Assa Abloy Corbin Russwin CLX3300 Bedienungsanleitung

FM566 05/21

Installation Instructions

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Installation Instructions

• #2 Phillips screwdriver

2Package Contents

1Tools Required

• Lever release tool (provided) • 1/8" drill bit• 5/16" drill bit • 2-1/8" Bore •1" Bore• 5/32" drill bit

CLX3300 Cylindrical Lockset

Fig. Description

1 Inside lever handle

2 Rose/Scalp (2)

3 Screws - latch (2) #8-32 x 3/4"

4 Inside spring housing assembly

5Screws - through-bolt (2) #12-24

x 1-1/2"

6 Lockbody assembly with rose liner

7 Outside spring housing assembly

8 Cylinder spacer

9 Cylinder

10 Outside lever handle

11 Key

12 Lever release tool

13 Latch

14 Screws - strike (2) #12-24 x 1"

15 Strike

16 Strike box (Optional)

3Door Preparation

DOOR

FRAME

Desired

height

above

floor

Template

Backset must

match latch Door bevel

Figure1

5/16" (8mm) hole

2-1/8"

(54mm)

hole

1-1/8"

(29mm)

2-1/4"

(57mm)

1" (25mm)

hole

5/32" (4mm)

2-3/4"

(70 mm)

Figure2

IMPORTANT

• The accuracy of door preparation is critical for proper functioning and security of this lever handle lock. Misalignment can

cause premature wear and a lessening of security.

• Be sure to verify backset before marking and drilling door.

IMPORTANT: Deadlocking latch must stop on

strike when door is closed.

Strike

Strike Box

Attaching Screws

Strike Box

Attaching Screws

#8 -32 x 3/4"

#12 -24 x 1"

Figure3

1. Use template FM567 to mark the door (See Figure 1).

2. Drill the door according to the template.

3. Verify the dimensions (See Figure 2).

4. Install the strike (See Figure 3)

CLX3300

Installation Instructions

Cylindrical Lockset

FM566 05/21

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

5Adjust Lock for Door Thickness (if necessary)

6Install Outside Assembly

To adjust lock to door thickness if other than 1-3/4"

(44mm) refer to Section 5.

Insert outside trim assembly into door from outside

making sure that lockbody hooks latch case and

retractor engages bolt tail(s). See Figure 7.

DO NOT FORCE. (If lockbody does not engage latch

easily, check door preparation for errors.)

Latch bolt tail should be centered in depth of

retractor. If it is not, refer to Section 5 to properly

adjust the lock for door thickness.

Lock is factory preset for 1-3/4"(44mm) doors unless specified. To adjust lock to door thickness if other than 1-3/4"(44mm):

1. Remove outside trim assembly from the lockbody assembly. The lever, rose, and spring housing will remove as one piece

from the lockbody. See Figure 5.

2. Rotate outside rose liner to adjust lock to fit door thickness, so distance (Dimension A) from inside surface of liner to

centerline of retractor is half the thickness of the door. (See chart and Figure 6.)

3. Reassemble outside trim assembly onto lockbody assembly. Door Thickness Dimension A

1-3/4" (44 mm) 7/8" (22 mm)

2" (50 mm) 1" (25 mm)

2-1/4" (57 mm) 1-1/8" (29 mm)

Outside Rose Liner

Outside

Trim

Assembly

Lockbody

Assembly

Centerline of Retractor

Retractor

Figure5 Figure6

Dimension A

Figure7

4Latch Installation

Install screws (2) #8-32 x 3/4". Figure4

CLX3300

Installation Instructions

Cylindrical Lockset

FM566 05/21

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

Key

Outside Lever

Cylinder

Cylinder Spacer

7Install Inside Components

1. Remove rose from inside spring housing assembly.

2. Align and insert inside spring housing onto the installed lockbody.

3. Install screws to tighten the lock to the door.

4. Orient dimples on side of rose with openings on side of spring housing assembly. See Figure 8.

5. Install rose onto the inside spring housing assembly.

6. In the unlocked position, verify the button is adjusted properly. See Figure 9 for proper alignment. Adjust if necessary.

7. Install inside lever.

Note: Test for proper operation before closing door. Button in-line with shank in-

dicates correct position based

upon door thickness. If the

button needs to be adjusted,

position it by depressing the

plunger, moving it in or out as

needed.

Shank

Plunger

Screws (2) #12-24 x 1-1/2"

Figure8 Figure9

Rose dimple

8Cylinder Installation

IMPORTANT

Before installing cylinders:

• Use a flat blade screwdriver to rotate cam until the driver points

are in a 6 and 12 o’clock position. (See Figure 16 on next page)

Correct Key Orientation During Assembly

New Core

• Remove temporary construction core or plastic core. If keyed, use

Control Key. Rotate 15° and pull.

• Insert permanent core into lever with control key. Rotate 15° and

remove key.

Figure10

Figure11

a Standard Cylinder (Figure 10)

b Interchangeable or Removable Core (Figure 11)

Verify that the cylinder spacer is already installed into the shank on the outside

spring housing assembly. Cylinder spacer should be removed for 7-Pin cylinder.

Note orientation of spacer, if it needs to be reinstalled.

Rose dimple opening

CLX3300

Installation Instructions

Cylindrical Lockset

FM566 05/21

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

10 Timing CLX3352 & CLX3382

1. Remove outside and inside levers. (See Section 9)

2. Adjust internal cams visible from both the outside

and inside lock trim.

2a. Use a slotted screwdriver to rotate each cam

until the driver points are in a 6 and 12 o’clock

position. (See Figure 16)

3. Re-install outside and inside levers.

4. Test both cylinders with key before closing the

door.

To Remove:

Rotate key 45° and hold. Depress lever catch with lever release tool.

9Lever Removal & Installation

Lever catch

To Remove:

Remove core and tailpiece, using key marked “control.”

Insert slotted screwdriver or lever release tool into cylinder opening and make

contact with lever catch.

Pull lever catch horizontally towards the opposite side of the cylinder opening

and remove lever.

To Install:

Without the core installed, slide the lever on over the lever catch. Confirm the

lever will not pull off. Install core and tailpiece, using key marked “control.”

To Remove:

Depress lever catch with lever release tool, remove

lever.

To Install:

Slide the lever on over the lever catch. Confirm the

lever will not pull off.

a Standard Cylinder (Figure 12)

b Interchangable or Removable Core (Figure 13)

c Plain Lever (Figure 13) & Push/Turn Button (Figure 14)

Control Key

To Install:

With driver points at 6 and 12 (See Figure 16), rotate key 45° in

either direction and slide lever on over the lever catch. Confirm the

lever will not pull off.

Figure12

Figure13

Figure14 Figure15

View into lock from end of trim

12 o’clock drive point

6 o’clock drive point

Figure16

CLX3300

Installation Instructions

Cylindrical Lockset

FM566 05/21

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

Remove

b Install Half Dummy (CLX3350)

1. Remove inside lever. (See Section 9).

2. Remove rose.

3. Remove (2) mounting screws and inside housing assembly.

4. Remove outside trim assembly.

5. Push and hold plug back (located inside of outside trim assembly). See Figure 17.

6. Push lever catch with lever release tool and remove lever.

11 Other Function Instructions

a Remove Outside Lever for Exit Latch (CLX3340NT)

Figure18

Lever

Rose

(2) Mounting Screw

Inside Housing Assembly

Outside Trim

Assembly

Figure17

Push

Push and

Hold Plug

Screws (2) #12 - 24 x 1-1/2"

Cup Washer

Trim Assembly

CLX3300

Installation Instructions

Cylindrical Lockset

FM566 05/21

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

c Install Full Dummy (CLX3370)

Figure19

11 Other Function Instructions, continued

Figure20

12 Miscellaneous Options

Install (1) adapter plate between the door

and rose assemblies (both sides).

• Inside trim to be aligned with holes

marked screw slot.

• Outside trim through-bolts to be

aligned with through-bolt holes

marked on adapter plate.

a 1-3/8" Doors (D138)

Outside Trim and

Lockbody

Adapter Plate

Inside Trim Assembly

Outside Trim Assembly

Screws (2) #12 - 24 x 1-1/2"

Inside Trim Assembly

CLX3300

Installation Instructions

Cylindrical Lockset

FM566 05/21

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com •www.corbinrusswin.com

Provided less core. Tailpiece included (See Figure 21).

1. If needed, rotate clip to leave appropriate slot on tailpiece open

for locking pin.

2. Remove key from core.

3. Unscrew threaded cap from end of core (it will be necessary to

depress the locking pin).

4. Place tailpiece inside the exposed end of core with locking pin

in open slot.

5. Reverse step 3 to reinstall cap.

6. Install core in lock normally.

See FM207 for more details.

1. Provided less cylinder.

2. Depress cap pin and unscrew end cap to remove

tailpiece from competitor’s cylinder.

3. Insert new tailpiece in orientation shown.

4. Re-aassemble end cap over new tailpiece.

b Lever to Accept Schlage®LFIC (M69)

c Lever to Accept Schlage®or Yale®Fixed Core Cylinder (M06 or YC Option)

12 Miscellaneous Options

Figure21

d Lever to Accept Yale®LFIC (YRC Option)

1. Provided less cylinder

2. Slide provided spacer over tailpiece

3. Insert driver assembly into back of core.

Competitor’s

Cylinder

Cap Pin

End Cap

FM566 05/21

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com • www.corbinrusswin.com

Reproduction in whole or in part without the express written permission of ASSA ABLOY Access

and Egress Hardware Group, Inc. is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov.

CLX3300

Installation Instructions

Cylindrical Lockset

12 Miscellaneous Options

e CLX3329 Hotel Function Adjustment

1. Remove lever, cylinder, and spacer from outside trim. The button on the inside trim should be in the unlocked position.

2. Insert adjustment tool (provided with lock) into interior cap as shown below.

3. Rotate cap clockwise until fully tight.

4. Rotate back counter-clockwise until tool handle is approximately in line with the end of the shank (as shown) AND cap slot

orientation is vertical. Slot alignment may require a slight rotation in either direction.

5. Remove adjustment tool and re-install spacer, cylinder, and lever. Lever install will require key be rotated 90°

counter-clockwise.

- To adjust timing of hotel cylinder key lockout indicator

cap

6. Test to confirm that both the operating and the emergency key work properly in both the unlocked and locked (pushed

and turned on button) positions.

- If the operating key is still working in the locked position, adjust cap a half of a turn CCW and retest.

- If the emergency key is not working properly in the locked position, adjust cap a half of a turn CW and retest.

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Connect 50 Bedienungsanleitung

Assa Abloy

Assa Abloy 8400 Bedienungsanleitung

Assa Abloy

Assa Abloy 7003 Bedienungsanleitung

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 7800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin Access 700 ED5000N Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff ANYKEY Bedienungsanleitung

Assa Abloy

Assa Abloy UNILOCK LOXURY IX Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT IN Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT IN120 Wi-Fi Series Bedienungsanleitung

Assa Abloy

Assa Abloy shine Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 809M Bedienungsanleitung

Assa Abloy

Assa Abloy Liscio Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Harmony Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CLX3300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy E100 Bedienungsanleitung

Assa Abloy

Assa Abloy 3090 Montageanleitung

Assa Abloy

Assa Abloy Yale Conexis L1 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS100 Aperio Handbuch

Assa Abloy

Assa Abloy HES 9400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Pemko 4131RL Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8893 Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 878 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung