Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Installation Instructions

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in damage

to the product and void the factory

warranty.

WARNING

FM580 1/23

Mortise Lock Type Exit Device

PED5600 & PED5600 A Series

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Screw Chart

DESCRIPTION

TOTAL QTY

SUPPLIED

WHERE USED

#10-24 X 3/4" FLAT HEAD

MACHINE SCREW

(4) CHASSIS

CORNER MOUNTING HOLES

(METAL DOOR)

#10 X 1-1/4" FLAT HEAD

WOOD SCREW

(4) CHASSIS

CORNER MOUNTING HOLES

(WOOD DOOR)

#10-24 X 3/4" ROUND HEAD

MACHINE SCREW

(2) REAR MOUNTING PLATE

(METAL DOOR)

#10 X 1-1/4" ROUND HEAD

WOOD SCREW

(2) REAR MOUNTING PLATE

(WOOD DOOR)

#12-24 X 1/2" FLAT HEAD

MACHINE SCREW

(2) 908 STRIKE

(METAL FRAME)

(2) MORTISE LOCK BODY

(METAL DOOR)

#12 X 1" FLAT HEAD

WOOD SCREW

(2) 908 STRIKE

(WOOD FRAME)

(2) MORTISE LOCK BODY

(WOOD DOOR)

#8-32 X 5/16" W/ #6 OVAL HEAD

MACHINE SCREW

(2) CHASSIS COVER

FRAME SIDE

(2) END CAP

#8-32 X 5/8" W/ #6 OVAL HEAD

MACHINE SCREW

2(2) CHASSIS COVER

RAIL SIDE

1/4"-20 X 2-3/8" KNURLED FLAT HEAD

MACHINE SCREW

(2) EXIT TRIM

(IF USED)

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

PED5600 & PED5600 A Exploded View

Rail Cutting Guide (Provided)

Tools Needed

Support Block (Provided)

M52-Cylinder Lockdown

(Exploded View for Clarity)

Mortise

Cover

Arm

Push Rail Assembly

Mounting Plate

End Cap

Vertical reference

line (C Chassis)

INSIDE

REVERSE

LEFT HAND

BEVEL

RIGHT HAND

REVERSE

BEVEL

OUTSIDE

THIS EXIT DEVICE IS HANDED

CHECK HAND OF DEVICE AGAINST APPLICATION

Left hand reverse bevel

illustrated

Chassis

“Lock Down Key”

To operate: Depress pushrail; insert hex

key, and turn counter clockwise.

Attention:

Not available with Fire Rated PED5600 A

Exit Devices.

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

1. Check hand of door. This device is handed and non-reversible.

2. Install mullion, if used.

3. Fit and hang door.

4. For wood doors, use wood screws and prep accordingly.

The surface of the door where the exit device is to be applied must be flush. Clear away

any raised projections to allow exit device to rest on the flat surface of the door. If shim

kit is required, contact your distributor.

Note: Please refer to trim and other installation instructions provided in the box.

Product Overview

Before installation:

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Obtain dimension to finished floor from template

or from relationship to strike prep. Mark vertical

centerline by measuring 2 3/4"off of the door edge.

Place template against frame, centered on the

line marked in Step 1. Mark and prepare door

according to template.

Install the strike to door frame using flat head

#12-24 x 1/2"long screws.

Install the mortise lock body using flat head

#12-24 x 1/2"long screws.

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

While maintaining chassis position set in Step 6,

mark chassis mounting holes.

Drill and tap #10-24 holes in previously

marked chassis locations.

Insert chassis lever into door prep opening

underneath the mortise lock lever.

A. Depress the chassis lift arm.

B. Slide chassis upwards until mortise latch bolt is

fully retracted (C).

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Install chassis to the door using #10-24

flathead screws supplied. Do not fully tighten

screws.

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

If the rail doesn’t need to be cut, continue to page 9, step 10.

If the rail must be cut, follow these steps on page 7 and 8:

Refer to the individual exit device installation instructions for rail cutting requirements / restrictions.

Instructions will vary based on device type and options.

Do not cut closer than 1-5/8"from

the the front edge of the rail insert.

• Determine cut off dimension “X” by subtracting 2-7/8"

from dimension “Y”. Mark cut off point on mounting

rail. (See below.)

Verticle reference line (C of chassis)

2-7/8"

min.

For doors with stile rail, the stile must overlap by 5/16"min.

A. Ensure there isn’t a gap between the insert

and the dogging slope, and the carrier is

flush with the mount.

B. Mark rail at the required cut length.

Insert

Dogging

slope Cut line

Mount

Carrier

Information for Cutting Rails

Rail Sizes Door Widths

Standard Minimum

32" 24"

36" 33"

42" 37"

48" 43"

W032

W042

W048

W036 (Std.)

Rail cutting guide

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

CUT LINE

F. Using a hack saw with a new blade or a chop

saw with a metal cutting blade, cut the rail,

ensuring that the blade stays pressed against

the rail cutting guide.

G. Deburr and smooth all cut edges with a file.

D. Wrap the rail and insert in masking tape, as

shown.

E. Place the rail cutting guide over the masking tape and align it with the cut line. Clamp the cut guide to the rail

using a C-clamp.

C. Ensure plastic insert support is installed under the

cut line.

Cut line

Rail Cutting Guide

Rail cutting guide, continued.

PED5600 & PED5600 A Series

Installation Instructions

Mortise Lock Type Exit Device

FM580 1/23

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Depress chassis lift arm. Slide rail assembly

onto chassis.

Ensure rail carrier tabs are aligned with

chassis.

Fully tighten chassis screws.

Insert the end cap bracket into the rail assembly.

Andere Handbücher für Corbin Russwin PED5600 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Effeff 843G Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC135 Service-Handbuch

Assa Abloy

Assa Abloy SARGENT FIREGUARD 2499 Bedienungsanleitung

Assa Abloy

Assa Abloy SW60 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 5831 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7500H Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 1370 Bedienungsanleitung

Assa Abloy

Assa Abloy DC640 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FIREGUARD 12-2468 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1331 Bedienungsanleitung

Assa Abloy

Assa Abloy King 640 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 UniTrol Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton SafeZone 7110SZ Kurzanleitung

Assa Abloy

Assa Abloy Norton 9300BCH Bedienungsanleitung

Assa Abloy

Assa Abloy Crawford MCS-R Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4800 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung