Assa Abloy HES 9400 Betriebsanleitung

HES 9400/9500/9600/9700

Electric Strike

Installation Instructions and Frame Preparation

Product Components

A 9400/9500/9600/9700 Strike Body

B 9400/9500/9600/9700 Cover

C 1/4"-20 x 1" Mounting Screws

D #10-32 & 10-24 Lockdown Screws (optional)

E #6-32 x 1/4" Cover Screws

F 5/64" Hex Key

G 12-Volt and 24-Volt Pigtails

UL1034

• Static Strength: 1500 lbs

• Dynamic Strength: 70 ft – lbs

• Endurance: 250,000 cycles

UL294 Performance Levels

• Destructive Attack: Level I

• Line Security: Level I

• Endurance: Level IV

• Standby Power: Level I

Electrical Specifications

Electrical Ratings for Solenoid

Continuous Duty 12 VDC 24 VDC

Resistance in Ohms 24 96

mA Continuous Duty 500 250

Solenoids are rated at +/- 10% indicated value.

Minimum Wire Gauge

Requirements

(Based on Round Trip)

Solenoid Voltage

12 VDC 24 VDC

200 feet or less 18 gauge 22 gauge

200 – 300 feet 16 gauge 22 gauge

300 – 400 feet 16 gauge 20 gauge

Diagram 1: Product Components

NOTE: Installation wiring for the product and

wiring methods shall be in accordance with the

National Electrical Code, ANSI/NFPA70

CAUTION Before connecting any device at the installation site, verify input voltage using a multimeter.

Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage

exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty.

Preparing the Strike

For 12 VDC, the Plug In Connector (pigtail)

marked “12 VDC” should be used; for 24 VDC,

the pigtail marked “24 VDC” should be used.

1 SELECT the appropriate pigtail that

matches system power and electrically

CONNECT as illustrated in Diagram 1.

2 IF no connector is present,

THEN CONFIGURE the wires

as shown in Diagram 2.

3 IF using the Latchbolt Monitor (LBM)

or Latchbolt Strike Monitor (LBSM),

THEN REFER to Diagrams 5 and 6 to

complete wiring (see page 3).

Verifying the Operation Mode

The HES 9400/9500/9600/9700

Electric Strike is pre-set for FAIL SECURE

OPERATION as shown in Diagram 3.

1 VERIFY that both keepers are in

FAIL SECURE OPERATION.

Converting the Operation Mode

There are two Selector Stop Pins, one on the left

side and one on the right side. Both Selector Stop

Pins must be repositioned (as shown in Diagram

4) to convert the strike to FAIL SAFE OPERATION.

IN FAIL SAFE OPERATION: Both keepers

should be unlocked without power and

locked when power is applied.

1 To convert to FAIL SAFE OPERATION,

REMOVE the Selector Stop Pins on

each side of the strike body using

the provided 5/64" hex key.

2 MOVE the Selector Stop Pins to the FAIL

SAFE OPERATION position (towards the

center of the strike) as shown in Diagram 4.

3 TIGHTEN both Selector Stop Pins after

they have been moved to the FAIL SAFE

OPERATION position using the 5/64” hex key.

Red

Red/green

Black

Violet

Red

Black

Violet

Red/green

(+ 12 VDC)

(- NEG)

(+ 24 VDC)

(- NEG)

Electric

Strike

Electric

Strike

Connect

Together

Connect

Together

Connect

Together

Diagram 1: 12V to 24V Conversion Diagram 2: If Connector Is Missing

Selector Stop

Pin Location

Selector Stop

Pin Location

Diagram 3: Fail Secure Operation

Diagram 4: Fail Safe Operation

CAUTION FAIL SAFE OPERATION mode

should not be used in fire rated or windstorm

resistant applications.

Preparing the Frame

NOTE: When using a Corbin Russwin Series

5000 or Yale 7000 Series equipped with an

offset deadlatch, the deadlatch is located

just above the vertical alignment line as

shown in the dimesions on page 4.

• IDENTIFY and MARK the latchbolt

centerline on the frame.

• Using the dimensions provided on page

4, MARK all appropriate holes. If using a

HES 9000-ASB*, reference the installation

instructions provided with that product.

NOTE: In retrofit applications this may

require the exit device to shift horizontally

towards the hinge side of the door to

compensate for the HES 9000-ASB.

• PUNCH, DRILL and TAP the

marked holes as required.

* When mounting on an aluminum frame, with a

blade stop, an HES 9000-ASB (sold separately) is

necessary to provide a secure installation. The HES

9000-ASB is shown installed in Diagrams 8 and 9.

Finishing the Installation

• ELECTRICALLY CONNECT the HES

9400/9500/9600/9700 to the Plug In

Connector, and ATTACH the electric

strike to the jamb using the 1/4"-20

x 1"mounting screws provided.

• CHECK the latchbolt interaction with the

keepers to ensure proper engagement

and clearance. If horizontal adjustment is

needed, ADJUST the strike and LOCKDOWN

the horizontal adjustment using the

10-32 set screws illustrated on Diagram 7.

• TIGHTEN the two 1/4"-20 x 1"mounting screws.

• OPTIONAL LOCKDOWN FEATURE: INSTALL

the #10-24 UNC or 10-32 UNF lockdown

screw if additional security is required;

however, REMOVE the strike before drilling

hole. If using a HES 9000-ASB it will require

drilling and tapping of the lockdown hole.

• INSTALL the cover plate, and SECURE in

place using the #6-32 x 1/4"Cover Screws.

Diagram 2: If Connector Is Missing

Diagram 5

Latchbolt Monitor

White Common

Orange Normally Open

Green Normally Closed

Diagram 6

Latchbolt Strike Monitor

Brown Common

Blue Normally Open

Yellow Normally Closed

White

Brown

Orange

Blue

Green

Yellow

Diagram 7

Lockdown

Screw

(optional)

Set Screw

Location

Set Screw

Location

Mounting

Screw

Mounting

Screw

CAUTION IF no LOCKDOWN SCREW is used

the elctric strike WILL NOT be windstorm rated.

This pertains ONLY to the HES 9600 and 9700.

HES 9400 Mounted on

Hollow Metal Frame

[228.6mm]

7/8"

[22.5mm]

1-3/4"

[44.5mm]

1-1/16"

[27mm]

7/8"

[22.5mm]

1-5/16"

[33.3mm]

1-5/16"

[33.3mm]

4-1/8"

[104.8mm]

4-1/8"

[104.8mm]

1/2"

[12.7mm]

Clearance

for

LBM/LBSM

Wiring

Centerline

of Latchbolt

This edge

toward

door

Deadlatch Vertical Alignment.

USE this line as a reference to center deadlatch.

See note under “Preparing the Frame” on page 3.

Mounting

Hole

Locations

for

1/4-20 UNC

Mounting

Screws

Final Lockdown Feature 10-32 UNF or

10-24 UNC Screw (optional)

3/4"

[19mm]

Clearance

for Power

Wiring

Frame Preparation

Patent Pending and/or patent www.assaabloydss.com/patents

express written permission of Hanchett Entry Systems, Inc. is prohibited.

3026006.004 _2

techsupport.esh@assaabloy.com | assaabloyesh.com

800.626.7590 | 10027 S. 51st Street, Ste. 102 Phoenix, AZ 85044 USA

Dimensions

NOTE: Not to scale. For easy installation,

the HES 9000-MTK should be ordered.

Diagram 8

Diagram 9

HES 9000-ASB

(optional)

HES 9400 Mounted on

Aluminum Frame with Blade Stop

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy SARGENT7800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Cavity Lock Bedienungsanleitung

Assa Abloy

Assa Abloy v.G1 Sargent Bedienungsanleitung

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YD-01-CON-NOMOD Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED7800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON CG0M19 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Mini Shear Magnet Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy 1264 Bedienungsanleitung

Assa Abloy

Assa Abloy 1489 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 2828 Series Bedienungsanleitung

Assa Abloy

Assa Abloy v.G1 Sargent Bedienungsanleitung

Assa Abloy

Assa Abloy Arrow Revolution U4A-YRHCPZW0 Technische Daten

Assa Abloy

Assa Abloy effeff 843 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lock SL Technische Daten

Assa Abloy

Assa Abloy KESO Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDME 50 Pro Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YDLL/BLK Fehlerbehebungshandbuch

Assa Abloy

Assa Abloy Valencia Hola Bedienungsanleitung

Assa Abloy

Assa Abloy shine Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent IN220 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Security lock 309 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

We.lock

We.lock SECBNEBL51 Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

JAKO

JAKO JKBTNX4 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung