Assa Abloy Norton 9510 Series Bedienungsanleitung

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

Multi-Sized 1 thru 6

with Heavy Duty Non-Hold Open

Parallel Arms

9510 Series

Installation Instructions

Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

IMPORTANT: An improperly installed or incorrectly adjusted door closer may cause property

damage or personal injury; and will void product warranty.

To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.

Door closers must be securely fastened to a properly reinforced door and frame

with fasteners provided.

An auxiliary door stop, BY OTHERS, is required for this Installation.

TO DETERMINE

HAND OF

YOUR DOOR:

LEFT

HAND

DOOR

RIGHT

HAND

DOOR

Size of Door & Door Closer

Type

Installation Interior Exterior

In-swinging

Exterior

Out -swinging

Recommended

Closer Size

**Max.

Opening

Force

lbs/f

2 4' "

2 6' "

3 0' "

3 6' "

4 0' "

4 6' "

2 6' "

3 0' "

*3 6' "

*4 0' "

**NOTE: These forces are for standard templating with bearing type hinges and do not account for pressure differentials and draft.

Parallel

Arm

RHR LHR

BEFORE

INSTALLING:

ADA compliant closer: 9510.

The Americans with Disabilities Act (ADA) requires that doors having door closers

have an opening force not to exceed 5 lbf.

The door closer's power size adjustment feature may require adjustment to its

lowest setting to comply with ADA opening force guidelines.

Page 2

Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

Components: Figure 1

Plastic Cover

(Standard)

Screw Pack

Closer Mounting

Bracket

Closer

9500-AB

Angle Support Bracket

Heavy Duty Non-Hold Open

Page 3

Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

9/32” (7 mm);

3/8” (9.5 mm) dia. x

3/8” (9.5 mm) deep on

door opposite to closer

Standard

Optional

Through-bolts and

grommet-nuts All

Preparation for Fasteners Figure 2

Door or Frame

Fasteners Drill-Sizes

#12-14 Self-Drilling Screw Wood

(see Note) 3/16” (4.30 mm)

1/4” - 20 machine screw Metal Drill: #7 (0.201” dia.)

Tap: 1/4” - 20

Hollow

Metal

9/32” (7 mm) through;

3/8” (9.5 mm) door face

opposite to closer

Aluminum

or Wood 3/8” (9.5 mm) through

Aluminum

or Metal No drill required

Page 4

Note: Wood doors/frames: drill 1/8" (3.2) pilot hole when using Self-Drilling Screws.

Always consult door/frame manufacturer for fastener compatibility with the material of their door/frame.

Approved 2018-01-19

(50.8)

(25.4)

1-1/2

(38.1)

SEE MOUNTING SCREW

SPECIFICATIONS

NOTE: ANGLE SUPPORT MUST BE

DRILLED AND TAPPED IN THE FIELD

9500-AB DOOR

FRAME

9500-AB

ANGLE SUPPORT BRACKET

5/8

(16)

FRAME STOP

TOP OF DOOR

HINGE

PIVOT

DOOR

FRAME STOP

2-3/4

(70) 5/8

(16)

1-1/2

(38.1)

1/4

(6.35)

TYP.

15/16

(23.8)

3/4

(19) 1-3/8

(35)

Minimum Clearance

MOUNTING

BRACKET

(254)

(25.4)

3-1/16

(77.8)

1/2

(12.7)

Adp

(76.2)

4-3/4

(120.7)

(76.2)

3/8

(9.5)

MAXIMUM

OPENING Adp BApplication

90°

180°

7-1/2 (191)

3-1/2 (89)

11-5/8 (295)

7-5/8 (194)

27-3/4 (705)

23-5/8 (600)

Mounting Bracket Drop Plate Soffit Bracket

7-7/8 (200)

3-7/8 (98)

Clearance

9588 DROP PLATE

Mounting Holes (4)

HD Parallel Arm Template

Page 5

5/8

(16)

DOOR

FRAME

ARM

BRACKET

SPACER BLOCK

(When required)

NOTES:

• Check hand of door, see page 2.

• Right Hand Application Shown. Left Hand Opposite.

• Dimensions given in inches (mm). Do Not Scale Drawing.

• Closer must be installed mounted level to ensure

proper closer performance.

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

• Attach arm to door frame.

• Connect arm to closer. Using hex wrench provided, turn closing speed

and latching speed valves clockwise until completely closed. DO NOT

OVER TIGHTEN. Open door to approximately 60°. Using wrench on

underside of spindle, rotate spindle approximately 135° toward hinge

edge of door. Install arm on spindle at an approximate 90° angle to door.

Reopen CLOSING SPEED VALVE. Install and tighten 5/16 Hex Head

Arm Washer and Screw Assembly.

• Select angle of opening and use dimensions shown in template to locate

4 holes on door for Closer Mounting Bracket (or 4 holes for

optional drop plate) and 6 holes on jamb for arm bracket (2 holes for

optional angle support bracket).

For applications that are different from above, a separate template will

be supplied for door and frame preparation.

• Prepare door and frame for fasteners using "Preparation for Fasteners"

chart, Figure 2, Page 4.

• Fasten Closer Mounting Bracket to door. Fasten optional drop plate to

door, only if it is required for the door conditions.

• Install closer body with tube end TOWARDS hinge, with valves:

DOWN for Left Hand door / UP for Right Hand door.

ROO

SPINDLE

ARM

CENTERLINE

ROOD

90°

SPINDLE

ROTATED

135°

Rotate 135°

60°

DOOR

135°

WRENCH

90°

ARM

• Make closer adjustments using information on page 7, then install

closer cover.

Page 6

HD Parallel Arm Installation Sequence

LEFT HAND DOOR SHOWN BELOW

ALL ANGLES SHOWN ARE APPROXIMATE

Approved 2018-01-19

Interior Exterior

Swing

Exterior

Out

Swing

Size of Door

Equivalent

Closer Size

(Approx.)

2 4 (712)' "

2 6 (764)' "

3 0 (915)' "

3 6 (1067)' "

2 6 (764)' "

3 0 (915)' "

2 6 (764)' "

3 0 (915)' "

3 6 (1067)' "

4 0 (1219)' "

2-7

7-11

11-15

15-17

Spring Power

Adjustment

No. Full Turns

Clockwise

LATCHING

SPEED VALVE BACKCHECK

INTENSITY VALVE

CLOSING

SPEED VALVE

SPRING POWER ADJUSTER

(1/4 ALLEN WRENCH)"

SPRING POWER ADJUSTMENT CHART

Spring Power Adjustment

Size 1 thru 6 Adjustment See Chart

All 9500 closers are factory set at an approximate Size 3.

Adjust closer as necessary for door size using this chart.

Readjustment may be required to suit prevailing conditions.

Locate spring power adjuster from

Illustration below

Backcheck Intensity Valve

Factory preset for typical doors.

Turn valve COUNTER-CLOCKWISE to reduce backcheck

or CLOCKWISE to increase backcheck. (Backcheck should

be set to give a soft cushioning action, not a sudden stop.)

Latching Speed Valve

Factory preset for typical doors.

After closing speed has been obtained, turn latching speed valve

CLOCKWISE to SLOW latching or COUNTER-CLOCKWISE to

SPEED latching for last 2 to 5 of door travel." "

NOTE: Set combination of CLOSING and LATCHING speeds to

between 3 and 7 seconds Use of door by handicapped,

elderly or small children may require even greater

closing time.

Closing Speed Valve

Factory preset for typical doors.

To adjust speed of door closing from fully open to a position

2 to 5 from closed, turn Closing Speed Valve CLOCKWISE" "

to SLOW closing, COUNTER-CLOCKWISE to SPEED

closing.

Delayed Action Valve

Factory preset for typical doors.

Turn valve CLOCKWISE to SLOW closing, COUNTER-

CLOCKWISE to SPEED closing. Delayed action may be

adjusted from 20 seconds to 90 seconds, depending on

degree of door swing. Delay occurs at the beginning of the

door closing cycle from fully open down to 70°, where the

closing speed valve then begins its control.

Option

(1/8 Allen Wrench Provided)

Date Stamp

(on end of closer)

MM-YY

OPTIONAL

DELAYED

ACTION VALVE

MM = Month

YY = Year

Unit Adjustment

Page 7

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

ASSA ABLOY

Page 8

Installing Cover

Insert is removable.

Place in unused opening.

Plastic Cover

(Standard)

3000 Highway 74 East • Monroe, NC 28112

Tel: (877)- • Fax: (800)-338-0965974-2255

www.nortondoorcontrols.com

ASSA ABLOY

Approved 2018-01-19

Andere Handbücher für Norton 9510 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy SARGENT FM8700 Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 843G Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SW300 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 1331 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 POWERGLIDE Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5400 (A) Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FIREGUARD 2499 Bedienungsanleitung

Assa Abloy

Assa Abloy Rockwood OH200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5900 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton J1600 UniTrol Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7970DPS-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton SafeZone 7100SZ Series Kurzanleitung

Assa Abloy

Assa Abloy DC130 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung