Atdec SYSTEMA SW6S Bedienungsanleitung

SW6S

SW6SW

Component Checklist

Wall Channel (x1)

! IMPORTANT - Install Systema Wall Channel as per installation instructions.

! Refer to Systema Monitor arm or Monitor Spring Arm Installation Instructions for maximum load advice.

! The manufacturer accepts no responsibility for incorrect installations.

! The Systema Wall Channel is compatible with Systema Monitor Spring Arm: SS and with Systema Monitor Arms: SA13,

SA46, and SA71.

IMPORTANT INFORMATION:

Step 1. Check Components

Check what you have received against the component checklist and hardware above.

Nylon Anchor (x2)

Top Cap Screws

(x2)

Top Cap (x1)

SYSTEMA

Installation Instructions

Systema | 60mm Wall Channel

Step 2. Position Wall plate - Ergonomic Guidelines

Many experts believe that the extended use of any computer screen has the potential to cause serious injury to your eyes,

neck and back. This can be largely avoided by correctly positioning your display.

Viewing angle: Ergonomists recommend that the optimal position

of your display should be slightly below eye level. When looking at

the display’s centre the user should have a downward visual angle of

approximately 10°-20°.

Height: As a guide, the height (h) of your display should approximately

be as follows:

- Tall Male (Max): 560mm (22”)

- Short Male (Min): 368mm (14.5”)

- Tall Female (Max): 520mm (20.5”)

- Short Female (Min) 356mm (14”)

When used with the Systema Monitor Spring Arm, it is

recommended that the bottom of the wall channel is

positioned 50mm above the worksurface to facilitate use by

the largest range of people.

Distance: For visual comfort, a viewing distance (d) between 500mm

(20”) to 750mm (29.5”) is recommended.

10º -20º

50mm (2”)

Guidelines based on a

720mm (28.3”) high

worksurface

(h)

(d)

Systema Monitor

Spring Arm ‘SS’ Shown

Please refer to the

Systema range Technical

Specifications for

dimensional details

Tools Required:

• Power Drill

• 5.5mm (1/4”) Drill Bit

• 8mm (5/16”) Drill Bit

• Phillips Head Screwdriver

M6 x 50mm

Countersunk

Screw (x2)

Step 3. Install Wall Channel

Nylon

Anchors

8mm (0.3”)

holes

M6 x 50mm

Countersunk

Screw

Systema

Monitor Arm

or Monitor

Spring Arm

Top Cap

Screws

M6 x 50mm

Countersunk

Screw

Systema

Monitor Arm

or Monitor

Spring Arm

Top Cap

Screws

Top Cap

5.5mm (0.2”)

holes

Installation Complete

You are now ready to install your Systema Monitor Spring Arm.

Please refer to the Installation Instructions Included with these products.

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 26.03.14 ©

Masonry Timber Stud

SSS

SSW

Component Checklist

Systema | Monitor Spring Arm

VESA monitor headArm Assembly

! IMPORTANT - Install Systema Monitor Spring Arm as per installation instruction.

! This product supports a minimum load of 1.5kg (3.3lbs) and maximum load of 8kg (17.6lbs).

! The manufacturer accepts no responsibility for incorrect installation.

! Compatible with Systema Posts: SP10, SP40, SP75 and Wall Channels: SW6 & SW35.

IMPORTANT INFORMATION:

Step 1. Check Components

Check what you have received against the component checklist and hardware above.

Step 2. Mount Arm Assembly

M4 x 12/16/25mm (x4)

Black Phillips Head Mounting Screws

3/4mm Allen Keys

HARDWARE

Display Mounting Screws

Display Mounting

Spacers (x4)

M4 x 14mm (x1)

Silver Phillips Head

Security Screw

SYSTEMA

Installation Instructions

2.1 Remove Post Top Cap.

Existing Systema Post

2.2 Insert Arm Assembly into Channel

Note: Ensure Clamp

Head Lever is vertical

and unlocked.

Note: Squeeze and hold Clamp Head before

inserting into the channel on Post Assembly or

Wall Channel. Arm Assembly

Pole Assembly

2.4 Lock Channel Clamp at

preferred height.

‘Click’

Allen Key

Post Top Cap

Post Assembly

2.5 Insert Post Top Cap into Post Assembly.2.3 Move Channel Clamp to desired

height and ensure arm is supported.

Note: An Allen Key

may be stored in the

Post Top Cap.

Wall Channel

100mm

Spacers (may be required for

recessed and uneven surfaces)

VESA monitor head

Gap No Gap

3mm Allen Key

4mm Allen Key

Loosen

Tighten

Security Screw

Hole

Spring Tension

Adjustment

M4 x 14mm

Security Screw

Monitor head

screw

Arm Assembly

Screen

M4x12/16/25mm

Phillips Head Mounting Screws

100mm 75mm

75mm

+ Tighten Loosen -

Step 3. Install VESA monitor head

Step 4. Mount Display

4.1 Insert VESA monitor head into the receptacle in the Arm

Assembly.

4.2 Ensure that the VESA monitor head sits flush within the

Arm Assembly receptacle. There should be no gap.

4.3 Once the VESA monitor

head is sitting flush, push

the lever down to secure it

to the Arm Assembly.

4.4 OPTIONAL

Ensure the Monitor is supported,

then loosen the Monitor head

screw with the 3mm Allen Key

and tilt screen up before installing

the M4 x 14mm Security Screw

into the Security Screw hole.

Step 5. Adjust Spring Tension

5.1 To ensure the monitor will stay in position anywhere

within its range of movement, the spring tension on the

arm will need to be adjusted to suit the weight of the

monitor.

Note: Ensure the Lever is

flicked up before installation

onto the Arm Assembly.

3.1 Install VESA monitor head as shown.

Support the weight of the

monitor at a high position

(as shown) and tighten the

spring tension until you

feel the arm supporting the

weight of the monitor.

Note: Support

Screen when

adjusting tilt.

Cable Cover

Cable

6.1 Plug your cables into the

monitor and follow this cable

management system route.

6.2 Loop the cable

and push it through the

Forearm Cable Clip gap.

6.4 Push the cable up into the gap in the lower

arm Cable Cover.

6.5 Whilst maintaining pressure on the

cable, slide the cable into the groove and

follow it up.

6.6 Whilst maintaining pressure on the

cable, slide the cable into the groove and

follow it down.

6.3 At the Elbow, pull one

side of the clip down and

push the cable through

the gap.

5.2 Push the monitor down to

the bottom. If the screen bounces

back this may indicate too much

tension. Loosen the spring tension

1 turn at a time until no bounce

is observed.

Once adjustments have been

made, move the arm assembly

through the full range of movement

to ensure it moves freely and holds

its position.

Spring Tension Gauge

Red Marker

Step 6. Cable Management

Step 5. Adjust Spring Tension (cont.)

5.3 MULTIPLE ARM INSTALLATIONS

When installing multiple SYSTEMA products using

monitors of the same weight, observe the location of

the red marker on the Spring Tension Gauge and

set the tension to the same position on all arms.

Note: Ensure enough cable slack

is given to allow for movement.

Max weight: 8 kg.

Cable Cover Optional Cable Cover Positions

6.7 Under the Channel

Clamp, pull one side of the

clip down and push the cable

through the gap.

6.10 OPTIONAL (NOTE: Cable clips only come with SP40

and SP75 Posts or separately in SC4 accessory pack)

A. Push the cable down into the

Cab

le Clip.

6.9 OPTIONAL

A. Loop cable and insert into Cable Cover.

Step 6. Cable Management (cont.)

6.10 OPTIONAL

B. Insert one side of the Cable Clip into the Channel on the Post assembly or Wall

channel, before pushing the other side in.

Note: Choose 6.9 and/or 6.10 for your column cable management depending on your needs.

6.9 OPTIONAL

B. Push the Cable down into either side of the Cable Cover until it reaches the bottom.

6.8 OPTIONAL (NOTE: The Cable Cover shown,

only comes with SP40 or SP75 posts.)

To reposition the Cable Cover, pull it straight up and

out of the post and insert it into any of the available

slots.

10º - 20º

5º 15º

(h)

Post Cable Clip

3mm Allen Key

Installation Complete

Step 7. Adjusting the Display Bracket

Ergonomic Guidelines

Many experts believe that the extended use of any computer screen has the potential to cause serious injury to your eyes,

neck and back. This can be largely avoided by correctly positioning your display.

Viewing angle: Ergonomists recommend that the optimal position

of your display should be slightly below eye level. When looking at

the display’s centre the user should have a downward visual angle

of approximately 10°-20°.

Height: As a guide, the height (h) of your display should

approximately be as follows:

- Tall Male (Max): 560mm (22”)

- Short Male (Min): 368mm (14.5”)

- Tall Female (Max): 520mm (20.5”)

- Short Female (Min) 356mm (14”)

Distance: For visual comfort, a viewing distance (d) between

500mm (20”) to 750mm (29.5”) is recommended.

Tilt Angle: Angular adjustments to reduce reflection on your

monitor should range between 5° forward tilt to 15° backward tilt.

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 12.02.14 ©

No Allen Key necessary

Tighten

Note: Support Screen when adjusting tilt.

Loosen

Portrait/Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)

For a triple configuration Atdec recommends using:

Post Cable Cover Post Cable Cover

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atdec Rack & Stand Handbücher

Atdec

Atdec ADBS-2x1-17TC Bedienungsanleitung

Atdec

Atdec AWMS-2-4640-C Bedienungsanleitung

Atdec

Atdec AWM 710 Arm Bedienungsanleitung

Atdec

Atdec AWM-WS Bedienungsanleitung

Atdec

Atdec AD-TVAC-CM Bedienungsanleitung

Atdec

Atdec AD-TVAC-CM Bedienungsanleitung

Atdec

Atdec AWM-A71-B Bedienungsanleitung

Atdec

Atdec AWM-BT Bedienungsanleitung

Atdec

Atdec AWM-A13 Bedienungsanleitung

Atdec

Atdec AWMS-BT40 Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-H Bedienungsanleitung

Atdec

Atdec AWMS-46W35 Bedienungsanleitung

Atdec

Atdec Levitate L-PB Bedienungsanleitung

Atdec

Atdec AWM-W35 Bedienungsanleitung

Atdec

Atdec AWMS-2-BT75-FS Bedienungsanleitung

Atdec

Atdec VFS-Q Bedienungsanleitung

Atdec

Atdec AWM-W35 Bedienungsanleitung

Atdec

Atdec Spacedec SD-POS-VBM-B2B Bedienungsanleitung

Atdec

Atdec AF Series Bedienungsanleitung

Atdec

Atdec AWM-A46 Bedienungsanleitung

Atdec

Atdec AWM-BT Bedienungsanleitung

Atdec

Atdec AWM-A71 Bedienungsanleitung

Atdec

Atdec AF-M Bedienungsanleitung

Atdec

Atdec VISIDEC FOCUS MICRO Betriebsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung