Atlantic Calypso FS 172L Bedienungsanleitung

The energy ecient heat

pump water heater

Calypso

INSTALLATION

MANUAL

19 Feb 24

UIN 235818 A03 B 700U07382380

*Image for illustration purposes only

This manual is to be left with the end user as it includes

instructions for maintenance, troubleshooting, after sales

service, and is used as a service record. The products

included in this manual have been independently

conrmed to comply with BS EN 12897: 2016.

CONTENTS ...............................................................................................................3

WARNINGS ...............................................................................................................4

DESCRIPTION .......................................................................................................11

1. Technical Characteristics .............................................................................11

2. Declaration of conformity .............................................................................13

3. Safety instructions ........................................................................................13

4. Transportation and storage ..........................................................................13

5. Packaging contents ......................................................................................14

6. Handling .......................................................................................................15

7. Manual handling ...........................................................................................16

8. Dimensions ..................................................................................................17

INSTALLATION ......................................................................................................18

9. Installation ....................................................................................................18

10. Hydraulic connection ....................................................................................19

11. Air connection ..............................................................................................27

12. Electrical connection ....................................................................................31

13. Filling the water heater .................................................................................32

14. Initial start-up ...............................................................................................33

15. Installation parameters .................................................................................34

16. Vericationofcorrectoperation ...................................................................37

17. Commissioning checklist ..............................................................................38

18. Service record ..............................................................................................39

MAINTENANCE .....................................................................................................40

19. User instructions ..........................................................................................40

20. Maintenance ................................................................................................40

21. Troubleshooting ...........................................................................................45

22. After-sales service .......................................................................................51

CONTENTS

Warnings Description Installation Maintenance

INSTALLATION:

CAUTION: Heavy product, handle with care:

1/ Install the appliance in a frost-free room. The appliance

is not covered by the warranty if it is permanently damaged

as a result of overpressure caused by the expansion relief

valve being blocked.

2/ Ensure that the oor can support the weight of the

appliance lled with water.

3/ If the appliance has to be installed in a room where the

ambient temperature is constantly higher than 35°C, then

provide ventilation for this room.

4/ In a bathroom, do not install this

product in Zone 0, Zone 1 or Zone

2 designated areas. Any low voltage

equipment installed into zone 1 or

zone 2 needs a minimum rating of

IPX4. Electrical wiring can be routed through zone 2.

5/ This product is intended to be used at a maximum

altitude of 2,000 m.

6/ Place the appliance in an accessible location.

7/ Refer to the installation drawings in the Installation

chapter.

8/ The water heater must be xed to the oor (in accordance

with article 20 of EN 60335-1) using the xing system

provided for this purpose.

WARNINGS

Warnings Description Installation Maintenance

0.60 m

9/ The HPWH installation must be in accordance with

the relevant requirements of the Building Regulations,

IET Wiring Regulations and the Water Fitting Regulations

(England and Wales) or Water Byelaws (Scotland).

10/ Calypso is covered by Section G3 of the Building

Regulations (England and Wales) Technical Standard P3

(Scotland) and Building Regulation P5 (Northern Ireland).

Compliance can be achieved via a Competent Person

Self Certication Scheme or notication of installation to

the Local Authority Building Control Department. It must

be installed by a competent person as dened by the

relevant regulations. Manufacturers notes must NOT be

taken as over-riding statutory obligations.

11/ Calypso is factory tted with a temperature & pressure

relief valve that must not be used for any other purpose

or removed.

12/ Calypso is factory tted with an immersion heater with

thermal cut outs. Immersions without thermal cut outs

must not be tted.

13/ This product has been manufactured using many

recyclable materials, including the approved HCFC/CFC

free polyurethane foam insulation. At the end of its useful

life, it should be disposed of at a Local Authority Recycling

Centre, to maximize the products full environmental

benets.

Warnings Description Installation Maintenance

MAINTENANCE:

Modications should not be made to this product.

Replacement parts, including immersion heaters, should

be purchased from Atlantic , or agents approved by them.

Unvented hot water storage vessels need regular routine

checks, and these are detailed below. It is for this reason

that this manual must always be left with the Calypso.

It is essential that these checks be carried out at the time

of heat pump maintenance by a qualied installer:

1. Manually open the relief valves in turn, and check

that water is discharged from the valves and runs freely

through the tundish and out at the discharge point. Ensure

that the valves re-seat satisfactorily. (Note - the water may

be very hot).

2. It is important to check that the discharge pipework is

carrying the water away adequately. Check for blockages

etc. if it is not.

3. Isolate the cold supply to the cylinder. Remove the inlet

control valve. Inspect the mesh lter on the inlet side and

remove any debris.

4. Check the charge pressure in the expansion vessel and

re-charge if required

5. Re-ll the system and ensure that all relief valves have

re-seated.

6. The Benchmark Service Record should be updated at

each service.

Warnings Description Installation Maintenance

7. Check the water pressure downstream of the

combination valve is 3 bar in static condition.

The Registered Installer is responsible for the safe

installation and operation of the system. The installer must

also make his customer aware that periodic maintenance

of the equipment is essential for safety. Maintenance

periods will vary for many reasons.

Atlantic recommend a maximum of 12 months to coincide

with heat pump maintenance. Experience of local water

conditions may indicate that more frequent maintenance

is desirable, eg, when water is particularly hard, scale-

forming or where the water supply contains a high

proportion of solids, eg, sand.

After servicing, complete the relevant Service Interval

Record section of the Benchmark Checklist located on

the inside back pages of this document.

HYDRAULIC CONNECTION:

This unit is supplied with an inlet control group. The

pressure reducing valve is set at 3.0 Bar and the expansion

relief valve is set at 4.5 Bar. This must be tted to the

water inlet pipe in a frost-free environment.

The Inlet control group supplied with this product will stand

a maximum mains pressure of 16 Bar. We advise that if

the mains pressure is consistently above 6 Bar consider

tting another pressure reducing valve (PRV), and if the

mains pressure is greater than 9 Bar t another PRV.

Warnings Description Installation Maintenance

Adjustable PRV’s are available. The additional PRV’s

need to be tted upstream of the inlet control group and

in multiple occupancy sites may be tted as a whole site

solution.

The expansion relief valve can be coupled with the TPRV

discharge pipework prior to the tundish. This way any

discharge should run away out of the building.

Discharges from the expansion relief valve usually indicate

a fault which needs to be addressed. For example the

expansion vessel charge pressure is too low.

If the discharge is hot and continuous, turn the power o󰀨,

but do not turn o󰀨 the cold water to the appliance until the

discharge is cold.

Note: The discharge should stop by itself as the

discharge cools.

However, in both cases you must call the registered

installer / a suitably qualied, competent tradesperson,

advise them that you have an unvented cylinder and

request a maintenance visit.

DO NOT, at any time, tamper in any way with the safety

valves or overheat thermostats.

There is a port on the inlet control group which can be

used to connect the expansion vessel. In any case the

expansion vessel should be tted here or between the

inlet control group and the cylinder.

Warnings Description Installation Maintenance

The Calypso is supplied with a drain elbow. This should

be tted to the cold water supply connection to enable

draining the cylinder.

IMPORTANT - DRAIN DOWN PROCEDURE:

1. Switch o󰀨 the HPWH.

2. Open the nearest hot tap and run all hot water until

cold, then close it.

3. Close the incoming cold main at the stop tap

4. Hold open the pressure and temperature relief valve

until water stops discharging into the tundish and leave it

open

5. Open the cold taps starting from the highest point and

working down to the lowest tap, leaving them open

6. When the cold taps have stopped draining, open the

hot taps starting from the highest and working down to the

lowest tap

7. Open the drain cock and ensure the pressure and

temperature relief valve is held open until the cylinder is

empty

Note: The cold supply elbow c/w drain tapping must

be to the cold water tapping. A exible hose can then be

connected to the drain tapping. The cylinder contents

can be drained to the tapping level. This is adequate

for all servicing requirements. If the cylinder is being

disconnected and removed then it may be tilted to drain

any water remaining in the cylinder.

Warnings Description Installation Maintenance

ELECTRICAL CONNECTION:

WARNING: Do not attempt the electrical work unless

you are competent to do so.

Before removing the cover, ensure that the power supply

is switched o󰀨 to avoid any risk of injury or electric shock.

The electrical installation must include an all-pole cut-out

device (circuit breaker, fuse) upstream of the appliance

in accordance with BS 7671 Requirements for electrical

installations. The appliance requires protection which can

be provided by a 30mA Residual current device.

Please refer to the wiring diagrams on the back of

the cover.

Connection to ground is compulsory. A special terminal,

designated , is provided for this purpose. Ensure local

isolation is provided within 1m (Double check with the

commentor).

Warnings Description Installation Maintenance

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atlantic Boiler Handbücher

Atlantic

Atlantic CHAUFFEO VS 500L Bedienungsanleitung

Atlantic

Atlantic IAV 75 Bedienungsanleitung

Atlantic

Atlantic MP 025 F 220-2E-BL Bedienungsanleitung

Atlantic

Atlantic SWH 10A M-N1 Bedienungsanleitung

Atlantic

Atlantic Zeneo 50 Bedienungsanleitung

Atlantic

Atlantic Flat 30 Bedienungsanleitung

Atlantic

Atlantic CALYPSO VM Bedienungsanleitung

Atlantic

Atlantic CHAUFFEO Bedienungsanleitung

Atlantic

Atlantic CHAUFFEO VS 500L Bedienungsanleitung

Atlantic

Atlantic CHAUFFEO Bedienungsanleitung

Atlantic

Atlantic Ingenio VM 050 D400-3-E Bedienungsanleitung

Atlantic

Atlantic CORFLINOX 300 Kurzanleitung

Atlantic

Atlantic CORFIRST Kurzanleitung

Atlantic

Atlantic Corprimo Series Kurzanleitung

Atlantic

Atlantic Vertigo Steatite 30 Bedienungsanleitung

Atlantic

Atlantic ACI Visio Bedienungsanleitung

Atlantic

Atlantic 021116 Bedienungsanleitung

Atlantic

Atlantic Vertigo 30 Bedienungsanleitung

Atlantic

Atlantic STEATITE PREMIUM Series Kurzanleitung

Atlantic

Atlantic CALYPSO Bedienungsanleitung

Atlantic

Atlantic Square O'Pro 15 Bedienungsanleitung

Atlantic

Atlantic SWH 20H M2 Bedienungsanleitung

Atlantic

Atlantic Mileo Inox+300 Bedienungsanleitung

Atlantic

Atlantic O'Pro 272014 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung