Assa Abloy Norton 5900 Series Kurzanleitung

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

5900 Series

Power Operator

Installation and Instruction Manual

Complies with the following: ANSI/BHMA A156.19, UL325,

UL10C, FCC, Part 15, Sub Part B, CSA C22.2 No. 247

Item No. Description

1 Back plate

2 Operator (5900MOT)

3 Main control unit (5900CM)

4 120VAC electrical power connection

5 Cover (5900COV)

6 On/Off/Hold open switch

7 Activation inputs

8 Cover cap

9 12/24VDC output for locking hardware

Door stop (5900DS)

WARNING: To reduce the risk of injury to person,

use this operator only with: Pedestrian Swing doors.

• Adjustable wrench

• Flat blade screwdriver (potentiometer & terminal size)

• Screwdriver (Phillips size 2)

• Tape ruler

• Torque wrench (up to 25lbf-ft)

• Power drill and set of drill bits

• Center punch

• Wire stripper

• #7 drill 1/4-20 tap (metal frame install)

Tools required:

Glazing Material: the glazing material for swinging doors shall comply with ANSI Z97.1

Use screw pack and hardware provided to mount operator.

ASSA ABLOY

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

Mounting

PUSH Side (5930)

7/8

(22)

3/8

(9)

LHinge or Pivot

11/16

(17)

12-9/16

(319)

For Concealed Wired

Units Only (2 Places)

1-11/16

(43)

7/8

(23)

12-11/16

(322)

12-3/16

(309)

11-13/16

(299) 10-15/16

(278)

9-11/16

(246)

9-1/16

(230)

18-1/8

(461)

18-1/2

(470)

1-1/2

(38)

3/8

(10)

Sex Nuts

(2 Places)

Frame

Door Door

Stop

1/4-20 Machine Screws or

#14 Wood Screws

(8 Places)

1/8

(3) *

Required for proper

installation.

Dia.

PULL Side: 5910 - Rigid Arm & Slide Track

LHinge or Pivot

1-7/16

(36)

1-5/8

(41)

1-1/8

(29)

12-11/16

(322)

12-3/16

(309)

11-13/16

(299) 10-15/16

(278)

9-11/16

(246)

For Concealed Wired

Units Only (2 Places)

(559)

(279)

9-1/16

(230)

18-1/8

(461)

18-1/2

(470)

Door

Frame

1/4-20 Machine Screws or

#14 Wood Screws

(8 Places)

1/8

(3) *

Required for proper

installation.

7/8

(23)

3/8

(10)

Sex Nuts

(3 Places)

Dia.

5950 - Double Egress Arm

Model

5910

5950

"A"

4-3/4" (121)

5-1/4" (133)

"B"

1-1/8" (28)

1-13/16" (46)

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

NOTE: Teeth must be properly aligned.

NOTE:

Door must be visible by person

operating activation switch(es).

Absolute maximum opening is 110°;

door stop is required to prevent damage

to door hardware or adjacent walls.

BANG

Step 1: Connect arm and adapter to operator first.

REQUIRED Torque = 25 to 27 ft-lbs. This can only be

achieved with a torque wrench.

Step 2: Connect arm to track last.

Connect arm adapter to operator.

Concave Surface (inner curve)

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

Technical Data

120VAC, 60Hz

max. 75 W

24 V DC, max. 400 mA

2 x T 6.3 AH 250 V

36-48" (914-1219 mm)

100-200 lb. (45-90 kg)

Push arm: 80° - 110°, with reveal 0 - 7"

variable between 3 - 6 seconds

Power supply:

Power consumption:

Auxiliary voltage:

Internal control fuse:

Door width:

Electromechanical locking

device Selectable: 12V DC, max. 500 mA / 24 V DC,

max. 250 mA

Door weight:

Door opening angle:

(0 - 178 mm)

Pull arm: 80° - 110°, with reveal 0 - 1/8"

(0 - 3 mm)

Opening time (0° - 80°):

Closing time (90° - 10°):

Hold open time: 1.5-30 seconds (A.D.A. 5 seconds min.)

Ambient temperature: -4 °F to +113 °F (-20 °C to +45 °C)

Relative humidity

(non-condensing)

Max. 85%

Notes: Input connections - torque to 4.8 in/lbs (.55nm)

Permanent wiring is to be employed as required by local codes.

Any unused conduit holes must be plugged with provided covers.

Activation devices: push plates, access control, mats, etc.

1/2" Threaded

Conduit Hole

(4 locations)

Right hand push application shown

Line Voltage (120VAC)

(Field Wiring)

Line voltage circuit & low voltage circuit

must be in separate conduits.

Plug Unused

Holes With

Provided Covers

Low Voltage

(Field Wiring)

Strain Relief

Suitable strain relief must be provided upon

installation if the conduit bracket is used; strain

relief is to be provided by the installer.

Activation Device

Locking Device +vdc

Locking Device -vdc

Class 2 Supply 24 VDC

Use Copper Conductors Only

Com 120vac

Ground

HOT 120vac

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

Main Control Unit

Note: Arm can be changed in the field by following these

steps:

• Switch power off

• Switch power on

1 6

SPTE POAS

PAG

MAT

SOS

ARM1

ARM2

(+) 24VDC (0.4amp) - used with terminal 1 (for accessories)

HOT

5 s

1.5 s

LOUT Lock-out for OPD (–)

On/Off/Hold Open switch

Synchronizing of double doors (Master & Slave Cable input)

Motor

OPD Onboard presence detection (incl. 24 V, LOUT and

LRN Teach button

OPD Onboard presence detection

XIMP N/A

GND (-) 24VDC

PAG

MAT

SOS

PUSH

Spring

tension

Opening speed

Closing speed

Closing force

Hold open time

LED = Error

Main

Control

Board

30 s

2 3 4 5

CLTQ

CLSPOPSP

3 4 5

Power assist

Push & Go

Safety Mat (By others)

Stop on Stall

Arm System Setting

(see below)

Encoder

IMP Activation Switches

Dip switches shown

in Off position

PULL

Figure 1

Figure 2

• Select arm configuration on the DIP-switches (See Fig. 2)

Safety Impulse)

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

Auxiliary Control Board

+24 V DC

O/C

GND

–

0.5 s

0 s

Not Used

Latch Speeda)

Lock Releaseb)

Fail Secure - OFF / Fail Safe - ON

12 V shown (OFF) / 24 V (ON)

Potentiometer for opening delay

Toggle/Executive function (15 minutes maximum hold open)

Ground

12V DC max. 500 mA / 24 V DC max.

250 mA, see DIP-switch No. 1 below

Not Used

a) The “latch speed” complies with the ANSI/BHMA 156.19 requirements.

Position OFF: Smooth closing

Position ON: Faster, more powerful latch

b) Pulls door closer to the jamb to free latchbolt. If the switch is set to ON, the “lock release”

is active during the opening delay time set by the potentiometer. For “pair of doors”

3 4 5

345

3 s

2 3 4 5 6 7 8 9 10 11 12 13

installations, the “lock release” works in sequence; master then slave.

N/A

shown in

Off position

NOTE: If auxiliary contacts are

required, specify optional relay logic

module (part # 5900RLM).

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

Operation Set-Up

1. Close the door.

2. Set the potentiometer SPTE to 0°.

4. Switch the electrical power to ON position (the operator will find its closed position).

5. Open the door to required position by slowly turning the potentiometer SPTE on the

main control unit, clockwise.

0°

SPTE

0°

SPTE

3. Loosen the door stop arm and remove.

a.Door stop arm

b.Fixing screw

c.Stop block

d.Fine-adjustment screw

NOTE: Absolute maximum opening is

110°; door stop is required to prevent

damage to door hardware or adjacent

walls.

BANG

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

6. Mount the door stop arm on the spline (see figure a), as close as possible to the stop

block (figure b). Fine-adjust if necessary with the screw on the stop block (figure c).

a b c

0°

SPTE

Auto-teach – automatically sets backcheck and latch

This procedure is performed by pushing the Teach button (LRN). There will be a 2

second delay before door starts.

Note: Before the teach procedure starts, make sure that the door has been properly

closed.

•If any of the parameters “Spring tension” (SPTE), “Closing force” (CLTQ)

and “Lock release” (DIP-switch No. 3 on auxiliary control board) are changed

after teaching, repeat teaching procedure.

•Operator can be taught with activation units and locks connected.

•The backcheck will be automatically adjusted to 10° and 1 second before

open position. The latch will be automatically adjusted to 10° and 1.5 seconds

before closed position.

10°/1 s

10°

1.5 s

LatchBackcheck

LRN

Warning! Remain clear of swing path of door,

as door may close rapidly. The door

has no safety during auto-learn cycle.

7. Close the door by turning the potentiometer SPTE to 0°.

Note: Activations are not accepted if SPTE is more than 0°.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

Double doors

For double doors, the master door must be taught first. The master door will open to the full open position

during the slave door teaching phase.

The doors can also be taught separately before connecting the sync cable (optional).

Operation:

Your 5900 Series Operator can be configured in two variations to meet the standards:

1. Push plates are provided to activate the operator. The door also can be used as a manual door.

2. Push to activate can be enabled. In this mode, your door is pushed (or pulled) 5° manually, and

then automatically opens to full open position.

If desired, overhead presence devices can be provided for an extra level of protection. These are not

required by current ANSI/BHMA A156.19 codes.

Opening:

When an opening signal is received by the control unit, the door is opened at the operator-adjusted opening

speed. Before the door is fully open at backcheck, it slows automatically to low speed. The motor stops when

the selected door opening angle has been reached. The open position is held by the motor.

If the door is obstructed while opening, it will either stall or stop which can be selected with a DIP switch.

* When stalling - the door will continue to try to open during the hold open time.

* When stopping - the door will, even if hold open time has not expired, close after 2 seconds.

Closing:

The door shall not close with a force greater than 40 lbf (177.9N) at the latch side of the closing stile. It shall

not close through the final 10° in less than 1.5 sec. When the hold open time has elapsed, the operator will

close the door automatically, using spring force and motor. The door will slow to low speed at latch check

before it reaches the fully closed position. The door is kept closed by spring power or extended closing force

by the motor.

Note: Operator should be adjusted for the slowest operation in accordance with Americans with Disabilities Act

(ADA) and ANSI/BHMA A156.19 Standards.

Recommended tools: spring force gauge and stop watch

Opening speed: 5 seconds or more

Closing speed: 3 seconds or more

Latch location: 10° or more

Latch speed: 1.5 seconds or more

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

80-9359-0001-020 (01-14) Rev 3

General adjustment

• Set the hold open time with the potentiometer on the main control unit.

• Teach operator while opening is set at maximum opening speed. Turn closing speed

(on potentiometer) counterclockwise to slow operator down.

• Connect the required activation units.

• Check that the installation complies with local or state requirements.

Reducing / Increasing the “Spring Tension” (SPTE)

• Loosen the door arm stop. Remove if fitted on the topside, slide down if fitted on

the bottom.

• Turn the potentiometer for spring tension (SPTE) clockwise until the door

opens to 45°.

• Loosen the drive arm fixing screw.

• Moving the door towards open position, reduces the tension, or:

Moving the door towards closed position, increases the tension.

• Tighten the drive arm.

• Turn the potentiometer SPTE to 0°.

• Open the door to required open position by turning the potentiometer SPTE clockwise.

• Mount the door arm stop as close as possible to the open door stop block, fine-

adjust with the fixing screw if necessary.

• Turn the potentiometer SPTE to 0°.

• Repeat "Operation Set-Up" steps on page 6.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600H Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-FMS-K Bedienungsanleitung

Assa Abloy

Assa Abloy MAB 609 + AC572 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW200i Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Pull Side Series Kurzanleitung

Assa Abloy

Assa Abloy Besam SP33-M Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130-HU Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX88 Betriebsanleitung

Assa Abloy

Assa Abloy King 70 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy UNION DoorSense 8755A Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Handbuch

Assa Abloy

Assa Abloy Adams Rite EX89 Betriebsanleitung

Assa Abloy

Assa Abloy DC700G-FT Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 2409 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7970DPS-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy CMD Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 UniTrol Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung