Assa Abloy Sargent BHL 8200 Series Bedienungsanleitung

A8259A 07/19

Installation Instructions

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

BHL Freewheeling

Trim Retrofit

For Trim purchased prior to August 2019

8200 Series

BHL Freewheeling Trim Retrofit

Installation Instructions

8200 Series

A8259A 07/19

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

TOC Table of Contents

1 Tools Required ..................................................................3

2 Package Contents ...............................................................3

3 Assembly........................................................................3

a Prepare Spring Cartridges .......................................................3

b Assemble Spring Cartridges into BHL Levers......................................4

c Rose Handing ...................................................................4

d Assemble Outside Adapter Plate and Rose .......................................5

4 Installation ......................................................................5

a Install Adapter Clutch............................................................5

b Install Outside Lever Assembly...................................................5

c Install Outside Trim ..............................................................6

d Install Inside Adapter Plate Assembly ............................................6

e Install Inside BHL Rose Assembly.................................................7

f Install Inside Lever Assembly.....................................................7

Attention Installer

Please read these instructions carefully to prevent missing important steps.

Notes

• Improper installation may result in damage to lock and void factory warranty.

• Other product brand names may be trademarks or registered trademarks of their respective owners

and are mentioned for reference only.

BHL Freewheeling Trim Retrofit

Installation Instructions

8200 Series

A8259A 07/19

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

1 Tools Required

• Phillips Screwdriver (# 2)

• Torx Tamper Resistant Driver (T-20)

• Torx Tamper Resistant Driver (T-10)

• Hex Key Driver 5/64"

2 Package Contents

82-0347

Spindle Spring

82-1360

Behavior Health Lever

Reuse from existing BHL Trim

81-0790 Spindle -90˚ Freewheel (1.72")

01-1421

Torx Screw 6-32x5/16

92-0103

Security Rose BHL 45 Freewheel

01-9641

Screw Button Head Hex Socket 6-32 x 7/16

81-0794

Adapter Clutch

81-0723TAB

Mounting Post

857F658

Adapter Clutch -90˚ Freewheel

82-5573 Inside BHL Adapter Plate Assembly

01-1495

Machine Screw (#8-32 x 5/8”)

92-0103

Security Rose BHL 45 Freewheel

82-5534

Spring Cartridge BHL

82-1829

Bushing (Outside)

92-2151

Adapter and Plate Assembly

82-5534

Spring Cartridge BHL

81-0790 (Used with 1/8” SCAR Plate) Spindle -90˚ Freewheel (1.72”)

81-0812 (Used without 1/8 SCAR Plate) Spindle -90˚ Freewheel (1.60”)

Inside

Outside

01-1421

Torx Screw 6-32x5/16

01-9641

Screw Button Head Hex Socket 6-32 x 7/16

82-1359

Behavior Health Lever

01-1440

Set Screw(1/4-28 x 7/8”)

82-0347 Spindle Spring

Figure1

3 Assembly

a Prepare Spring Cartridges

Remove clear adhesive tape liners from spring cartridges

before use. (Figure2)

Figure2

82-0723TAB

Mounting Post

BHL Freewheeling Trim Retrofit

Installation Instructions

8200 Series

A8259A 07/19

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Assembly (cont.)

b Assemble Spring Cartridges into BHL Levers

Press spring cartridge assemblies

into levers so that top of

spring cartridge is flush or slightly

below flush to lever’s top

surface. (Figure3)

Note

Clean lever surface with rubbing

alcohol prior to installing

spring cartridge.

c Rose Handing

• Review following figures that illustrate left and right roses. (Figure4)

Figure4

RH/RHR Outside or

LH/LHR Inside

LH/LHR Outside or

RH/RHR Inside

• Install button head screw into each rose. Use a 5/64" hex key to tighten screw firmly to rose. (Figure5)

Figure5

LH/LHR Outside or

RH/RHR Inside

Security Rose BHL

01-9641

Button Head Screw 6-32 X 7/16 LG

RH/RHR Outside or

LH/LHR Inside

Figure3

INCH

ANGLES

FRACTIONS

SURFACE FINISH

UNLESS OTHERWISE

SPECIFIED TOLERANCES

.01

DRAWN BY

MATERIAL

V8_03/14/2019

SURFACE/FINISH

THIRD ANGLE

HEAT TREATMENT

NOTICE TO PERSONS RECEIVING THIS DRAWING

AND/OR TECHNICAL INFORMATION

LEGACY ID

SHEET

CONFIGURATION

Default

VOLUME

SURFACE AREA

0.000000

SIZE

DATE CREATED DESIGNED BY

REV

SCALE

1:1

DOCUMENT ID

MASS

DRAWING NUMBER (ALT ID)

Inside Lever

82-1359

Outside Lever

82-1360

Finished Lever Assembly

BHL Freewheeling Trim Retrofit

Installation Instructions

8200 Series

A8259A 07/19

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

3 Assembly (cont.)

d Assemble Outside Adapter Plate and Rose

• Insert two (2) mounting posts into adapter plate. (Figure6)

• Install rose using four (4) security torx screws.

Note:

Tighten screws evenly.

(4) Security

Torx Screws

Rose Assembly

Adapter and Plate Assembly

with Mounting Posts

LH/LHR Outside Shown RH/RHR Outside Shown

Figure6

4 Installation

a Install Adapter Clutch

Install adapter clutch into

mortise lock hub. (Figure7)

Note:

Adapter clutch is oriented toward

latchbolt as shown.

b Install Outside Lever Assembly

Use outside bushing and spindle to connect rose/adapter plate assembly to outside lever

assembly. (Figure8)

Figure7

81-0794

Adapter Clutch

Hinge Side

Figure8

Bushing

(Outside)

Rose/Adapter Plate Assembly

Align rose screw with gap in spring cartridge

Outside Lever Assembly

81-0790 Spindle

Apply grease to

these surfaces

BHL Freewheeling Trim Retrofit

Installation Instructions

8200 Series

A8259A 07/19

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

4 Installation (cont.)

b Install Outside Lever Assembly (cont.)

• Insert spindle into bushing; ensure that

spindle is inserted no more than ¾"deep.

• Use spindle to rotate bushing

clockwise into outside lever hole.

• Fully tighten bushing, then unthread

bushing just enough to allow spindle to

be inserted into lever, keeping

bushing as tight as possible.

• Once assembled, spindle orientation

should be as shown. (Figure9)

Note:

Longer spindle used on outside

c Install Outside Trim

Figure10

LHR Outside Shown

Make sure spindle seats into clutch

adapter then proceed to step 4din

order to retain Outside Trim to door.

d Install Inside Adapter Plate Assembly

Install inside adapter plate assembly

using two (2) machine screws.

(Figure11)

Figure9

Note position

and orientation

of spindles.

LH Outside RH Outside

Figure11

01-1495

Machine Screw #8-32x5/8

Inside Adapter Plate Assembly

LHR Inside

Shown

BHL Freewheeling Trim Retrofit

Installation Instructions

8200 Series

A8259A 07/19

in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

4Installation (cont.)

e Install Inside BHL Rose Assembly

Attach inside rose assembly to inside adapter plate using four (4) security Torx screws. Tighten screws

evenly. (Figure12)

Figure12

IMPORTANT

Screw oriented towards latch

Security Torx Screws

LHR Inside

Shown

f Install Inside Lever Assembly

• Install inside Spindle. (Figure13)

• Install inside BHL lever assembly to inside adapter plate assembly using security torx set screw.

IMPORTANT

• Line up rose screw with gap on spring cartridge.

• Make sure machined end of spindle seats into clutch adapter before assembling lever onto rose.

(Figure13)

Note

• Inside of LHR shown.

• Shorter spindle used

on inside.

Figure13

Gap

Spindle

Security

Torx Set

Screw

Machined End

Rose Screw

Note position and

orientation of spindle.

Founded in the early 1800s, SARGENT®is a market leader in locksets, cylinders, door closers, exit

devices, electro-mechanical products and access control systems for new construction, renovation,

and replacement applications. The company’s customer base includes commercial construction,

institutional, and industrial markets.

in part without the express written permission ofSARGENT Manufacturing Company is prohibited..

SARGENT Manufacturing Company

100 Sargent Drive

New Haven, CT 06511 USA

800-727-5477

www.sargentlock.com

A8259A

07/19

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Corbin Russwin EcoFlex NAC Series Montageanleitung

Assa Abloy

Assa Abloy 1125 Series Benutzerhandbuch

Assa Abloy

Assa Abloy Sargent 7800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CLX3361 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent AL-PE80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin CLX3300 Bedienungsanleitung

Assa Abloy

Assa Abloy PEMKO 3495 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Doorman Bedienungsanleitung

Assa Abloy

Assa Abloy effeff MAG-600SM Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Assure Lock with Wi-Fi Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT IN120 Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 843ZY-1 Q41 Series Bedienungsanleitung

Assa Abloy

Assa Abloy CYE345 Bedienungsanleitung

Assa Abloy

Assa Abloy Code Handle Handbuch

Assa Abloy

Assa Abloy v.G1 Sargent Bedienungsanleitung

Assa Abloy

Assa Abloy 8788 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale nexTouch Technische Daten

Assa Abloy

Assa Abloy Code Handle Handbuch

Assa Abloy

Assa Abloy Harmony H1 Bedienungsanleitung

Assa Abloy

Assa Abloy HES KS100 Aperio Handbuch

Assa Abloy

Assa Abloy KESO KEK i-handle S Bedienerhandbuch

Assa Abloy

Assa Abloy Corbin Russwin BLSS ML2000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy MSL sFlipLock check Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff Technilock L4 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung