argos 719/3594 Bedienungsanleitung

Argos

Argos Malibu Tall Unit 833/7115 Bedienungsanleitung

Argos

Argos Lydiard Gloss 2008952 Bedienungsanleitung

Argos

Argos Westminster 424/3485 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung