Atdec AWM-AD Bedienungsanleitung

AWM-AD Page 1 of 4

Installation Guide

AWM-AD

Dynamic Arm

COMPONENT CHECKLIST

REQUIRED TOOLS

Dynamic

Monitor Arm

(x1)

VESA

head

(x1)

Screw

M4x25mm

(x4)

Screw

M4x16mm

(x4)

Screw

M4x12mm

(x4)

Spacer

(x4)

Security

screw

(x1)

4mm

allen key

(x1)

• Phillips Head Screwdriver

WEIGHT RANGE

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! This product is compatible with Atdec AWM Series products.

! The Dynamic Arm (AWM-AD) requires a Post Clamp (AWM-LC, sold separately) for installation on an AWM Post.

! The Dynamic Arm (AWM-AD) requires a Desk Base (AWM-LB, sold separately) for installation directly onto an AWM fixing.

! The manufacturer accepts no responsibility for incorrect installation.

0 - 9kg

(0 - 20lbs)

AWM-AD Page 2 of 4

1. Set arm rotation to 180° (optional)

2. Fit arm onto Base or Post Clamp (sold separately)

Note: Check the

arm rotation is

smooth after

tightening.

2.1 Push arm onto shaft. 2.2 Ensure arm is fully pushed onto shaft. 2.3 Tighten joint screw.

1.1 On the Base or Post

Clamp (sold separately)

Remove plastic sleeve.

1.2 Remove rotation ring. 1.3 Place rotation ring in the

desired position.

Post Clamp Ring Position

When setting post clamp rotation,

orientate the ring depending on what

post channel the arm will be attached

to. The tag on the ring should always

face towards the user.

180°

360°

Default

Position

Flipped

Position Tag

1. Press

2. Lift

3.2 Attach VESA head onto monitor with

provided screws.

3. Attach VESA head to monitor

100mm

75mm

100mm

75mm

Flush

Too long Too short

Spacer

5mm 12mm

3.3 Be sure to use correct screw length3.1 VESA mounting compatibility

100mm

75mm

100mm

75mm

Flush

Too long Too short

Spacer

5mm 12mm

Note: For other sizes, use a suitable

adaptor plate (sold separately).

Note:

Spacers may

be required

for curved,

recessed

or uneven

monitor

surfaces.

4. Mount monitor on arm

Monitor arm

4.2 Ensure that the VESA head sits ush within

the monitor arm. There should be no gap.

4.1 Insert VESA head into the monitor arm 4.3 Push the lever down to secure

it to the arm assembly

Gap No Gap

AWM-AD Page 3 of 4

5. Adjust tilt tension & install security screw

5.1 Use the allen key to adjust the tilt tension until the monitor

holds in a vertical position at the end of the arm.

Note: Support

monitor while

adjusting.

Tighten

Loosen

Tighten

Loosen

5.2 OPTIONAL security screw

Tilt the head upwards to install the optional security screw.

7. Tension gauge

7.1 When installing

multiple monitors

of a similar weight,

use the tension

gauge to make

installation faster.

1. Set up one monitor and

record the position of the

marker on the gauge.

2. When installing subsequent

monitors, pre-tension the

arm to the recorded amount,

then ne-tune the tension by

following steps 6.3 to 6.5.

Arm Tension Gauge

Marker

Heavier

Monitor

Lighter

Monitor

6. Adjust arm tension

6.1 To accurately set the tension of the arm, position

the monitor at 90 degrees

6.2 Use the allen key to adjust the arm tension to the weight of the

monitor. Follow steps 6.3 to 6.5 to set the tension.

6.3 If the monitor sags or falls down,

increase the arm tension by rotating

the screw clockwise.

6.5 If the monitor oats or hovers in all

positions the arm tension is balanced

and does not require further adjustment.

6.4 If the monitor springs upwards from the

bottom position, decrease the arm tension

by rotating the screw anti-clockwise.

Monitor Falls

(from top)

Increase Tension

Monitor ‘Floats’

(all positions)

Balanced

Monitor Springs

(from bottom)

Reduce Tension

90°

AWM-AD Page 4 of 4

8. Cable management

8.1 Plug cables into the monitor and

route the cables down the arm using

the cable hooks and clips.

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

See steps 8.2 to 8.4

8.2 Wedge cable into the central gap

and slide it down the arm.

8.3 The cable should slip into the arm cavity 8.4 Slide the remaining loose cable

from the central gap up the arm.

Important!

Ensure enough cable slack is

given in this area to allow for

movement of the monitor.

Andere Atdec Rack & Stand Handbücher

Atdec

Atdec AWM-W6 Bedienungsanleitung

Atdec

Atdec AWM-BT Bedienungsanleitung

Atdec

Atdec APA-B Bedienungsanleitung

Atdec

Atdec AF-M Bedienungsanleitung

Atdec

Atdec AWM-W35 Bedienungsanleitung

Atdec

Atdec AWM-A13 Bedienungsanleitung

Atdec

Atdec Spacedec SD-POS-VBM-B2B Bedienungsanleitung

Atdec

Atdec VISIDEC FOCUS MICRO Betriebsanleitung

Atdec

Atdec AF-AT Bedienungsanleitung

Atdec

Atdec VISIDEC FOCUS ARTICULATED ARM DOUBLE Betriebsanleitung

Atdec

Atdec AWM 460 Arm Bedienungsanleitung

Atdec

Atdec AD-TVC-45 Bedienungsanleitung

Atdec

Atdec AWM-A13 Bedienungsanleitung

Atdec

Atdec ADB-FS Bedienungsanleitung

Atdec

Atdec AWM-FC Bedienungsanleitung

Atdec

Atdec SYSTEMA SW6S Bedienungsanleitung

Atdec

Atdec AWMS-BT40 Bedienungsanleitung

Atdec

Atdec AWM-LTH Bedienungsanleitung

Atdec

Atdec VFS-Q Bedienungsanleitung

Atdec

Atdec AWMS-46W35 Bedienungsanleitung

Atdec

Atdec SD-AT-DW Bedienungsanleitung

Atdec

Atdec AWMS-2-LTH75-H Bedienungsanleitung

Atdec

Atdec AD-WM-5060 Bedienungsanleitung

Atdec

Atdec AV Cart 75 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung