Assa Abloy KESO KEK i-turn Bedienerhandbuch

ASSA ABLOY is the global leader in door opening solutions.

KESO KEK i-turn

Documentation

1Introduction ............................................................................3

2Product description..............................................................4

3Application site ......................................................................4

4Ordering information...........................................................4

5Dimensional drawing...........................................................5

6Requirements .........................................................................6

7Operation.................................................................................6

8Programming with KESO k-entryTM ..................................6

9Alarm and status signals......................................................8

10 Installation ...............................................................................9

11 Replacing the batteries..................................................... 10

12 Emergency power / emergency opening.................... 11

13 Technical data...................................................................... 12

14 Accessories and individual parts ................................... 13

15 Appendix ............................................................................... 14

16 Service & support ............................................................... 15

17 Notes....................................................................................... 16

Date of issue: 29.10.2010

Version: 009

ASSA ABLOY,

the global leader in

door opening solutions

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 3 of 18 Pages

1Introduction

This documentation is part of the KESO KEK i-turn thumbturn product family. It contains

important information on product handling and set-up operations. For this reason, you should

familiarise yourself with the content and, in particular, observe the instructions on safe

handling, operation and installation. When passing on this product to third parties, ensure that

they are also very familiar with this handling information.

This documentation is based on information that was correct at time of printing. KESO AG

accepts no liability for the correctness and completeness of the content of this documentation.

The figures or graphics shown may differ from the supplied components.

We reserve the right to make changes to reflect technical advancements. This

manual is not covered by our "Update Service".

KESO AG accepts no claims under warranty and no liability in cases of unauthorised

modifications or improper installation contrary to our assembly instructions and without

our prior consent.

1.1.1 Disposal

All articles listed in this documentation must not be disposed of as normal household

waste. It is the consumer’s responsibility to dispose of the product at a recycling

collection point for electrical and electronic waste. Disposing of this waste separately

helps to optimise reprocessing of all materials suitable for recycling and to reduce health and

environmental risks.

1.2 General safety instructions

= Instructions you must follow to ensure trouble-free operation.

1.3 Intended use

This product may only be used for applications specified in the catalogues and technical

descriptions, and only with devices and parts recommended or approved by KESO AG. Any

other use will be considered as incorrect. In the event of improper use, KESO AG will not accept

any liability for any possible damages and will not guarantee the perfect and correct functioning

of the components. Intended use implies adherence to all the instructions laid out in this

technical documentation. Correct and safe operation also includes transporting, storing,

installing and assembling the product as specified as well as careful and precise handling and

maintenance.

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 4 of 18 Pages

2Product description

The KESO KEK i-turn thumbturn is an electronic cylinder. It is intended for indoor use

only in locations where stricter control and safety requirements need to be met. The

KESO KEK i-turn thumbturn can be easily and quickly installed into existing doors

without any wiring. It can be adapted perfectly to structural conditions and fulfils high

architectural standards. k-entryTM, authorisations can be managed centrally in combination with

the KESO management software.

Like all KESO KEK products, the KESO KEK i-turn thumbturn is NOK (network on key)

compatible.

3Application site

For indoor use only.

The threshold values as specified in the technical data must be observed (see Item 13).

4Ordering information

Photo Item No. Designation/Description

21.43V.060.00.00.KT KESO KEK i-turn thumbturn double

cylinder

Standard length: 30/30 mm

Extension:

both sides, in 5 mm increments;

maximum 80/80 mm

21.43W.060.00.00.KT KESO KEK i-turn thumbturn single

cylinder

Standard length: 30/10 mm

Extension:

one side, in 5 mm increments;

maximum 80/10 mm

4.1 Scope of delivery

1 unit KESO KEK i-turn thumbturn cylinder with standard actuator

1 unit 65 mm fixing screw

1 unit Battery

1 unit Screw set

1 unit Assembly instructions

1 unit Tool for replacing the batteries

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 5 of 18 Pages

5Dimensional drawing

5.1 KESO KEK i-turn thumbturn double knob cylinder in EU profile

Article No.: 21.43V

Euro profile cylinders: Diameter ø17 mm with valve cut-out

5.2 KESO KEK i-turn thumbturn single cylinder in EU profile

Article No.: 21.43W.

Euro profile cylinders: Diameter ø17 mm with valve cut-out

Outside Inside

50.5 36.5

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 6 of 18 Pages

6Requirements

6.1 Hardware/software requirements

Authorisations managed and programmed using KESO k-entryTM Management

Software. Authorisations transferred using KESO KEK Programmer PPG V2 and the corresponding

KAPI programming cable.

6.2 Battery requirements

The KESO KEK i-turn thumbturn is fully battery-operated. Note the signals which indicate the

battery is running low. In cold weather, or if fitted in “cold” environments, check the battery

status several times a year. You can check the battery status using the KESO KEK Programmer

PPG V2 or a multimeter. The electronically stored data is not lost when you replace the battery.

When using the optional NOK function, the battery status is automatically logged by the

identification medium and transferred to the KESO k-entryTM Management Software via the NOK

terminal.

Important note:

Do not touch electronic components while changing the battery. Static discharge can

damage or even destroy electronic components.

Observe correct polarity when inserting batteries. Inserting the batteries incorrectly can

damage or even destroy electronic components.

KESO does not recommend using rechargeable batteries, as they do not have sufficient

capacity to match the power requirements.

As old batteries can leak, it is advisable to check the battery status at regular intervals.

KESO AG is not liable for consequential damage caused by defective batteries. We do

not offer a warranty for batteries.

Batteries must be disposed of separately in compliance with legislation in your country.

Frequent programming reduces battery life.

7Operation

The reader's contactless sensor is situated in the outside knob. The reader is highly

energy-efficient, a characteristic which results in a long battery life. When on standby, the

reader is in "sleep mode". You can wake the reader by moving the identification medium

(key, tag, card) within the reader range.

8Programming with KESO k-entryTM

The KESO k-entryTM Management Software is used as the standard tool for programming and

management.

Warning: always carry out programming and deletion operations with the door open to

prevent the door from closing accidentally.

8.1 Minimum user training

Programming with the KESO k-entryTM Management Software is basically the same as

programming with all other KESO KEK products.

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 7 of 18 Pages

8.2 Separate icons for KESO KEK i-turn thumbturn

The KESO KEK i-turn thumbturn has its own icon in the KESO k-entryTM Management

Software.

8.3 Programming interface

The KAPI programming interface is situated in the outside knob.

This interface may only be used in combination with the KESO KEK Programmer PPG V2

and the corresponding KAPI cable (see Item 14.6).

8.4 KESO k-entryTM Management Software settings

The KEK settings for the KESO KEK i-turn thumbturn can be programmed using the KESO k-entryTM

Management Software.

1. Release time:

Once access has been enabled, the outside knob remains engaged for the pre-set time.

You can set a time interval of between 0.5 and 25.5 seconds.

2. Optical signal - active:

Indicates authorisation and battery status on the outside door knob.

3. Optical signal indicating end of battery life - active:

Low battery status is indicated by a multistage alarm signal (optical) on the outside

door knob.

4. Optical signal during release - active:

The green LED lights up for the duration of the pre-set release time (see Item 1).

8.4.1 Function check

The KESO KEK i-turn thumbturn must be reprogrammed every time the device properties are

changed. Once changes are complete, check the functions using the authorised identification

medium.

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 8 of 18 Pages

9Alarm and status signals

Alarm and status signals can be set or changed at any time using the KESO k-entryTM

Management Software (see Item 8.4).

Such messages are set by default for each delivery as follows:

Function Default

status

Comment

Supply period ON active All system identification

media are authorised for

access. Once the product is

programmed for the first

time, this mode is inactive

and cannot be reset.

Release time 5 sec Range between 5 and 25.5

seconds

Optical signal active

Optical signal of battery end-of-life active

Optical signal during release active

If inactive, the battery life is

extended

9.1 Access authorised

Default setting:

•If access is authorised, the green LED flashes.

9.2 Access denied

Default setting:

•If access is denied, the red LED flashes.

9.3 Low battery status

Low battery status is indicated by a multistage alarm signal (optical).

KESO recommends checking the battery power status at least once a year using the

KESO KEK Programmer PPG V2 or a multimeter.

9.3.1 Pre-alarm threshold

If the battery level drops below the pre-warning threshold, the green and red LEDs flash

alternately when a KEK identification medium is held in proximity to the knob.

You should replace the batteries at your earliest convenience.

9.3.2 Alarm threshold

If the battery level drops below the alarm threshold, the green and red LEDs flash alternately

and at a fast rate when a KEK identification medium is held in proximity to the knob. The red

LED will then also flash every five seconds after this. If the battery level is about to reach the

specified minimum, the red and green LEDs flash every five seconds.

The batteries should be replaced as soon as possible.

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 9 of 18 Pages

10 Installation

Follow the installation instructions; your warranty becomes invalid if the product is

used or installed incorrectly. Read this installation guide carefully before installing. If

you have any queries regarding installation, please contact your dealer.

10.1 Individual parts of double door knob

Pos. Uni

Description Item No.

1 1 Cylinder body with assembled outside door knob

1.1 Outside door knob mechanism E.072

2 1 Inside door knob mechanism E.071

3 1 Lithium battery, type CR2 K.533

4 1 65 mm fixing screw G.100/65

5 1 Assembly tool K.554

10.2 Cylinder assembly in double door knob

A-3

A-2

A-1

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 10 of 18 Pages

11 Replacing the batteries

B-1

B-3

B-2

B-4

Remove cover

3Re

lace cove

KESO KEK i-turn

KESO AG, 10/2010 Subject to change Page 11 of 18 Pages

12 Emergency power / emergency opening

12.1 Electronic

The emergency power function only works in combination with the KESO KEK Programmer PPG

V2 and the corresponding KAPI programming cable.

Important note:

An authorised KESO identification medium must be inserted into, or placed on the

KESO KEK Programmer PPG V2.

1.) Insert the KAPI programming cable into the KESO KEK i-turn thumbturn interface.

2.) Connect the KAPI programming cable to the KESO KEK Programmer PPG V2.

3.) Hold/insert an authorised KEK identification medium into/onto the KESO KEK

Programmer PPG V2

4.) Start the KESO KEK Programmer PPG V2 and click on the menu item

«Emergency opening». Emergency opening is now complete. The thumbturn is engaged

and can now be opened.

12.2 Mechanical

A mechanical emergency opening cannot be implemented from the outside.

)

Interface for KAPI

programming cable

)

Insert

hold an

Ident data carrier

)

Activate emer

enc

opening

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy mFlipLock standard Bedienungsanleitung

Assa Abloy

Assa Abloy M32 Handbuch

Assa Abloy

Assa Abloy eCLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON DPA-12 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CL3300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron Magnalock M670BD Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT IN Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lock Lever Technische Daten

Assa Abloy

Assa Abloy Sargent PE8500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy R10 Bedienungsanleitung

Assa Abloy

Assa Abloy Code Handle Handbuch

Assa Abloy

Assa Abloy Corbin Russwin Access 800 9800 TCWI1 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Emtek Modern Keypad Entryset Betriebsanleitung

Assa Abloy

Assa Abloy Yale nexTouch NTB610 Technische Daten

Assa Abloy

Assa Abloy SARGENT Profile Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 6-Line Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 52-4424 Leitfaden

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRC256 Technische Daten

Assa Abloy

Assa Abloy Effeff Technilock L4 Series Bedienungsanleitung

Assa Abloy

Assa Abloy EL460 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CL3800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale eBoss 8850FL Series Bedienungsanleitung

Assa Abloy

Assa Abloy Pyramid Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung