Assa Abloy Corbin Russwin CLX3361 Bedienungsanleitung

FM566-EN 6/22

Installation Instructions

For installation assistance contact Corbin Russwin:

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com.

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Pour le français, visiter: www.corbinrusswin.com/en/library/installation-instructions.

Installation Instructions

• #2 Phillips screwdriver

2Product Components

1Tools Required

• Lever release tool (provided) • 1/8" drill bit

• 5/16" drill bit • 5/32" drill bit

CLX3300 Cylindrical Lockset

Fig. Description

1 Inside lever handle

2 Rose/Scalp (2)

3 Screws - latch (2) #8-32 x 3/4"

4 Inside spring housing assembly

5Screws - through-bolt (2) #12-24

x 1-1/2"

6 Lockbody assembly with rose liner

7 Outside spring housing assembly

8 Cylinder spacer

9 Cylinder

10 Outside lever handle

11 Key

12 Lever release tool

13 Latch

14 Screws - strike (2) #12-24 x 1"

15 Strike

16 Strike box (Optional)

3Door Preparation

DOOR

FRAME

Desired

height

above

floor

Template

Backset must

match latch Door bevel

Figure1

5/16" (8mm) hole

2-1/8"

(54mm)

hole

1-1/8"

(29mm)

2-1/4"

(57mm)

1" (25mm)

hole

5/32" (4mm)

2-3/4"

(70 mm)

Figure2

IMPORTANT

• The accuracy of door preparation is critical for proper functioning and security of this lever handle lock. Misalignment can

cause premature wear and a lessening of security.

• Be sure to verify backset before marking and drilling door.

Strike Box

Attaching Screws

Strike Box

Attaching Screws

#8 -32 x 3/4"

#12 -24 x 1" Figure3

1. Use template FM567 to mark the door (See Figure 1).

2. Drill the door according to the template.

3. Verify the dimensions (See Figure 2).

4. Install the strike (See Figure 3)

CLX3300

Installation Instructions

Cylindrical Lockset

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM566-EN 6/22

5Adjust Lock for Door Thickness (if necessary)

6Install Outside Assembly

To adjust lock to door thickness if other than 1-3/4"

(44mm) refer to Section 5.

Insert outside trim assembly into door from outside

making sure that lockbody hooks latch case and

retractor engages bolt tail(s). See Figure 7.

DO NOT FORCE. (If lockbody does not engage latch

easily, check door preparation for errors.)

Latch bolt tail should be centered in depth of

retractor. If it is not, refer to Section 5 to properly

adjust the lock for door thickness.

Lock is factory preset for 1-3/4"(44mm) doors unless specified. To adjust lock to door thickness if other than 1-3/4"(44mm):

1. Remove outside trim assembly from the lockbody assembly. The lever, rose, and spring housing will remove as one piece

from the lockbody. See Figure 5.

2. Rotate outside rose liner to adjust lock to fit door thickness, so distance (Dimension A) from inside surface of liner to

centerline of retractor is half the thickness of the door. (See chart and Figure 6.)

3. Reassemble outside trim assembly onto lockbody assembly. Door Thickness Dimension A

1-3/4" (44 mm) 7/8" (22 mm)

2" (50 mm) 1" (25 mm)

2-1/4" (57 mm) 1-1/8" (29 mm)

Outside Rose Liner

Outside

Trim

Assembly

Lockbody

Assembly

Centerline of Retractor

Retractor

Figure5 Figure6

Dimension A

Figure7

4Latch Installation

Figure4

IMPORTANT: Deadlocking latch must stop on strike when door is closed.

Strike

Insert latch in door. (Be sure bevel edge of bolt faces strike plate.) Attach

with (2) #8-32 x 3/4" screws supplied.

CLX3300

Installation Instructions

Cylindrical Lockset

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM566-EN 6/22

Key

Outside Lever

Cylinder

Cylinder Spacer

7Install Inside Components

1. Remove rose from inside spring housing assembly.

2. Align and insert inside spring housing onto the installed lockbody.

3. Install screws to tighten the lock to the door.

4. Orient dimples on side of rose with openings on side of spring housing assembly. See Figure 8.

5. Install rose onto the inside spring housing assembly.

6. In the unlocked position, verify the button is adjusted properly. See Figure 9 for proper alignment. Adjust if necessary.

7. Install inside lever.

Note: Test for proper operation before closing door. Button in-line with shank in-

dicates correct position based

upon door thickness. If the

button needs to be adjusted,

position it by depressing the

plunger, moving it in or out as

needed.

Shank

Plunger

Screws (2) #12-24 x 1-1/2"

Figure8 Figure9

Rose dimple

8Cylinder Installation

IMPORTANT

Before installing cylinders:

• Use a flat blade screwdriver to rotate cam until the driver points

are in a 6 and 12 o’clock position. (See Figure 16 on next page)

Correct Key Orientation During Assembly

New Core

• Remove temporary construction core or plastic core. If keyed, use

Control Key. Rotate 15° and pull.

• Insert permanent core into lever with control key. Rotate 15° and

remove key.

Figure10

Figure11

a Standard Cylinder (Figure 10)

b Interchangeable or Removable Core (Figure 11)

Verify that the cylinder spacer is already installed into the shank on the outside

spring housing assembly. Cylinder spacer should be removed for 7-Pin cylinder.

Note orientation of spacer, if it needs to be reinstalled.

Rose dimple opening

CLX3300

Installation Instructions

Cylindrical Lockset

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM566-EN 6/22

10 Timing CLX3352 & CLX3382

1. Remove outside and inside levers. (See Section 9)

2. Adjust internal cams visible from both the outside

and inside lock trim.

2a. Use a slotted screwdriver to rotate each cam

until the driver points are in a 6 and 12 o’clock

position. (See Figure 16)

3. Re-install outside and inside levers.

4. Test both cylinders with key before closing the

door.

To Remove:

Rotate key 45° and hold. Depress lever catch with lever release tool.

9Lever Removal & Installation

Lever catch

To Remove:

Remove core and tailpiece, using key marked “control.”

Insert slotted screwdriver or lever release tool into cylinder opening and make

contact with lever catch.

Pull lever catch horizontally towards the opposite side of the cylinder opening

and remove lever.

To Install:

Without the core installed, slide the lever on over the lever catch. Confirm the

lever will not pull off. Install core and tailpiece, using key marked “control.”

To Remove:

Depress lever catch with lever release tool, remove

lever.

To Install:

Slide the lever on over the lever catch. Confirm the

lever will not pull off.

a Standard Cylinder (Figure 12)

b Interchangable or Removable Core (Figure 13)

c Plain Lever (Figure 13) & Push/Turn Button (Figure 14)

Control Key

To Install:

With driver points at 6 and 12 (See Figure 16), rotate key 45° in

either direction and slide lever on over the lever catch. Confirm the

lever will not pull off.

Figure12

Figure13

Figure14 Figure15

View into lock from end of trim

12 o’clock drive point

6 o’clock drive point

Figure16

CLX3300

Installation Instructions

Cylindrical Lockset

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM566-EN 6/22

Remove

b Install Half Dummy (CLX3350)

1. Remove inside lever. (See Section 9).

2. Remove rose.

3. Remove (2) mounting screws and inside housing assembly.

4. Remove outside trim assembly.

5. Push and hold plug back (located inside of outside trim assembly). See Figure 17.

6. Push lever catch with lever release tool and remove lever.

11 Other Function Instructions

a Remove Outside Lever for Exit Latch (CLX3340NT)

Figure18

Lever

Rose

(2) Mounting Screw

Inside Housing Assembly

Outside Trim

Assembly

Figure17

Push

Push and

Hold Plug

Screws (2) #12 - 24 x 1-1/2"

Cup Washer

Trim Assembly

CLX3300

Installation Instructions

Cylindrical Lockset

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM566-EN 6/22

c Install Full Dummy (CLX3370)

Figure19

11 Other Function Instructions, continued

Figure20

12 Miscellaneous Options

Install (1) adapter plate between the door

and rose assemblies (both sides).

• Inside trim to be aligned with holes

marked screw slot.

• Outside trim through-bolts to be

aligned with through-bolt holes

marked on adapter plate.

a 1-3/8" Doors (D138)

Outside Trim and

Lockbody

Adapter Plate

Inside Trim Assembly

Outside Trim Assembly

Screws (2) #12 - 24 x 1-1/2"

Inside Trim Assembly

CLX3300

Installation Instructions

Cylindrical Lockset

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

FM566-EN 6/22

Provided less core. Tailpiece included (See Figure 21).

1. If needed, rotate clip to leave appropriate slot on tailpiece open

for locking pin.

2. Remove key from core.

3. Unscrew threaded cap from end of core (it will be necessary to

depress the locking pin).

4. Place tailpiece inside the exposed end of core with locking pin

in open slot.

5. Reverse step 3 to reinstall cap.

6. Install core in lock normally.

See FM207 for more details.

1. Provided less cylinder.

2. Depress cap pin and unscrew end cap to remove

tailpiece from competitor’s cylinder.

3. Insert new tailpiece in orientation shown.

4. Re-aassemble end cap over new tailpiece.

b Lever to Accept Schlage®LFIC (M69)

c Lever to Accept Schlage®or Yale®Fixed Core Cylinder (M06 or YC Option)

12 Miscellaneous Options

Figure21

d Lever to Accept Yale®LFIC (YRC Option)

1. Provided less cylinder

2. Slide provided spacer over tailpiece

3. Insert driver assembly into back of core.

Competitor’s

Cylinder

Cap Pin

End Cap

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com • www.corbinrusswin.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov.

CLX3300

Installation Instructions

Cylindrical Lockset

FM566-EN 6/22

Pour le français, visiter: www.corbinrusswin.com/en/library/installation-instructions.

12 Miscellaneous Options

e CLX3329 Hotel Function Timing Adjustment

1. Set the lock to the unlocked position, remove lever and cylinder from the outside trim. See lever removal instruction on

page 4).

2. Insert adjustment tool (provided with lock) into interior cap located within the shank (Figures 22 & 23).

3. Rotate cap clockwise until fully tight (Figure 24).

4. Rotate cap back counter-clockwise (Figure 25) until tool handle is approximately in line with the end of the shank as shown

in Figure 26 for Fixed Core cylinder (FC) or in Figure 27 for Interchangeable Cylinder (LFIC). The flat on the tool should be at

the 12 o’clock position.

5. Install cylinder in the lever (see cylinder installation instruction on page 3).

6. Turn key 90 degrees counter-clockwise and install lever (with cylinder) onto shank.

Timing of the hotel cylinder is set at the factory for the standard door thickness. If the change key or emergency key does not

operate properly, follow the steps below:

Interior Cap

7. Test to confirm that both the operating and the emergency keys work properly in both the unlocked and locked (pushed/

pushed and turn) positions.

- If the operating key is still working in the locked position, the interior cap needs to be turned out (CCW) 1/2 turn.

- If the emergency key is not working in the locked position, the interior cap needs to be turned in (CW) 1/2 turn.

Figure22

Figure23

Figure24

Figure25 Figure26 Figure27

Troubleshooting:

- If having issue fine tuning the adjustment, re-start from #3.

- If cylinder will not install, re-start from #3.

Adjustment Tool

Flat on Tool

End of Shank

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Emtek Modern Keypad Entryset Betriebsanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD226 Technische Daten

Assa Abloy

Assa Abloy mFlipLock standard Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Bedienungsanleitung

Assa Abloy

Assa Abloy eCLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 319 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 800 TCAC2 Series Installationshandbuch

Assa Abloy

Assa Abloy Yale Assure Technische Daten

Assa Abloy

Assa Abloy Yale nexTouch Technische Daten

Assa Abloy

Assa Abloy Lockwood Cavity Lock Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CLX3300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff ANYKEY Bedienungsanleitung

Assa Abloy

Assa Abloy Code Handle Handbuch

Assa Abloy

Assa Abloy Corbin Russwin FE5400S Series Bedienungsanleitung

Assa Abloy

Assa Abloy PE920 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 5300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 179C Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Real Living YRDZW Technische Daten

Assa Abloy

Assa Abloy 179A S4 Benutzerhandbuch

Assa Abloy

Assa Abloy NORTON RIXSON CG0M19 Bedienungsanleitung

Assa Abloy

Assa Abloy eCLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy VERSO CLIQ V532 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung