Assa Abloy SARGENT 351 Bedienungsanleitung

1Measure and mark holes, using dimensions shown below

Left hand shown; Right hand opposite

(See page 4 for additional details)

With provided fasteners, secure closer body to door

with power adjustment facing away from hinge

Prepare Holes

Pre-drill - 3/32" holes for self tapping screws

or #16 drill for #12-24 tap for machine screws

(Use 1/8" hole for fire rated wood doors)

A7347B

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

351 WITH OT,OTB,HT,HTB ARM AND TRACK

INSTALLATION INSTRUCTIONS (PULL SIDE)

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE

FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com

NOTE: AN AUXILIARY DOOR STOP IS REQUIRED

4A7347B

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

Backcheck range

Delayed action

range

Closing speed

range

Latching speed

range

1/8" hex socket

wrench

Use 1/8" hex wrench

to adjust valves

Adjust Door speed, and Latching speed valves to achieve the desired closing time. Recommend

6 seconds minimum from 90° to the closed position.

If Backcheck is required, adjust valve to achieve a slight cushioning effect. Auxiliary stop required.

If closer is equipped with Delayed Action, regulate valve to achieve the desired delay

Adjusting Closing Speeds

Door Width Exterior Doors Interior Doors

(Inches)

24-30 TURN nut 1-3 TURN nut 1-3

30-36 FACTORY SET FACTORY SET

36-42 TURN nut 1-4 TURN nut 1-3

42-48 TURN nut 7-9 TURN nut 4-6

Install cover as shown

SPRING POWER ADJUSTMENT GUIDELINES

Decrease

Increase

Adjusting Nut

5/8"

Insert is removable.

Place in unused opening.

Slide track over roller and install end caps. Se-

cure track to frame with screws provided. Holder/Bumper option end toward hinge

Assemble arm to closer with index mark on end of

spindle 45º from axis of arm as illustrated below.

Use washer and screw to retain arm (Right hand

door shown).

LEFT HAND DOOR

RIGHT HAND DOOR

Adjust closing power to the minimum required to reliably close and latch door.

- If door is hard to open, decrease power slightly.

- If door does not latch, increase power as required.

- Use the chart as a starting point.

- Doors adjusted with high closing power to overcome

strong draft conditions may exceed ADA standards.

A7347B

TENSION AD-

JUSTER

HOLDER

DEVICE

Mounting screw

A7347B

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

Backcheck range

Delayed action

range

Closing speed

range

Latching speed

range

1/8" hex socket

wrench

Use 1/8" hex wrench

to adjust valves

Adjust Door speed, and Latching speed valves to achieve the desired closing time. Recommend

6 seconds minimum from 90° to the closed position.

If Backcheck is required, adjust valve to achieve a slight cushioning effect. Auxiliary stop required.

If closer is equipped with Delayed Action, regulate valve to achieve the desired delay

Adjusting Closing Speeds

Door Width Exterior Doors Interior Doors

(Inches)

24-30 TURN nut 1-3 TURN nut 1-3

30-36 FACTORY SET FACTORY SET

36-42 TURN nut 1-4 TURN nut 1-3

42-48 TURN nut 7-9 TURN nut 4-6

Install cover as shown

SPRING POWER ADJUSTMENT GUIDELINES

Decrease

Increase

Adjusting Nut

5/8"

Insert is removable.

Place in unused opening.

Slide track over roller and install end caps. Se-

cure track to frame with screws provided. Holder/Bumper option end toward hinge

Assemble arm to closer with index mark on end of

spindle 45º from axis of arm as illustrated below.

Use washer and screw to retain arm (Right hand

door shown).

LEFT HAND DOOR

RIGHT HAND DOOR

Adjust closing power to the minimum required to reliably close and latch door.

- If door is hard to open, decrease power slightly.

- If door does not latch, increase power as required.

- Use the chart as a starting point.

- Doors adjusted with high closing power to overcome

strong draft conditions may exceed ADA standards.

A7347B

TENSION AD-

JUSTER

HOLDER

DEVICE

Mounting screw

A7347B

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

1Measure and mark holes, using dimensions shown below

Left hand shown; Right hand opposite

(See page 4 for additional details)

With provided fasteners, secure closer body to door

with power adjustment facing away from hinge

Prepare Holes

Pre-drill - 3/32" holes for self tapping screws

or #16 drill for #12-24 tap for machine screws

(Use 1/8" hole for fire rated wood doors)

A7347B

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

351 WITH OT,OTB,HT,HTB ARM AND TRACK

INSTALLATION INSTRUCTIONS (PULL SIDE)

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE

FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 • www.sargentlock.com

NOTE: AN AUXILIARY DOOR STOP IS REQUIRED

4A7347B

Reproduction in whole or in part without the express written

permission of SARGENT Manufacturing is prohibited.

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy NORTON RIXSON 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 1370 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR7500 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5400 (A) Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED7400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW60 Handbuch

Assa Abloy

Assa Abloy G-CO-CS Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9540 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5700 Series Kurzanleitung

Assa Abloy

Assa Abloy Adams Rite EX88 Betriebsanleitung

Assa Abloy

Assa Abloy SARGENT Powerglide 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 3828 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR1601BF Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 78PRA-8L Bedienungsanleitung

Assa Abloy

Assa Abloy King 70 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Label

Label NEPTIS/LE Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Olide

Olide 120B Bedienungsanleitung

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt