Assa Abloy Norton SafeZone 7110SZ Kurzanleitung

Copyright © 2010, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9371-0081-020 (01-14)1Requirements:Units are handed. Hand of unit and hand of door must be the same.All dimensions shown in inches (mm).Door must be hung on ball bearing butt hinges or ¾” (19) offset pivots.Door thickness must be 1-3/4" (44) to 2-1/4" (64).Door must swing freely through the entire opening and closing cycle before beginning the installation procedure.Frame face must be a minimum of 2" (51).Ceiling clearance must be a minimum of 3 -1/2" (89) for push side application or 4” (102) for pull side application. See pages 3 and 7 for templates.Power input to unit must be of the same voltage as that stated on the unit.Unit to be mounted on interior of building in dry environment, maximum humidity of 95%.See NFPA70 for wiring requirements and NFPA72 for alarm system requirements.Pull Side Applications with Slide Track(7110SZ, 7150SZ)(see page 7 for template)Push Side Applications with Double Lever Arms(7120SZ, 7130SZ)(see page 3 for template)Item No.Description1 Track (Pull Side)2 Cover3 Track Arm (Pull Side)4 Double Lever Arm (Push Side)3124• Allen wrench set (inch)• Flat blade screwdriver (potentiometer & terminal size)• Screwdriver (Phillips size 2)• Tape rule • Power drill • Center punch • Wire stripper

Tools required:

Use screw pack and hardware provided to mount operator.

Table of Contents:

General Information...................2Push Side Template...................3Push Side Installation..............3-5Closer Adjustments...................6Pull Side Template.....................7Pull Side Installation.................7-9Closer Adjustments...................10Electrical Connections...............11Sensor Info and Set-up........12-13Troubleshooting.........................13

ASSA ABLOY

®7100SZ Series SafeZone Installation and Instruction ManualPatent Pending

ASSA ABLOY

80-9371-0081-020 (01-14)2General InformationIncluded with 7110SZ and 7150SZIncluded with 7120SZ and 7130SZ7120 ArmAssembly(7701-1A)7130 ArmAssembly(7701-1B)Arm Screw(7701-MAS)Component LayoutCertificationsUL228, UL10BCoverLH = 7100CLRH = 7100CRCloser/Holder Unit Assembly"X" = Power Size: 3, 4 or 5Pull Side: 711XUI24L 711XUI24RPush Side: 712XUI24L 712XUI24RBackplateSensorPower Supply(120V units only)BackplateMtg Screw (4)Cover MtgScrew (6)Test/Power SwitchTrack End Cap (2)Slide Assembly(7100SLD)Track Cover7110 Main Arm (7110-1A)Slide Track(7100-1T)7150 Main Arm, Handed(7150-1L: Left Hand 7150-1R: Right Hand)Track MtgScrew (2)Cushion StopAssembly(7100CB)NOTE: Optional remote for Advanced Settings(sensitivity, door controlmode) if required.(7100REM)

9/32” (7 mm) thru;3/8” (9.5 mm) dia. x3/8” (9.5 mm) deep ondoor opposite to closerStandardOptionalThrough-bolts andgrommet-nutsAllPreparation for FastenersDoor or FrameFastenersDrill-Sizes1/4” - 20 machinescrewMetal Pre-Drill: 9/64 hole Sleeve nuts andbolts(Shoe screws only)HollowMetal9/32” (7 mm) through;3/8” (9.5 mm) door faceopposite to closerAluminumor Wood3/8” (9.5 mm) through

Self drilling screw(Track screws only)

Drill: #7 (0.201” dia.)Tap: 1/4” - 20

Metal

Self drilling screw(Closer mountingscrews only)

Metal

Pre-Drill: 3/16 hole

ASSA ABLOY

80-9371-0081-020 (01-14)37120SZ, 7130SZ: Double Lever Arm (Push Side)Operator Mounting2Prepare FrameRight Hand Reverse - RHRLHR - Left Hand ReverseCeiling Line2(51)3-1/2(89)MinMin

Use of an auxiliary door stop, by others, is required for these applications.

Left Hand Door - LHRH - Right Hand DoorHingeEdgeOfDoorHinge or PivotDrill #7; Tap 1/4-2019-3/41-3/4(44.5)1-5/8(41.3)C4(101.6)11-1/4(285.8)(501.7)For ConcealedWiring Only7/8(22.2)DIATHRU11/16(17.5)5/16(7.9)ALeft hand door shown, right hand opposite.All dimensions shown in inches (mm).Install two screws in the key slot locations leaving 1/8" gap between screw head and frame as shown (a).C1/8"B1Top of Door Frame Soffit1-3/4(44.5)7/8(22.2)Frame

Model

Door OpenAngle

Dim “A”

Dim “B”

Reveal

Inches

(mm)

Inches

(mm)

712X SZ

100° Max.

5-7/8

149.2

13-3/8

339.7

2-3/4” - 7”

180° Max.

3-1/8

79.4

10-5/8

269.9

2-3/4 - 4”

165° Max.

4” - 7”

713X SZ

180° Max.

4” - 7”

ASSA ABLOY

80-9371-0081-020 (01-14)4Operator Mounting3cCbHang closer bodyby key hole slots (b) and slide closer toward hinge to capture screw heads (c).Operator Mounting4dCInstall remaining mounting screws through back plate and tighten all four screws (d). Pull wiring through holes (if concealed wired).Arm Shoe Mounting5Mount closer arm shoe to door face as shown.CFor Concealed Wired Only(If surface wired, see page 11)!

ASSA ABLOY

80-9371-0081-020 (01-14)5Attach Arm36Preload Closer Spring37Arm Screw(7/16” Drive)MainArmCloser Spring Adjustment3811/16" Wrench+Closing ForceWeaker

PinionFlat ArmMarkAlign the pinion flat withthe letter "S".Slowly increase closer power until door closes consistently. NOTE: A closer set to the ADA required 5 lbs opening force may not be strong enough to close the door due to latching hardware, air pressure, or frame issues.!90°With the door closed and latched, rotate main arm until secondary arm is perpendicular to the door frame, then tighten adjustment screw as shown with 7/16” wrench.eeStronger

ASSA ABLOY

80-9371-0081-020 (01-14)6Closer Adjustments39+

1/8"HexKey

"B"Backcheck75°

1/8"HexKey

"P"BackcheckPosition75°90°Electrical Connections3See Page 11Attach Cover311Attach cover using screws provided.!Never Close backcheck valve completely!Do not remove valves from closer. Hydraulic oil will escape.10WeakerStrongerClosing Speed Controls• Valve "S" Controls Sweep Range from full open to 5°.• Valve "L" Controls Latch Range from 5° to closed. Opening Cycle• Valve "B" controls the strength of cushioning in Backcheck Range. NEVER close this valve completely – it is not to provide a positive stop.• Valve "P" adjusts the angle that back- check is felt in the open cycle."L"Latch0°5°

1/8"HexKey

"S"Sweep5°

1/8"HexKey

ASSA ABLOY

80-9371-0081-020 (01-14)77110SZ, 7150SZ: Track Mount (Pull Side)Operator Mounting2Prepare FrameCeiling Line2(51)4(102)MinMinLeft Hand Door - LHRight Hand Reverse - RHRRH - Right Hand DoorLHR - Left Hand ReverseTrack Mount Unit6(152.4)19-1/8(485.8)CHinge or Pivot3-1/4(82.6)3/4(19)For ConcealedWiring Only7/8(22.2)DIA THRU1-3/8(34.9)1-1/16(27)2314-1/2(368.3)(584.2)1-1/4 (31.8)7110SZ Standard Arm7150SZ Double Egress ArmSeriesDim "A"5/8 (15.9)Right hand door shown, left hand opposite.All dimensions shown in inches (mm).Install two screws in the key slot locations leaving 1/8" gap between screw head and frame as shown (a).aC1/8"11/8(3.2)Top of DoorFrame Soffit9/64 (3.6) Holes for track screwsA(44.5)1-3/47/8(22.2)*9/64 (3.6) Holes for track screws*Prepare holes for mounting per instructions on page 2. *Track screws areself tapping and are smaller than closer mounting screws*

ASSA ABLOY

80-9371-0081-020 (01-14)8Operator Mounting3Operator Mounting4Arm Mounting5Hang closer bodyby key hole slots (b) and slide closer toward hinge to capture screw heads (c).CInstall remaining mounting screws through back plate and tighten all four screws (d). Pull wiring through holes (if concealed wired).CFor Concealed Wired Only(If surface wired, see page 11)!Fully close Latch & SweepValves with 1/8" wrenchprovided.Mount closer arm to pinion square as shown.Use main arm to rotate pinionuntil flat is visible.RE-INSTALLHERELEFTHANDRIGHTHANDAttach arm with providedscrew and washer. Tighten arm screw with 5/32" Allen wrench.Attach Arm36

PINIONFLATLEFTHANDRIGHTHAND

Align the pinion flat asshown.!

*All views from floor looking upward*bcd

ASSA ABLOY

80-9371-0081-020 (01-14)91) Insert slider into track.2) Insert spring cushion stop on hinge side of track for 125°or less opening angle. !Do not use for openings greater than 125°!3) Insert end caps (both ends). 4) Secure track to door using provided screws.5) Snap on cover.Set Screwstoward hinge!If opening angle greater than 125°, spring cushion stop cannot be used and an auxiliary stop by others is required.Mount Track37Connect Arm to Track38Open door to maximum desired swing minus 5° and hold. Slide spring cushion stop assembly against slider assembly and secure to track using 5/64" or 2mm wrench.HINGESecure arm to slider assembly using 3/16"Wrench. Turn wrench counterclockwise to tighten.Open Latch & Sweep Valves with 1/8" wrench provided.ABCDECloser Spring Adjustment39Slowly increase closer power until door closes consistently. NOTE: A closer set to the ADA required 5 lbs opening force may not be strong enough to close the door due to latching hardware, air pressure, or frame issues.11/16" Wrench+Closing ForceWeakerStronger

ASSA ABLOY

80-9371-0081-020 (01-14)10Closer Adjustments310+

1/8"HexKey

"B"Backcheck75°

1/8"HexKey

"P"BackcheckPosition75°90°Electrical Connections3See Page 11Attach Cover312Attach cover using screws provided.!Never Close backcheck valve completely!Do not remove valves from closer. Hydraulic oil will escape.11WeakerStrongerClosing Speed Controls• Valve "S" Controls Sweep Range from full open to 5°.• Valve "L" Controls Latch Range from 5° to closed. Opening Cycle• Valve "B" controls the strength of cushioning in Backcheck Range. NEVER close this valve completely – it is not to provide a positive stop.• Valve "P" adjusts the angle that back- check is felt in the open cycle."L"Latch0°5°

1/8"HexKey

"S"Sweep5°

1/8"HexKey

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Norton PR1601BF Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FIREGUARD 12-2468 Bedienungsanleitung

Assa Abloy

Assa Abloy DC700 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 724 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 1370 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Kurzanleitung

Assa Abloy

Assa Abloy SARGENT Powerglide 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-C Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130-HU Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9540 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W73ER Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 843G Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy G-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 3828 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-S Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9510 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 8000 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung