Assa Abloy Corbin Russwin CLX3300 Series Bedienungsanleitung

FM589 07/22

Installation Instructions

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com • www.corbinrusswin.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

Installation Instructions

2Product Components

1Tools Required

CLX3300 Series with BHSS Trim

Fig. Description

1 Inside escutcheon & lever assembly

2 Outside escutcheon & lever

assembly

3 Inside spring housing assembly

4 Screws - through-bolt (2) #12-24

x 1-1/2"

5 Lockbody assembly with rose liner

6 Outside spring housing assembly

7 Cylinder spacer

8 Cylinder

9 Key

10 Latch

11 Screws - latch (2) #8-32 x 3/4"

12 Screws - strike (2) #12-24 x 1"

13 Strike

14 Strike box (Optional)

15 Screws- through-bolt (3) #10-24 x

3-1/2"

3Door Preparation

IMPORTANT

• The accuracy of door preparation is critical for proper functioning and security of this lever handle lock. Misalignment can

cause premature wear and a lessening of security.

• Be sure to verify backset before marking and drilling door.

1. Use template FM623 to mark the door (Figure 1).

2. Drill the door according to the template.

3. Verify the dimensions (Figure 2).

4. Install the strike (Figure 3)

DOOR

FRAME

Desired

height

above

floor

Template

Backset must

match latch

Door bevel

Strike Box

Attaching Screws

#12 -24 x 1"

2x 7/16" (11mm) hole

1-1/8"

(29mm)

2-1/4"

(57mm)

1" (25mm)

hole

5/32" (4mm)

2-3/4"

(70mm)

3x 1/2" (13mm) hole

4-3/4"

(120mm)

1-11/16"

(43mm)

2-1/8"

(54mm)

hole

5/8"

(16mm)

• 5/32" drill bit • 1/2"drill bit • 7/16" drill bit • 1/8" drill bit

• #2 Phillips screwdriver • T25 Security Torx® screwdriver • T15 Security Torx® screwdriver

CLX3300 Series with BHSS Trim

Installation Instructions

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM589 07/22

5Door Thickness Adjustment (if necessary)

6Install Outside Lockbody Assembly

To adjust lock to door thickness if other than 1-3/4"

(44mm) refer to Section 5.

Insert lockbody assembly into door from outside

making sure that lockbody hooks latch case and

retractor engages bolt tail(s). (Figure 7)

DO NOT FORCE. (If lockbody does not engage latch

easily, check door preparation for errors.)

Latch bolt tail should be centered in depth of

retractor. If it is not, refer to Section 5 to properly

adjust the lock for door thickness.

Lock is factory preset for 1-3/4"(44mm) doors unless specified. To adjust lock to door thickness if other than 1-3/4"(44mm):

1. Remove outside spring housing from lockbody assembly. (Figure 5)

2. Rotate outside rose liner to adjust lock to fit door thickness, so distance (Dimension A) from inside surface of liner to

centerline of retractor is half the thickness of the door. (See chart and Figure 6)

3. Reassemble outside spring housing onto lockbody assembly.

Door Thickness Dimension A

1-3/4" (44 mm) 7/8" (22 mm)

2" (50 mm) 1" (25 mm)

4Latch Installation

Insert latch in door. (Be sure bevel edge of bolt faces strike plate.)

Attach with (2) #8-32 x 3/4"screws supplied.

Strike

Centerline of Retractor

Retractor

Dimension A

Important: Deadlocking latch must stop on strike when door is closed.

Outside Rose

Liner Lockbody

Assembly

Figure5

CLX3300 Series with BHSS Trim

Installation Instructions

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM589 07/22

7Cylinder Installation

IMPORTANT

Before installing cylinders:

• Use a flat blade screwdriver to rotate cam until the driver points

are in a 6 and 12 o’clock position. (Figure 8A)

Verify that the cylinder spacer is already installed into the shank

on the outside spring housing assembly. Cylinder spacer should be

removed for 7-Pin cylinder.

Note orientation of spacer, if it needs to be reinstalled.

1. Install cylinder into the lever. (Figure 8B)

• Remove temporary construction core or plastic core. If keyed, use

Control Key. Rotate 15° and pull.

• Insert permanent core into lever with control key. Rotate 15° and

remove key.

a Standard Cylinder (Figure 8)

b Interchangeable or Removable Core (Figure 9)

Key

BHSS Trim

Cylinder

Cylinder Spacer

Figure 8B

View into lock from end oftrim

12 o’clockdrive point

6o’clock drive point

Figure 8A

New Core

Figure 9

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com • www.corbinrusswin.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov.

CLX3300 Series with BHSS Trim

Installation Instructions

FM589 07/22

Competitor’s

Cylinder

Cap Pin

End Cap

Figure 11

9Cylinder Options

1. Provided less cylinder.

2. Depress cap pin and unscrew end cap to remove tailpiece from

competitor’s cylinder. (Figure 11)

3. Insert new tailpiece in orientation shown.

4. Reassemble end cap over new tailpiece.

a Lever to Accept Schlage®or Yale®Fixed Core Cylinder (M06 or YC Option)

8Install Inside and Outside Escutcheon & Lever Assemblies

1. Align and insert inside spring housing onto the installed lockbody.

2. Install (2) #12-24 x 1-1/2"screws to tighten the spring housing to the door.

3. Mount inside escutcheon and lever assembly over the inside spring housing.

4. Mount outside escutcheon and lever assembly over the outside spring housing.

5. Secure the assemblies using the (3) screws #10-24 x 3-1/2"(Figure 10)

Screws (2) #12-24 x 1-1/2"

Screws (3) #10-24 x 3-1/2"

Figure 10

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Corbin Russwin ED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff MAGAC-L Series Bedienungsanleitung

Assa Abloy

Assa Abloy 81 C Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lock YRC226 Technische Daten

Assa Abloy

Assa Abloy SARGENT IN Series Bedienungsanleitung

Assa Abloy

Assa Abloy Abloy EL648 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin HP3000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Cavity Lock Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron Magnalock M670BD Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 11 Line Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON CG0M19 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Mini Shear Magnet Bedienungsanleitung

Assa Abloy

Assa Abloy Union CodeGUARD 5 Montageanleitung

Assa Abloy

Assa Abloy KESO Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 843G Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8900 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC256 Technische Daten

Assa Abloy

Assa Abloy ASSA 88x Series Bedienungsanleitung

Assa Abloy

Assa Abloy E100 Bedienungsanleitung

Assa Abloy

Assa Abloy shine Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung