Assa Abloy Sargent PE8300 Series Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com

Installation Instructions

permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in damage

to the product and void the factory

warranty.

WARNING

A8303-1 5/23

PE8300 & 12-PE8300 Series

Mortise Lock Type Exit Device

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

Screw Chart

SCREW

TOTAL QTY

SUPPLIED

WHERE USED

1/4" X 1/2" ROUND HEAD

MACHINE SCREW

(2) CHASSIS

(METAL DOOR)

1/4"-10 X 1" ROUND HEAD

WOOD SCREW

(2) CHASSIS

(WOOD DOOR)

#10-24 X 3/4" ROUND HEAD

MACHINE SCREW

(2) REAR MOUNTING PLATE

(METAL DOOR)

#10 X 1-1/4" ROUND HEAD

WOOD SCREW

(2) REAR MOUNTING PLATE

(WOOD DOOR)

#12-24 X 1/2" FLAT HEAD

MACHINE SCREW

(2) 908 STRIKE

(METAL FRAME)

(2) MORTISE LOCK BODY

(METAL DOOR)

#10 X 1" FLAT HEAD

WOOD SCREW

(2) 908 STRIKE

(WOOD FRAME)

(2) MORTISE LOCK BODY

(WOOD DOOR)

#8-32 X 5/16" W/ #6 OVAL HEAD

MACHINE SCREW

(4) CHASSIS COVER

(2) END CAP

1/4"-20 X 2-3/8" KNURLED FLAT HEAD

MACHINE SCREW

(2) EXIT TRIM

(IF USED)

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

PE8300 & 12-PE8300 Exploded View

Chassis

Cover

Arm

Push Rail Assembly

Mounting Plate

End Cap

Vertical reference

line (C Chassis)

“Lock Down Key”

To operate: Depress pushrail; insert hex key,

and turn counter clockwise.

Attention:

Not available with 12- (Fire Rated) PE8300

Exit Devices.

INSIDE

REVERSE

LEFT HAND

BEVEL

RIGHT HAND

REVERSE

BEVEL

OUTSIDE

THIS EXIT DEVICE IS HANDED

CHECK HAND OF DEVICE AGAINST APPLICATION

Left hand reverse bevel illustrated

Rail Cutting Guide (Provided)

Tools Needed

Support Block (Provided)

16-Cylinder Lockdown

(Exploded View for Clarity)

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

1. Check hand of door. This device is handed and non-reversible.

2. Install mullion, if used.

3. Fit and hang door.

4. For wood doors, use wood screws and prep accordingly.

The surface of the door where the exit device is to be applied must be ﬂush. Clear away

any raised projections to allow exit device to rest on the ﬂat surface of the door. If shim

kit is required, contact your distributor.

Note: Please refer to trim and other installation instructions provided in the box.

Product Overview

Before installation:

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

Obtain dimension to ﬁnished ﬂoor from template

or from relationship to strike prep. Mark vertical

centerline by measuring 2 3/4"off of the door

edge.

Place template against frame, centered on the

line marked in Step 1. Mark and prepare door

according to template.

Install the strike to door frame using ﬂat head

#12-24 x 1/2"long screws.

Install the mortise lock body using ﬂat head #12-

24 x 1/2"long screws.

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

Insert chassis lever into door prep opening

underneath the mortise lock lever.

A. Depress the chassis lift arm.

B. Slide chassis upwards until mortise latch bolt is

fully retracted (C).

While maintaining chassis position set in Step 6,

mark chassis mounting holes.

Drill and tap 1/4-20 holes in previously

marked chassis locations.

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

Install chassis to the door using 1/4-20 round head

screws supplied. Do not fully tighten screws.

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

If the rail doesn’t need to be cut, continue to page 9, step 10.

If the rail must be cut, follow these steps on page 7 and 8:

Refer to the individual exit device installation instructions for rail cutting requirements / restrictions.

Instructions will vary based on device type and options.

Do not cut closer than 1-5/8"from

the the front edge of the rail insert.

• Determine cut off dimension “X” by subtracting 2-7/8"

from dimension “Y”. Mark cut off point on mounting

rail. (See below.)

Vertical reference line (C of chassis)

2-7/8"

min.

For doors with stile rail, the stile must overlap by 5/16"min.

A. Ensure there isn’t a gap between the insert

and the dogging slope, and the carrier is

ﬂush with the mount.

DOGGING

SLOPE

INSERT

B. Mark rail at the required cut length.

Insert

Dogging

slope

Cut line

Mount

Carrier

Information for Cutting Rails

Rail Sizes Door Widths

MinimumStandard

E 32" 24"

F 36" 33"

J 42" 37"

G 48" 43"

Rail cutting guide

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

CUT LINE

F. Using a hack saw with a new blade or a chop

saw with a metal cutting blade, cut the rail,

ensuring that the blade stays pressed against

the rail cutting guide.

G. Deburr and smooth all cut edges with a ﬁle.

D. Wrap the rail and insert in masking tape, as

shown.

E. Place the rail cutting guide over the masking tape and align it with the cut line. Clamp the cut guide to the rail

using a C-clamp.

C. Ensure plastic insert support is installed under the

cut line.

Cut line

Rail Cutting Guide

Rail cutting guide, continued.

1-800-727-5477 • www.sargentlock.com

the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

PE8300 Series

Installation Instructions

Mortise Lock Type Exit Device

A8303-1 5/23

Depress chassis lift arm. Slide rail assembly

onto chassis.

Ensure rail carrier tabs are aligned with

chassis.

10 11

Fully tighten chassis screws.

Insert the end cap bracket into the rail assembly.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Valencia Filip Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff EX118P Series Bedienungsanleitung

Assa Abloy

Assa Abloy Union CodeGUARD 5 Montageanleitung

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD216 Technische Daten

Assa Abloy

Assa Abloy Yale Keyfree Connected Smart Lock Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CLX3361 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON CG0M19 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 843 Bedienungsanleitung

Assa Abloy

Assa Abloy M32 Handbuch

Assa Abloy

Assa Abloy LE932 Bedienungsanleitung

Assa Abloy

Assa Abloy CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy IKON VERSO CLIQ Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 843 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale YD-01-CON-NOMOD-PB Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy E100 Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON DPA-12 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent BHL 8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL574 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin EcoFlex NAC Series Montageanleitung

Assa Abloy

Assa Abloy 1584 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Security lock 309 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung