Assa Abloy Pemko 4131RL Bedienungsanleitung

Installation Instructions:

1. If the ADB is to be installed in a semi-mortise, prepare door according to the dimensions shown in the proﬁle drawing on front of label.

NOTE: If a door is ﬁre labeled or of acoustical construction, semi-mortise preparation must be done by the door manufacturer or licensed machiner only.

2. Cut from end opposite actuating plunger only.

3. DO NOT cut off more than two (2) inches.

4. When cutting, be sure that the drop bar is ﬂush with the case on the plunger side and that the gasketing insert projects at least 1/8”.

• For semi-mortise installation, cut ADB to door width.

• For surface mounted installation, cut ADB 1/8” less than the distance between the stops.

5. Adjust and trim the gasketing insert so that it projects at least 1/16” at each end of the drop bar and case.

6. For nylon brush seal ADB’s, use bolt cutters or diagonal cutting pliers that will pinch the strip to retain the bristles (as shown in Figure 1).

7. Crimp the ends of the brush strip and drop bar to prevent the nylon brush from sliding (as shown in Figure 2).

8. With the actuating plunger at the hinge side, fasten the ADB to the door bottom with the screws provided, these Type AB screws will accommodate

hollow metal and wood doors.

9. For surface mounted installation, the plunger contacts the stop (as shown in Figure 3).

10. For semi-mortise mounted installation, the plunger contacts the rabbet (as shown in Figure 4).

11. The underside edge of the ADB case should be installed ﬂush with the bottom of the door.

12. For wood jambs, a #10 x 1/2” ﬂat head screw is furnished for installation at the point where the plunger contacts the jamb to prevent indenting.

13. Screw the actuating plunger in or out as required until the gasketing insert just touches the sealing surface when the door is closed.

14. It is only necessary to lightly compress the insert against the sealing surface to provide a good seal.

15. Further adjustments may be required for uneven surfaces.

Figure 1

Figure 2

Figure 3 - Surface Mounted

Figure 4 - Semi-Mortise Mounted

End Plate Installation Instructions:

End Plate

1. The automatic door bottom must be correctly installed and adjusted in

accordance with the installation instructions furnished with this product

(see other side).

2. Be sure that the drop bar (part that contains the seal) does not project

beyond the end of the case when the actuation plunger is depressed (as

shown in Figure 7). If it does project beyond the case, it was improperly

trimmed in the ﬁeld. This condition can be corrected by removing the unit

and trimming the excess.

NOTE: Under no condition should the insert project beyond the edge of

the case.

Figure 7 - Improper Drop Bar

This shows an improper drop

bar protruding from the end of

the case. The drop bar should be

ﬂush at both ends.

Drop Bar

Figure 8 - Properly Installed End Plate

This shows a properly installed

end plate. Do not use power tool

to tighten this screw.

End Plate

Figure 5 - Plunger End Plate

Figure 6 - End Plate

3. Insert the No. 10 x 1/2” ﬂat head screw into the central opening of the endplate and tighten with a small Phillips

screwdriver. Insert the end plate into the case at the lock edge side of the door. Power drivers are not suggested

as they may over-tighten the screw and possibly break the end plate (as shown in Figure 8).

4. Next insert the plunger end plate with the hexagon hole. This pushes straight in. It also serves to prevent the

plunger from rotating and changing adjustment (as shown in Figure 9 and Figure 10). If this end plate needs to

be removed for readjustment, it can be removed in two ways: (1) push the drop bar towards the hinge side of the

door and it will eject the end plate; (2) prying at the top of the end plate with a knife or other tool. Do not pry at

the bottom. This will cause it to break.

Figure 9

Plunger end plate prevents

the plunger adjustment from

rotating.

End Plate

Plunger

Figure 10

Plunger end plate installed.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING TO INSTALL END PLATES.

IMPORTANT! These parts are made from glass ﬁlled nylon. They are very strong, but brittle. Do not attempt to twist or

bend them or they will break. This is not a problem if properly installed or removed.

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Valencia Filip Bedienungsanleitung

Assa Abloy

Assa Abloy M32 Handbuch

Assa Abloy

Assa Abloy Effeff Technilock L4 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 7300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale nexTouch Technische Daten

Assa Abloy

Assa Abloy Corbin Russwin Access 700 ED5000N Series Bedienungsanleitung

Assa Abloy

Assa Abloy Valencia Hola Bedienungsanleitung

Assa Abloy

Assa Abloy EMTEK Tubular Monolithic Entry Set Bedienungsanleitung

Assa Abloy

Assa Abloy PADDE Series Bedienungsanleitung

Assa Abloy

Assa Abloy 1264 Bedienungsanleitung

Assa Abloy

Assa Abloy HES 9400 Betriebsanleitung

Assa Abloy

Assa Abloy ENTR Bedienungsanleitung

Assa Abloy

Assa Abloy UNILOCK LOXURY IX Bedienungsanleitung

Assa Abloy

Assa Abloy HES 9400 Betriebsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy PE920 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CL3800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YD-01-CON-NOMOD Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Security lock 309 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CLX3300 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

We.lock

We.lock SECBNEBL51 Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

JAKO

JAKO JKBTNX4 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung