Assa Abloy Corbin Russwin ED5600 Series Bedienungsanleitung

FM168 12/20

Installation Instructions

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

ED5600(A) Series

Mortise Exit Devices

For Metal, Composite, and Wood Doors

Outside Trim: Device is packed ready for any compatible trim.

RHR Door LHR Door

Handed Mortise Lock

(See “To change mortise lock hand”)

Device is non handed

(2) 1/4-10 x 3/4" PRHMS or (2) #14 Wood Screws

End Cap

End Clamp

(3) 8-32 x 5/16" PUFHMS

Cover

Device Assembly

Mortise Lock

(2) 12-12-24 PUFHM/WS

Universal

Strike

Armored Front

Armored Front Screw

(2) 12-12-24 PUFHM/WS

(2) 1/4-20 x

3/4" PRHMS

(Special Head)

(2) 8-32 x 5/164" PUFHMS

Dogging

Feature to hold bolts retracted and touchpad depressed, for push-pull door

operation.

To Dog Device:

1. Insert dogging key.

2. Hold touchbar depressed.

3. Turn key 1/4 turn clockwise.

(Not a feature of fire labeled devices.)

5600(A) Series

Installation Instructions

Mortise Exit Devices

FM168 12/20

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

1 To Change Mortise Lock Hand

Shim Kit Option

650F951 Black Finish

Kit consists of Latch Head Shims (Device Cover seats on shim) and End Clamp Shims (End Cap seats on

shim).

Each shim is 1/8” (3.2mm) thick more than two shim thicknesses 1/4” (6.4mm), require longer device

mounting screws (not included).

Maintenance

1. Periodically remove covers and coat mechanisms with a silicone base lubricant. This is particularly

required in corrosive environments for proper product function.

2. Check mounting fasteners periodically. Retighten if found loose. Apply screw locking compound

(available at automotive part stores) or change part fasteners if screws continue to back out.

FM168 12/20

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5600(A) Series

Installation Instructions

Mortise Exit Devices

2 Pre-Installation

Unreinforced Door or Frames

Doors and Frames with walls having a structural thickness (metal skin plus reinforcement, or solid hardwood) to engage

less than (3) full screw threads, are considered unreinforced for hardware.

Unreinforced Doors: Use SNB (sex nuts and bolts).

Reinforced Door or

Frame engages at least

(3) screw threads.

Reinforcement

Door skin

Unreinforced Frames: Use Blind Rivet Nuts.

Note

Recommended fasteners for unreinforced openings

are not necessarily supplied by Corbin Russwin, Inc.

Minimum Door Stile

4-1/2 in. (114 mm)

Door and Frame must

meet structural and

dimensional specifi-

cations on exit device

template(s) for door

and frame preparation.

Door must

swing freely

Door must not

be warped

Door must

not bind

Door must

not sag

5600(A) Series

Installation Instructions

Mortise Exit Devices

FM168 12/20

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Installation

aMark Door

Locate and Mark Horizontal and Vertical Centerlines as shown.

LHR door shown. Preparation is typical for both door hands.

Note: Centerline of Lock (cutout) must match Horizontal Reference

centerline.

bPrepare Door and Frame

Factory prepared cutouts with field drilled

mounting holes are recommended. If door (lock)

and frame (strike) have to be mortised in the field,

do it before continuing (follow instructions on

installation template).

1. Locate and tape Trim Template to door.

(See instructions packed with Trim.)

2. Seat plastic template on door and stop

faces.

Vertical Reference

(Except Rim and SecureBolt®

Exit Devices)

LHR

RHR

Concealed Vertical Rod

All ED5000 Series Devices

Against Frame Stop or Mullion

(when applicable)

For Rim and SecureBolt®

Exit Devices Only

ED5200S

Mortise

Concealed Vertical Rod

All ED5000 Series Devices

Trim Only

Horizont

Against D

Trim Only

Vertical Reference

(Except Rim and Secur

Exit Devices)

Rim and

SecureBolt®

4. Insert lock into mortise, adjust front for door

edge (beveled or flat).

(2) Lock holes for 12-24 machine screws or for

#12 wood screws.

NOTE: Lock base front has to be field tight-ened in

place using two screws, each on lock case

top and bottom.

5. Seat strike in frame cutout.

(2) Strike holes for 12-24 machine screws or

for #12 wood screws.

3 Locate plastic template, aligning VERTICAL REFERENCE and HORIZONTAL REFERENCE lines on door and

template. Tape template to door face.

(a) Slot 1/2” (12.7) diameter x 1” (25.4) on centers thru inside door face, using the two half circles on

the plastic template for start and end of slot.

(b) Device holes for 1/4-20 machine screws (metal reinforced doors only) or for 3/8” (9.5) diameter

sex nuts and bolts. Metal reinforced doors only.

FM168 12/20

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5600(A) Series

Installation Instructions

Mortise Exit Devices

Device must seat flush on door surface or

on shims that keep it parallel to the door

face. Two shim kits maximum for standard

device in 1-3/4” (44) door. For thicker

doors, consult the factory.

cSize Device

3 Installation (continued)

dClear Raised Door Molding

5600(A) Series

Installation Instructions

Mortise Exit Devices

FM168 12/20

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

3 Installation (continued)

eInstall Components

A. Install Lock

Lock in hand, depress guardbolt.

Check that latchbolt is deadlocked.

Check that latchbolt lever (and cylinder lever,

hubs, and thumbpiece lever, if relevant)

operate the lock freely.

Insert Lock Body into door cavity.

Fasten to door edge (2 PUFHM/WS)

Note: Make sure that door reinforcing clips or

doorwalls support lock immovable (restricting

rocking motion).

E. Install Device

Seat Bar in place (Device finger must

engage latchbolt lever, thru slot in

lock case/cover, as shown in Detail 1).

Fasten Device Head (2 PRHMS or

SNB). Set Bar level. Locate End Clamp

holes. Prepare End Clamp mounting

holes. Fasten End Clamp in place.

(2 #1/4-20 PRHMS or 3/8" (9.5) Dia.

SNB).

F. Check Operation

1. Depress touchbar (bolt must

retract). Release touchbar (bolt

must extend).

2. Actuate trim (bolt must retract).

B. Install Armor Front

Fit over bolts and fasten to lock base front (2 PUFHMS). Check that bolts retract and extend freely.

C. Install Strike - Seat in place (lip bend away from opening) Fasten to frame (2 PUFHM/WS).

D. Install Trim - Follow instructions packed with trim.

Release trim actuator (bolt must extend).

3. (NOT FOR FIRE DEVICES) Depress touchbar, turn dogging key clock wise (bar must remain

depressed, bolt must remain retracted). Turn dogging key counter clockwise (bar and bolt must

return to extended position).

4. Close door. Latchbolt should fully engage into strike cavity, guardbolt should retract over strike

ramp. Door should not rattle.

NOTE: When resulting operation is faulty, check first for visible binding or interference. If there is no

apparent reason for the fault, remove item from the door and recheck its operation before assuming that

it is defective. If latchbolt travel is not adequate, adjust device finger as shown on Detail 2.

G. Tighten all Mounting Screws.

FM168 12/20

or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5600(A) Series

Installation Instructions

Mortise Exit Devices

3 Installation (continued)

fInstall Head Cover and End Cap

Use (2) 8-32 PFHMS for Cover and (3) 8-32 PFHMS for End Cap.

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Corbin Russwin, Inc.

225 Episcopal Road

Berlin, CT 06037 USA

Phone: 800-543-3658

Fax: 800-447-6714

www.corbinrusswin.com

FM168 12/20

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy RIXSON W73ER Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 855 Montageanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Pando Mini Go Bedienungsanleitung

Assa Abloy

Assa Abloy 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5200 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton CloserPlus CLP8101 Bedienungsanleitung

Assa Abloy

Assa Abloy DC135 Service-Handbuch

Assa Abloy

Assa Abloy SARGENT 351 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7200 Series Kurzanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy RD150-3 Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 1331 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR7500 Bedienungsanleitung

Assa Abloy

Assa Abloy G-S Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 3000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX89 Betriebsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW200i US Handbuch

Assa Abloy

Assa Abloy 332 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton LEO 5700 Series Kurzanleitung

Assa Abloy

Assa Abloy 78PRA-8L Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung