Assa Abloy Sargent AL-PE80 Series Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com

Installation Instructions

permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in damage

to the product and void the factory

warranty.

WARNING

A8325-1 05/23

AL-PE80 Series

Alarmed Exit Devices

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Tools Needed

The SARGENT Alarmed Exit is designed for areas that require an alarm to sound upon exiting. Once

armed, any push rail movement will activate the horn in the push rail. The horn will continue to sound for

two minutes and then shut off automatically. The LED will flash indicating a violation has occurred.

Manual dogging is provided standard on

non fire rated devices.

1” diameter hole(s) required for routing wires

into the door when remote option(s) is used.

• Installation must be performed by a trained service person.

• Basic installation is 9V alkaline battery operated. For hardwired option use 546 Wiring harness -

See instruction sheet included with kit.

• Field cut rail assemblies are not allowed. Exit device must be ordered from the factory for specific door width.

Notes:

General Description

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Miscellaneous Parts

End Cap

Mounting Plate

Rail Assembly

Alarm Insert Sub-Assembly

Chassis Cover

Chassis

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Door Preparation and Handing

Verify hand and bevel of door. Exit devices are always reverse bevel and are mounted on the

inside of the door.

AL-PE8800 RHRB

shown

Outside View Outside ViewInside View Inside View

Right Hand

Reverse Bevel

Hinges Right.

Open Outward

RHRB

Left Hand

Reverse Bevel

Hinges Left.

Open Outward

LHRB

AL-PE8800 LHRB

shown

Cylinder Installation or Replacement

Remove the battery and the battery box screws.

Disconnect the wire harness.

If the cylinder is factory installed, go to Step 5 Installation Instructions on page 6.

Note:

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Cylinder Installation or Replacement (continued)

Remove the original cylinder (or foam plug, if

ordered without the cylinder):

a. Remove the battery box to expose the rear side

of the cylinder side. Use caution not to damage

any wire or switch when opening the battery

box as it is still connected to the assembly with

the battery terminal wires.

b. Remove the cylinder nut and switch actuator.

c. Remove the original cylinder (or foam plug).

Switch

Actuator

Cylinder

Nut

Cylinder (or foam plug)

Battery

Box

Install the new cylinder:

a. Install the new cylinder to the insert sub-

assembly with the keyway closest to the switch

end.

b. Reinstall the switch actuator with its legs on

opposite sides of the toggle switch on the

alarm board.

c. Reinstall the cylinder nut, then tighten.

d. Replace the battery box.

Switch

Actuator

Cylinder

Nut

Cylinder

Battery

Box

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Installation Instructions (for retrofit kit)

Connect the wire harness.

Reinstall the battery box screws and the battery.

If an AL- prefix was ordered on a full device, refer to those instructions for the device installation.

The following instructions are for alarm setup.

Note:

Cylinder Installation or Replacement (continued)

Remove the existing rail:

a. Remove chassis cover and end cap.

b. Loosen the chassis mounting screws.

c. Remove the end bracket.

d. Slide the rail assembly from the chassis.

Remove the mount rail and standard insert from

the push and carrier sub-assembly.

dMount Rail

Insert

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Installation Instructions (for retrofit kit, continued)

Ca. Insert the trigger mechanism arms to the gap

on both sides of the dogging cam (if present).

b. Slide the trigger mechanism forward into the

slot at the back of the dogging slope until it

clicks into place.

c. Press and release the push rail to verify that

the trigger is properly installed.

Slide the mount rail until it stops on the dogging

slope, then install the alarm insert sub-assembly

with the cylinder close to the push. Make sure

to press the switch firmly against the trigger

mechanism.

Mount Rail

Alarm Insert

Sub-assembly

Reinstall the rail:

a. Slide the rail assembly to the chassis.

b. Reinstall the end bracket.

c. Tighten the chassis mounting screws.

d. Reinstall the chassis cover and end cap.

Push Rail

Trigger Mechanism

Dogging slope

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

To Arm Device Security / Tamper Violation

Low Battery Alert

Alarmed Exit (AL-) Standard Operating Instructions

Turn the key clockwise. The LED will flash yellow

(PASSAGE) for 15 seconds (default). A quick chirp

will sound and the LED will flash green (ARMED)

every 30 seconds. Signal indicates unit is armed.

NOTE: The unit is automatically armed 15 seconds

after the unit is turned on. Field selectable settings

listed on the next page.

Green LED

When ARMED, depressing the push rail will activate

the alarm. The alarm will sound and the LED will flash

red (VIOLATION). The alarm will continue for

2 minutes (default). After 2 minutes, the LED will

flash red every 30 seconds until rearmed using the

key. Turn the key counter clockwise to deactivate the

alarm, then clockwise to rearm.

Red LED

The alarm chirps intermittently to indicate low

battery. Change the battery.

Battery: 9V alkaline

Yellow LED

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Optional Settings

DS3 DS4 Timer Reset

OFF OFF 2 minutes

OFF ON 5 minutes

ON OFF 10 minutes

ON ON Continuous*

These field selectable switches can change the following functions:

DS1 DS2 Timer Reset

OFF OFF 7 seconds

OFF ON 10 seconds

ON OFF 15 seconds

ON ON 20 seconds

DS5

ON GREEN/ARMED

RED/VIOLATION

YELLOW/ PASSAGE (DEFAULT)

OFF GREEN/VIOLATION

RED/ARMED

YELLOW PASSAGE

DS6*

ON Monitor relay is enabled (will activate when rail is violated)

*Requires 546 wire harness. See optional 546 wiring instructions for more information.

Auto Alarm Reset Request to Exit/

Passage Time Delay

Recommend 3267 power supply and 546 wiring harness.

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

AL-PE80 Series

Installation Instructions

Alarmed Exit Devices

A8325-1 05/23

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy DC423.2 Bedienungsanleitung

Assa Abloy

Assa Abloy ES100 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Mini Shear Magnet Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Essential Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale PBS1 Bedienungsanleitung

Assa Abloy

Assa Abloy 1584 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff Technilock L4 Series Bedienungsanleitung

Assa Abloy

Assa Abloy h.e.s. 9200 Series Handbuch

Assa Abloy

Assa Abloy Corbin Russwin TL3700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lock SL Technische Daten

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin MP9800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale eBoss 886F Series Bedienungsanleitung

Assa Abloy

Assa Abloy 3090 Montageanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED8400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Valencia Bella Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT IN120 Wi-Fi Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8900 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CL3800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Aperio Bedienungsanleitung

Assa Abloy

Assa Abloy MSL sFlipLock check Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent BHL 8200 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung