Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

FM575 01/23

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information go

to www.P65warnings.ca.gov.

Installation Instructions

PED4000/PED5000 Series Exit Devices

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Electrical Wiring and Wire Routing for:

• M91 Prefix (Latch Monitor Switch)

• M93 Prefix (Exit Trim Lever Monitor Switch)

• M92 Prefix (Push Bar Signal Switch)

• M97 Prefix (Electric Dogging)

• 910/A, 930/A, 903/A, 905/A (Electromechanical Wide Exit Trim)

PED4000/PED5000 Series Exit Devices

Installation Manual

with optional connections

2FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Note: The M92, M91, M97, 910/A, 930/A, 903/A, 905/A, and M93 options are combined into this one

instruction.

TOC Table of Contents

1 Function .........................................................................3

2 General Description................................................................. 3

3 Specifications ....................................................................3

4 ElectroLynx Connector System Notes ..............................................4

5 Wire Routing.....................................................................5

6 PED4000/PED5000 Series Device Installation and Wiring Overview................ 16

7 M91 Prefix (Latch Monitor Switch) - Exit Device to Frame Connection ............. 17

8 M93 Prefix (Trim Monitor Switch) - Exit Device to Frame Connection .............. 18

9 M92 Prefix Push Bar (Signal Switch) - Exit Device to Frame Connection............. 19

10 M97 Prefix (Electric Dogging) - Exit Device to Frame Connection................... 20

11 910/A, 930/A, 903/A, 905/A (Electromechanical Exit Trim) -

Exit Device to Frame Connection ...................................................21

12 Appendix A: Harness Wiring Reconfiguration.......................................23

Installation Manual

with optional connections

PED4000/PED5000 Series Exit Devices

FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

1Function

• The M92 prefix signal switch monitors the touch bar. When the rail is depressed or dogged, the switch is

de-activated.

• The M91 prefix latchbolt monitor switch provides positive indication of latchbolt extension or retraction

when the push rail is depressed, dogged or if the latch bolt itself is depressed.

• When the M97 PE series exit device is energized and the rail is depressed, it will continuously hold the push

rail down and latch in an unlocked (dogged) position. When the device is de-energized (or power is inter-

rupted), the latch will extend.

• 910/A, 930/A, 903/A, 905/A Electromechanical Trims

• M93 prefix signal switch monitors the outside lever. When the lever is rotated, the switch is deactivated.

2General Description

This instruction manual includes wiring instructions for all Premium Exit (PE) Series Electrified Exits Options to

ElectroLynx connector system. The correct wiring configuration must be selected depending on type and function

of the product being installed. Refer to table of contents to select appropriate wiring instruction for product op-

tions being installed. Options/prefixes can be combined and wired together, as ordered.

Caution: The DC voltage applied to the electromechanical exit trim must not exceed 30VDC. If the voltage

exceeds 30VDC the motor may be damaged.

3Specifications

Motor

Type: 12 or 24VDC, Intermittent or Continuous Duty

Current draw is 400mA inrush / 15mA continuous @12VDC / 24VDC

Caution: Disconnect all input power before beginning installation to prevent electrical shock and

equipment damage. All wiring must comply with applicable local electrical codes, ordinances and

regulations. Installer must be a trained, experienced service person.

Fail Safe Models: Fail Secure Models:

910/A without cylinder 930/A without cylinder

903/A with cylinder 905/A with cylinder

Electromechanical Exit Trim

M91 prefix (latch monitor switch)

M93 prefix (exit trim lever monitor switch)

M92 prefix (push bar signal monitor switch)

M97 prefix (electric dogging) Electromagnet current: 200mA @ 24VDC

M91, M93, and M92 switch contact rating: 1A max @ 30VDC

PED4000/PED5000 Series Exit Devices

Installation Manual

with optional connections

4FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

4ElectroLynx Connector System Notes

The system is designed to be installation friendly with quick connectors from the electric hinge

through the door to the rail. The only wiring required is to the loose wires on the pigtail harness

assembly on the frame side of the electric hinge.

Important: The plug and receptacle connectors are designed to mate and lock together as shown in

the figure. Plug the connectors into each other with the locking mechanism aligned as indicated.

Do not force connectors on any other way.

Plug

Locking mechanism

Receptacle

1. With new applications, a raceway harness with 8 and 4 pin connectors will be pre-installed inside door by ASSA

ABLOY door manufacturer when specified during the ordering process. Raceway harness kits are also available

for retrofit applications.

2. If door does not have a raceway harness with connectors, cut connectors off product, or consult factory for

raceway retrofit kit.

3. Wiring to pigtail harness is per facility wiring requirement. The rail, raceway, electric hinge and pigtail connec-

tor terminations and wire colors all match.

These notes apply to all of the following devices concerning the installation and wiring to the

ElectroLynx Connector System

Installation Manual

with optional connections

PED4000/PED5000 Series Exit Devices

FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5Wire Routing

PED4600

OVERVIEW

M91 Connection

Step 1. Install mortise lock. Route wire

as shown.

M93 Lever Monitoring

(if applicable)

M91 Connection

Electric Trim

(If applicable)

Step 2. Route trim wires as shown.

M93 Lever Monitoring

(if applicable)

Electric Trim

(If applicable)

Electric Trim

(If applicable)

M91 Connection

M93 Lever Monitoring

(if applicable)

Step 3. Install chassis and rail.

Make wire connections.

Step 4. Pull back excess wire

through rail. Route wires as

shown. Install wire clip.

Wire Clip

PED4000/PED5000 Series Exit Devices

Installation Manual

with optional connections

6FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

PED4800

OVERVIEW

5Wire Routing - continued

Electric Trim

(If applicable)

M93 Lever Monitoring

(if applicable)

M91 Connection

Installation Manual

with optional connections

PED4000/PED5000 Series Exit Devices

FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

Step 2. Route wires through chassis

as shown and secure chassis to door.

Step 3. Install rail. Step 4. Make wire connections.

5Wire Routing - continued

Electric Trim

(If applicable)

M93 Lever Monitoring

(if applicable)

Step 1. Route wires as shown and secure trim to door.

Step 5. Pull back excess wire

through rail. Route wires as

shown. Install wire clips.

PED4800

M91 Connection

PED4000/PED5000 Series Exit Devices

Installation Manual

with optional connections

8FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

PED4200

OVERVIEW

5Wire Routing - continued

Step 3. Pull additional wire slack through rail

from insert end and tuck latch bolt monitor (M91)

connection into chassis.

Step 2. Secure trim. Make M91 connection.

Step 1. Install chassis to rail.

Route wires through door as shown.

Electric Trim

(If applicable)

M93 Lever Monitoring

(if applicable)

M91 Connection

Installation Manual

with optional connections

PED4000/PED5000 Series Exit Devices

FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

PED5800

OVERVIEW

5Wire Routing - continued

Electric Trim

(If applicable)

M93 Lever Monitoring

(if applicable)

Electric Trim

(If applicable)

M91 Connection

PED4000/PED5000 Series Exit Devices

Installation Manual

with optional connections

10 FM575 01/23

part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact Corbin Russwin

1-800-543-3658 • techsupport.corbinrusswin@assaabloy.com

5Wire Routing - continued

M91 Connection

Electric Trim

(If applicable)

M93 Lever Monitoring

(if applicable)

Step 1. Route wires as shown and

secure trim to door.

Step 2. Install chassis (Section 4) and route wires

through chassis as shown.

Main Slide & Roller

Step 3. Install rail. Step 4. Make wire connections. Step 5. Snap trim jumper to clip

and route excess wire as shown.

Step 6. Tuck wire connections along side of

main slide. Pull back excess wire through rail.

PED5800

Andere Handbücher für Corbin Russwin PED5000 DB Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Sargent 2409 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-CS Bedienungsanleitung

Assa Abloy

Assa Abloy CloserPlus Ramp Norton XF460 Bedienungsanleitung

Assa Abloy

Assa Abloy besam PUSH-N-GO Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR1601 Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-CS Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7540ST Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Kurzanleitung

Assa Abloy

Assa Abloy Yale 6000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7900H-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Adams Rite EX76 Betriebsanleitung

Assa Abloy

Assa Abloy 332 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5900 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton SafeZone 7100SZ Series Kurzanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC6210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC340 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung