Assa Abloy Corbin Russwin Access 800 9800 TCWI1 Series Bedienungsanleitung

written permission of Corbin Russwin, Inc. is prohibited.

Installation Instructions

For 9800 TWCI1 & TCPIP1 Series Trim by ED5000 Series

with SecureBolt™ and Rim Exit Devices

Attention Installer

Please read these instructions carefully to prevent missing important steps.

Please Note: Improper installations may result in damage to the lock and void the factory warranty.

Important: The accuracy of the door preparation is critical for proper functioning and security of this lock.

Misalignment can cause premature wear and a lessening of security.

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

CAUTION

TEST FOR

PROPER OPERATION

BEFORE CLOSING

DOOR

For installation assistance contact Corbin Russwin Inc., at 1-800-810-WIRE (9473)

FM336 10/18

WARNING

This product can expose

you to lead which is

known to the state of

California to cause cancer

and birth defects or other

reproductive harm. For

more information go to

www.P65warnings.ca.gov.

08/2018

FCC:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada:

The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical speciﬁcations

were met.

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des-

règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer

l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui

peut causer l’opération peu désirée.

Changes or modiﬁcations to this unit not expressly approved by ASSA ABLOY Inc.

could void the user’s authority to operate the equipment.

1) Warning................................................................................2

2) General Description/Speciﬁcations/Features ....................3

3) 9800 TWC1 Series Trim Product Illustration.......................4

4) Installation Instructions......................................................5

5) Operational Check ............................................................10

6) Hard Wiring Options .........................................................11

7) PIP (PoE) Wiring Options ..................................................12

Table of Contents

1) Warning

WARNING: To comply with “Fire Listed” doors, only alkaline batteries must be used.

written permission of Corbin Russwin, Inc. is prohibited.

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

The Corbin Russwin Access 800 TCWI1 Rim, SecureBolt™ Exit Device is designed for applications

requiring wireless access control. The TCWI1 is a self-contained microprocessor-controlled access

control product with non-volatile memory. It is able to utilize the existing wireless LAN 802.11 b/g in

order to communicate with the access control system. The TCWI1 lock will hold a total of 2000 different

user codes. This product is operated by six (6) “AA” alkaline batteries or by Corbin Russwin 784 9VDC

power supply. Corbin Russwin Access 800 TCWI1 Rim, SecureBolt™ Exit Devices are designed with

quality components to provide high security, performance and durability.

Using PoE technology coupled with approved third party software, this Access 800 TCWI1 Rim,

SecureBolt™ Exit Device offers a complete, integrated access control system.

The TCWI1 Rim, SecureBolt™ Exit Device may be used for both indoor and exterior applications.

A weather-protective gasket is recommended for exterior applications.

HID and iCLASS are registered trademarks of HID Global Corporation.

2) General Description / Speciﬁcations / Features

Features

• 2400 users per lock; 10,000 event audit trail

• Multiple time zone and holiday

access scheduling

• Centralized lock management

• Real time door status monitoring

• First-In unlock conﬁguration, either by time

or by user (selectable)

• Lock down capable

• Input Power: PoE Class 2 Device, as deﬁned

by IEEE 802.3af

• Supports HID®125 kHz prox or 13.56 MHz

iCLASS®credentials (26 - 39 bit); supports

CSN reads for other common 13.56 MHz

cards, including MiFare, DesFire and Felica

Speciﬁcations

• Latch – 1/2" standard

• 3/4” throw ﬁre rated double doors

• (optional) M16- preﬁx

• Inside lever retracts latch

Items Supplied with Exit Device Items

included with ED5 00 (S) (A) Rim or

SecureBolt Exit Device by 9800 TCWI1

Series Trim

• Outside Escutcheon with keypad

• Outside motorized Trim Assembly

• Exit Device

• Rim cylinder for 9834

• Inside Escutcheon with Circuit board and

battery Pack 6 "AA" alkaline batteries

• Screw Pack

• Locks furnished for 1-3/4" to 2" doors

• U.L. Listed

• Deadlocking latch

• For 2-1/4” doors specify option D214

• Cylinder override

• Outside lever controlled by keypad,

or key retracts latch

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

3) 9800 TCWI1 Series Trim Product Illustration

SecureBolt™ Shown

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

2Prep door according to supplied Corbin Russwin Inc. door marker.

This device is not handed, however the Trim assembly is handed. Door should be ﬁtted and

hung. Verify box label for size of exit device, function and hand.

Attach Fire Stop Plate

using (2) #8x 1/2"

Self-Tapping Screws

for Wood and Metal

Doors

CL of 1-1/2 Dia.

Fire Stop Plate required

for ﬁre rated doors

(2) 1/8” Diameter

Holes Required

Hole for ribbon cable

1-1/2#

Outside of

Door

The Optional Conduit is available

for Non Fire rated doors to provide

weather protection for exterior

door applications. It is included in

the M99 Weathersesal Gasketing

Kit when ordered with the device.

If ordered separately, order part

number 794F909.

Install conduit half with recessed

panel "Not For Use On Fire Door"

visible from outside of door.

Outside

Left Hand

Reverse

“LHR”

Right Hand

Reverse

”RHR”

4) Installation Instructions

Inside

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

NOTE:

Lever return spring is handed. Hand of trim

cannot be changed without correct spring.

Lever return spring handing can be identiﬁed

by the color of the spring:

LHR, part number 651F618 (Red)

RHR, part number 651F628 (Blue)

1. Check cylinder components.

NOTE: Cylinders longer than 1-1/8" (29mm) will require collars. Refer to Cylinder Chart Below.

2. When required, cut cylinder tailpiece.

Correct length is 1/16" to 3/16" (2 to 5 mm) beyond cylinder housing cam.

Assembly of cylinder:

• Insert cylinder housing prongs into matching notches of escutcheon.

• Pass cylinder tailpiece thru cylinder collar (when required) and slot cylinder housing cam.

• Fasten cylinder in escutcheon recess of collar using (2) mounting screws.

(DO NOT OVER TIGHTEN SCREWS.)

Escutcheon Assembly:

Lever is handed, LHR (show)

Rim Cylinder

Cylinder Collar

(if necessary)

Cam must be postitioned as shown

when cylinder tailpiece is assembled

4) Installation Instructions

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

4) Installation Instructions

Sleeve

for Metal

Door

DPS

Harness

Ground

Connect RX connectors

(2)1/4 - 20

Oval head

screws

(2) Finish

washers

Motor Harness

DPS

Motor Harness

Trim assembly

Cover

Gasket

(optional)

Gasket Application:

Peel off the adhesive protective from

gasket. Feed trim assembly motor

harness through gasket opening as

shown and ﬁrmly press gasket to

escutcheon, aligning edge of gasket with

the edge of the escutcheon.

Outside Trim Assembly

1. Route motor harness pigtail thru 3/4" diameter hole "C" on inside of door and out other side through

trim assembly prep. Connect to trim assembly motor harness.

2. Route RX connector thru hole "C" on inside of door, thru race way between hole "C" and trim cutout,

and through 1/2" diameter hole "D" back to inside of door.

Connect to the RX connector from the device.

3. Mount trim assembly to door pulling slack wire from motor harness pigtail towards device side of door.

Be careful not to pinch harness wires.

4. When mounting trim, lift tailpiece to pass through hole on device side. Ensure tailpiece is in

vertical position.

5. Fasten trim assembly to door through holes "A" using (2) 1/4-20 oval head screws and two (2)

ﬁnish washers. Finger tighten only!

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

4) Installation Instructions

Installation of Outside Keypad Escutcheon

1a. For ﬁre rated devices, feed keypad ribbon cable/connector and ground wire

from outside of door through ﬁre stop plate and hole in door.

1b. For non ﬁre rated exit devices, feed keypad ribbon cable/connector and

ground wire through hole in door.

2. Place escutcheon against door surface.

GASKET APPLICATION:

Peel off the adhesive protective paper from

gasket. Feed Keypad ribbon cable and ground

wire through gasket opening as shown and ﬁrmly

press gasket to escutcheon, aligning edge of

gasket with the edge of the escutcheon.

Keypad Ribbon Cable

Gasket

(optional)

Ground Wire

Fire Stop Plate

7 4) Installation Instructions

Battery Installation

1. Remove battery keeper by lifting top tab and pulling away from the unit.

2. Install (6) AA Batteries into controller compartment being careful to align +/-polarity properly.

3. Install Battery Keeper by ﬁrst inserting bottom tabs in bottom slots of controller. Lift the top

tab over batteries and snap into position.

4. Attach battery cover to inside controller escutcheon making sure to line up tabs with

retaining slots in battery cover. Secure with security screw using security T20 bit.

CAUTION

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

TEST

FOR PROPER

OPERATION

BEFORE

CLOSING

DOOR

Tabs

Battery Polarity

Battery Keeper

Bottom Tabs

Retaining Slots

Security Screw

T20 bit

Top Tab

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

FM336 9800 TCWI1 Series

written permission of Corbin Russwin, Inc. is prohibited.

1. For exit devices without cylinder override trims, go to Step 3 below.

2. For Rim and Secure olt exit devices with 9834 Series cylinder override trims.

a. Insert key into cylinder and rotate.

b. While holding key in rotated position, operate outside lever to retract latch.

c. They should rotate freely and outside lever should retract latch.

3. Depress exit device pushpad to retract latch.

4. Use Proximity Card or Pin code set up with Lock Conﬁguration Tool. This should unlock outside

lever and allow latch to be retracted. Please see Network Lock Conﬁguration Tool User Manual

(WFMN1) for more information.

5) Operational Check

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Pyramid Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 9600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy R10 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT Profile Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YD-01-CON-NOMOD-PB Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent FM-PE8700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 7800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 118 Series Bedienungsanleitung

Assa Abloy

Assa Abloy PADDE Series Bedienungsanleitung

Assa Abloy

Assa Abloy h.e.s. 9200 Series Handbuch

Assa Abloy

Assa Abloy effeff MAGG1200SM Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron DSB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 52-4424 Leitfaden

Assa Abloy

Assa Abloy MSL sFlipLock check Bedienungsanleitung

Assa Abloy

Assa Abloy HES 9400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT Profile Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Luna Pro Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON M19 Bedienungsanleitung

Assa Abloy

Assa Abloy MSL sFlipLock standard Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 530 DX Series Bedienungsanleitung

Assa Abloy

Assa Abloy ESA500 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung