Assa Abloy SARGENT FIREGUARD 2499 Bedienungsanleitung

!CAUTION:

1. DISCONNECT ALL POWER BEFORE INSTALLATION.

2. ALL WIRING TO BE PERFORMED BY QUALIFIED

PERSONNEL TO COMPLY WITH ALL APPLICABLE

LOCAL CODES.

3. MAXIMUM WIRE SIZE IS 18 AWG.

Left Hand Shown Right Hand Shown

1Use template on page 4. Drill and tap door for 12-24 machine screws and frame for 1/4-20 machine screws.

Prepare hole for conduit. Do not drill through channel, as damage will occur voiding warranty.

2 3

Install closer body to door with spring

power nut away from hinge.

Following local codes, attach cable or conduit to track. Secure

track to frame with electronics away from hinge with screws

provided.

Wire unit as shown on Page 3; install cover as shown.

With wrench on bottom spindle, rotate spindle approximately 45°. Use screw and washer to secure main arm to

top spindle with index mark as shown.

L. H. Door

Hinge

Closer, spindle,

washer, and screw

Index mark

on spindle

45°

R. H. Door

Hinge

Closer, spindle,

washer, and screw

Index mark

on spindle

45°

NOTE: AN AUXILIARY DOOR STOP IS REQUIRED AT HOLD OPEN

2499 FIREGUARD Closer-Holder Device

PUSH SIDE INSTALLATION INSTRUCTIONS

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE

For assistance, contact SARGENT at 800-810-WIRE (9473) or www.sargentlock.com

express written permission of Sargent Manufacturing Company is prohibited. A8198 Rev 4

Approved 2022-11-04

Adjust hold open angle by adjusting arm length:

Range of 85° to 110° is obtainable. A) Place slider in

hold-open setting, B) open door, C) insert slide insert

into main arm. Open door to desired hold-open

position and D) secure arms with 9/64” hex screw.

Main Arm

Slide Insert

To adjust holding

tension:

Insert 9/64” allen

wrench thru hole in

track end cap into cap

screw in spring

mechanism. Rotate

allen wrench for

desired tension.

Closing and latching speed:

Turn valves clockwise to slow down or counterclockwise to speed up door movement.

Backcheck:

Turn valve clockwise to increase or counterclockwise to decrease.

CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. NEVER USE THE BACKCHECK AS A DOOR STOP.

ALWAYS USE A DOOR STOP TO STOP THE DOOR.

Delayed action feature (optional):

When provided, turn valve clockwise to slow down or counterclockwise to speed up door movement.

Backcheck

Valve

Delayed Action

Valve (optional)

Closing Speed

Valve

Latching Speed

Valve

Latching Speed

Range

Closing Speed

Range

Delayed Action

Range

Back

Check

Range

NOTE: If adjustments are

ineffective, check

indexing from step 5

FINAL ADJUSTMENT AND REGULATING PROCEDURES

Install cover as shown.

Insert is removable.

Place in unused opening.

Increase

Decrease

5/8”

Adjusting Nut

express written permission of Sargent Manufacturing Company is prohibited.

Adjust power to allow door to close and latch

Adjusting door to close due to high draft conditions may exceed

ADA standards. Consult local ordinances when fire doors are involved.

Door Width

(inches) Exterior Doors Interior Doors

24 - 30 1 - 3 CCW 1 - 3 CCW

30 - 36 Factory Set Factory Set

36 - 42 1 - 4 CW 1 - 4 CW

42 - 48 7 - 9 CW 4 - 6 CW

Number of Turns of Spring Power Adjusting Nut

A8198 Rev 4

Approved 2022-11-04

express written permission of Sargent Manufacturing Company is prohibited.

INSTALLER: LEAVE INSTRUCTIONS WITH BUILDING OWNER

CAUTION

1. Disconnect all power before beginning

installation to prevent electrical shock

and equipment damage.

2. Installer must be a trained, experienced

service person.

3. All wiring must comply with

applicable local electrical codes,

ordinances and regulations.

4. Maximum wire size is 14AWG.

2-Pin Jumper SOL

120VAC Circuit Board 4-Pin

Jumper

Earth

(+)

(-)

Input

Power

Test Switch

Openings for surface

or concealed wiring

Terminal Strip for

Power Input Connection

Header for Solenoid

Connection

Fuse (PTO125V)

125V / 1/2A

STAND ALONE UNIT

(120VAC shown)

- Wire stand alone unit to appropriate power supply and fire

system.

- Refer to data sticker on back of hook-up box for proper input

power voltage and current specifications.

- Solenoid Connector must be attached to Header on circuit board

before hold open will function.

- Energize power supply. Current draw of .074Amps max per unit.

- Open door to hold open point. Door should hold open.

- Depress Test Switch. Door should close and latch.

- Test Switch is a momentary switch. Once released, hold open

should re-energized.

- Adjust closer spring power to insure proper latching. Wiring Diagram for Master to Companion

Companion Unit - 24v ONLY

(2499 / 9-2499)

Master Unit -120v or 24v Input

(12-2499)

To Solenoid

7 6 5 4 3 2 1

8 7 6 5 4 3 2 1

Field Wiring Provided by Others

Wire Nut or Splice Connector (Provided)

- Companion units are designed to work with 12- smoke detector

units.

- Wire companion unit to smoke detector unit as shown on wiring

diagram.

- Do not disconnect any existing wires on smoke detector unit’s

terminal strip.

- Energize power supply. Current draw of .074Amps max per unit.

- Open door to hold open point. Door should hold open.

- Depress Test Switch on master unit. Doors should close and latch.

- Test Switch is a momentary switch. Once released, hold open

should re-energized.

- Adjust closer spring power to insure proper latching.

A8198 Rev 4

Approved 2022-11-04

express written permission of Sargent Manufacturing Company is prohibited.

(227)

4-1/4

(108)

29-1/2

(749)

32-1/8

(816)

2-9/16

(65)

Bottom

of stop

3-7/8

(98)

2-7/16

(62)

(4) #12 x 3” Wood Screws

or #12-24 x 2-1/4” Flat head

machine screws

C Hinge: Butts, center hung

or offset pivots

(25)

Edge of

stop

Edge of

stop

2” Min

stop

2-3/16

(56)

1-1/2

(38)

1-1/2

(38)

5-15/16

(151)

NOTES:

1. Reinforced metal doors and frames per ANSI

A250.8 & SDI-100, 12 gauge recommended.

2. Left hand door shown, right hand opposite.

3. For narrow rail doors (minimum 3”), use 351-D

drop plate.

3-1/8

(79)

(305)

(486)

31-11/16

(8005)

30-9/16

(776)

(3) 1/4-20 x 2”

Flat head machine screws

(1) 1/4-20 x 5/8”

Pan head machine screws

1-1/8 (29) hole

for Conduit

(51)

A8198 Rev 4

Rev 3: 2-9/16 was 2-7/16 for closer vertical dim

Rev 4: 4-1/4 was 2-15/16 for closer horizontal dim

Approved 2022-11-04

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy RIXSON W73ER Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 2500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton SafeZone 7110SZ Kurzanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 855 Montageanleitung

Assa Abloy

Assa Abloy Norton PR1601BF Bedienungsanleitung

Assa Abloy

Assa Abloy 1370 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 843G Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5400 (A) Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7500H Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6011 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 Bedienungsanleitung

Assa Abloy

Assa Abloy King 70 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W50 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton 7500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy MAB 609 + AC593 Bedienungsanleitung

Assa Abloy

Assa Abloy SW60 Handbuch

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung