Aspen CO2ZB1 Bedienungsanleitung

CO2ZB1ZigbeeCO2Sensor



InstallationInstructionsandUserManual



1. Specifications

Frequency:   2.4GHz(IEEE802.15.4)

OperatingTemperature: 14°‐122°F(‐10°‐50°C)

OperatingHumidity: 10%‐90%non‐condensing

CO2SensingRange:  400ppm–5000ppm

CO2SensingAccuracy: ±75ppm+5%MV

Battery:   4xAAAlkalineBattery

BatteryLife:  2Years(withdefaultsetting)

Compatibility:   Zigbee,

WWAH(WorkswithAllHubs)



2. PackageContents

1xSensor

2xScrews&WallAnchor

4xAAAlkalineBattery(uninstalled)

2xBackMounting2‐SidedAdhesiveTape

1xManual



3. ComponentIdentification



4. ZigbeeEnrollment:

ThisCO2Sensorneedstobepairedbeforeinstallation.

1. Insert4batteriestothebatterycompartment

2. TheLEDwillblinkthreetimesinambercolorevery2‐3secondswhile

scanningthenetwork.

3. Ifnetworksuccessfullyjoined,theLEDwillbelitfor1secondinambercolor

followedbyashortblinkingreencolor.

4. Ifnetworkisnotfoundafter1minute,thesensorwillgointosleepmode,

theLEDwillblinkinambercolorevery1minute.Youneedtoresetthe

sensortotriggerapairingprocess,andthensensorwillrepeatstepsfrom2

to4.



Toresetthesensor:

1. Removethebatteryfor10seconds

2. Pressandholddownthetamperswitchwhilere‐insertthebattery

3. Releasethetemperswitchwithin3secondsafterinsertthebattery



Note:MACaddressoftheSensorcanbefoundontheQRcodebyscanningit

withyourmobilephone.



5. Mounting



MountingbyScrew

Pressthecasereleasebuttontoseparatethefrontandwallanchorcase.

Thebackcasegivesaccesstoboththeflushmountandcornermount

screwknockouts.Drillthroughtheappropriateknockoutsandusethe

includedscrewstomountinthedesiredmountinglocation.

Itisrecommendedtoensurethereisatightsealaroundtheknockoutsto

preventbugsfromenteringthesensorandcausingfalsealarms.

Replacethefrontsensorcovertosnapshutandscrewinthesensorcase

screwsonthetopandbottomofthewallanchorcase.



MountingbyAdhesiveTap

Pressthecasereleasebuttontoseparatethefrontsensorcaseandwall

anchor.

Insertthebatteryintothebatterycompartment.

Putbackthewallanchorcasewithfrontsensorcase.

Placeonesideadhesivetapeoverthewallanchorcase,thesidethatwill

facethewall.

Peelofftheothersideofadhesivetape.

Placethesensoronthewall.



6. Operation



TheCO2sensorrequires45secondstowarmupforsignalstabilizingwhen

performingstartuporreset.Duringthewarmupperiod,theLEDwillblinkslowly

inamber.Duringnormaloperation,theLEDwillblinkevery5minutesingreen

colortoindicatethesensorisworkingproperly.However,therearenoLED

indicationswhenmotionisdetected.Thisisdonetomaximizebatterylife.

Furthermore,whenmotionisdetectedandasignalistransmittedtothepanel,

thesensorwillnottransmitagainforaperiodofthreeminutes.



7. Maintenance‐ReplacingtheBattery

Whenthebatteryislow,asignalwillbesenttothecontrolpanel.TheLEDwill

blinkevery2minutesinred.

Toinsertorreplacethebattery:

Removethesensorfromthewallanchorbyusingabottom‐to‐toplifting

motion.

RemovetheAAAlkalineBatteryandinstallnewAAbattery

Alwaysmatchtheplus(+)signonthebatterywiththeflatsideofthe

compartmentandtheminus(‐)signonthebatterywiththespringside.

Reinstallsensorbacktothewallanchorcase.



WARNING:Failuretofollowthesewarningsandinstructionscanleadtoheat

generation,rupture,leakage,explosion,fire,orotherinjury,ordamage.Donot

insertthebatteryintothecompartmentinthewrongdirection.Alwaysreplace

thebatterywiththesameorequivalenttype(seeSpecificationsonpage1).

Neverrechargeordisassemblethebattery.Neverplacethebatteryinfireor

water.Alwayskeepbatteriesawayfromsmallchildren.Ifbatteriesare

swallowed,promptlyseeadoctor.



Alwaysdisposeand/orrecycleusedbatteriesinaccordancewiththehazardous

wasterecoveryandrecyclingregulationsforyourlocation.Yourcity,state,or

countrymayalsorequireyoutocomplywithadditionalhandling,recycling,and

disposalrequirements.



8. EnvironmentalandOtherUsefulInformation



PleaseinstallCO2Sensorwithgoodairflowformoreaccuratesensingresult.

CO2Sensorisalsosensitivetoheatandvibration,pleaseavoidplacingthe

sensorclosetoexternalheatsourceordirectlyfromsunlight,aswellasfrom

vibratingdevicesuchasdevicewithmotor.

Avoidcontactwithwaterorotherfluids(watermaydamagethesensor,

thereforeminimizeexposurewhilewashing,orusingwaterforanypurpose.

CO2Sensorshouldnotbeusedinexcessivedustyordirtyareas.Thismay

damagetheCO2sensingability.

Donotthrow,knockorshakethedevice.Pleasehandledevicedelicatelyto

avoiddamagetosensor.



FCCComplianceStatement

Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothe

followingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,

and(2)thisdevicemustacceptanyinterferencereceived,includinginterference

thatmaycauseundesiredoperation.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassB

digitaldevices,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedto

providereasonableprotectionagainstharmfulinterferenceinaresidential

installation.Thisequipmentgeneratesusesandcanradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructionmanual,

maycauseharmfulinterferencetoradiocommunications.However,thereisno

guaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthis

equipmentdoescauseharmfulinterferencetoradioortelevisionreception,

whichcanbedeterminedbyturningtheequipmentoffandon,theuseris

encouragedtotrytocorrecttheinterferencebyoneormoreofthefollowing

measures:

•Re‐orientorrelocatethereceivingantenna

•Increasetheseparationbetweentheequipmentandreceiver

•Connecttheequipmenttoanoutletonadifferentcircuitfromthereceiver

•Consultthedealeroranexperiencedradio/TVcontractorforhelp.



Theuseriscautionedthatchangesandmodificationsmadetotheequipment

withouttheapprovalof

manufacturercouldvoidtheuser'sauthoritytooperatethisequipment.



FCCRadiationExposureStatement

ThisequipmentcomplieswithFCCRFradiationexposurelimitssentforthforan

uncontrolledenvironment.Thisequipmentshouldbeinstalledandoperated

withaminimumdistanceof20centimetersbetweentheradiatorandyourbody.

Theantennasusedforthistransmittermustbeinstalledtoprovideaseparation

distanceofatleast20cmfromallpersonsandmustnotbeco‐locatedor

operationinconjunctionwithanyotherantennaortransmitter.

IndustryCanadarequirements

ThisdevicecomplieswithIndustryCanadalicense‐exemptRSSstandard(s).

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynot

causeinterferenceand(2)thisdevicemustacceptanyinterference,including

interferencethatmaycauseundesiredoperationofthedevice

LepresentappareilestconformeauxCNRd'IndustrieCanadaapplicablesaux

appareilsradioexemptsdelicence.L'exploitationestautoriséeauxdeux

conditionssuivantes:(1)l'appareilnedoitpasproduiredebrouillage,et(2)

l'utilisateurdel'appareildoitacceptertoutbrouillageradioélectriquesubi,

mêmesilebrouillageestsusceptibled'encompromettrelefonctionnement”



CanadaRFexposurecompliance

TocomplywithRSS‐102requirements,aseparationdistanceof20cmmustbe

keptbetweenthedeviceandtheuseratalltimes.

PourseconformerauxexigencesRSS‐102,unedistancedeséparationde20cm

doitêtremaintenueentrel'appareiletl'utilisateuràtoutmoment.





.



UniversalElectronicsInc.



PN:47007‐0014190

REV&REVDate:A0210/21/2022



Andere Aspen Zubehör Handbücher

Aspen

Aspen 70-0200 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung