Atlantic Vertigo 50 Kurzanleitung
9954 – 1049 NZ
Enamelled steel tank
INDOOR
INSTALLATION ONLY
25 Litre Model
40 Litre Model
65 Litre Model
80 Litre Model
DOCUMENTATION FOR
INSTALLATION AND OPERATION
VERTIGO
electric water heater
Important:
For horizontal installationonly
The Hot & Cold water outlet must
be at the side
2
Model
Max Power
output
/
(W) (Bт)
Voltage
/
(V~) (B)
Water
Connections
Model 30 (25L)
1000
230
½”
p. 2/3
p. 4
p. 5
Model 50 (40L)
2250
230
½”
p. 2/3
p. 4
p. 5
Model 80 (65L)
2250
230
½”
p. 2/3
p. 4
p. 5
Model 100 (80L)
2250
230
½”
p. 2/3
p. 4
p. 5
1
1.1
Ø10 min.
3
1.2
1.3
1.4
1.5
50 cms minimum
(Supplied)
PTR Valve
(850kPa)
Untempered
hot water
(Kitchen,
laundry)
Tempered water
50°C
(Bathrooms)
Cold water
main supply
Non-return and
Isolang Valve
Line
Strainer
Drain lines
Pressure
Liming
Valve
(350-500 kPa)
4
2
7.
Hydraulic connection
5
Warning
This device is not intended for use by persons (including children) with
physical, sensory or mental disability, or by persons lacking experience or
knowledge, unless they have received from a person in charge of their
safety adequate supervision or preliminary instructions on how to use
the device. Care must be at all times to keep children from playing with
the device.
Caution
Heavy item, handle with care
• Install the appliance in a room that is protected from frost. If the
appliance is damaged because the PTR valve safety device has
been blocked, it is not covered by warranty.
•
must be provided.
•
mounted in a suspended ceiling, under a roof or above living area.
Position the appliance where it can be accessed.
Make sure that the wall on which the appliance is
mounted can support the weight of the appliance when filled with
water.
•
•
•
•
This device is intended for use at a maximum altitude of 3000 m.
Ensure that the wall on which the appliance is mounted can
support the weight of the appliance.
When installed in a bathroom do not install in volume V1 or V2
6
Mandatory installation of a safety device in a frost free location (or any
other new device which limits the tank pressure) to 850 kPa according to
the nominal pressure, with a size of 3/4’’ on the input of the water heater,
respecting the local regulations .
Operate regularly the discharge of safety device to prevent scaling and
check that it is not blocked.
To drain the device switch o the power and the supply of cold water, open
the hot water faucets and manipulate the safety valve.
The pipes used must support 1 MPa (10 bar) and 100°C.
Cold Water Inlet
Cold water piping should be provided with a 350 – 500 kPa Pressure
Limiting Valve at the point of cold water connection to the water heater.
In addition to the Pressure Limiting Valve, it is a requirement of AS 3500.4
& NZBC G12 that both a Stop Valve and a Non Return Valve are installed
upstream of the Product.
No parts (stop valve, pressure reducer, etc.) must be placed between the
pressure limiting valve and the cold water inlet of the water heater, apart
from a copper pipe.
Note: Since limited water discharge from Pressure Limiting Valve is normal
in the heating operation, the discharge pipe needs be connected to
external drain.
Hot Water Outlet
Where a maximum hot water delivery temperature is specied by local,
state or federal regulations, a tempering valve shall be installed at the hot
water outlet, as required.
The included specied Pressure & Temperature Relief valve must be
installed as shown in the schematic. The PTR valve should be connected
to a drain point to accommodate discharge as a result of both water
expansion during heating and also pressure uctuations.
The supplied PTR valve must be tted with Teon tape - don’t use paste or hemp.
7
DN15 copper drain lines must be connected to the discharge pipe of the
PTR valve. The copper drain line must fall away from the ESWH and be
installed in a frost- free environment.
The termination point of a drain line must comply with the requirements of
AS/NZS 3500.4
WARNING: The Pressure Temperature Relief valve and drain line must not
be sealed or blocked.
Electric Connection
All electrical work must be carried out by a registered electrician and in
accordance with AS/NZ 3000.
The Atlantic ESWH must be lled with water before connection to a power
supply.
Switch o the power before removing the cover to avoid any risk of injury or
electric shock.
The installation must be equipped, upstream of the appliance, with a
bipolar cut-out device (fuse, breaker switch) respecting local regulations
(30 mA earth-leakage breaker).
Always connect the earth conductor of the cable to the earth ground wire or
connect the earth conductor to the appropriate terminal identied by the
symbol.
Thermal cut-out
All Atlantic ESWH are equipped with a thermal cut-out with manual resetting
which shuts o the power to the water heater if it becomes overheated.
If the circuit breaker keeps tripping,
a) Switch o the power before taking any further action,
b) Remove the cover,
c) Check the electrical connections,
3
FLAT 30
FLAT 50, 80, 100
safety device or the thermostat. Connect the power supply only via the
terminal.
replaced by an authorized agent. Failure to respect this clause invalidates
the warranty.
8
9
SETUP & OPERATION
-NEVER POWER THE WATER HEATER WITHOUT WATER: Models with an electric
heating element will be certainly damaged.
- Fill the tank completely. Before powering up, open the hot water taps, drain the pipes
in order to empty the air.
- Check the tightness of the tubes and of the flange seal under the plastic cover. In case
of leaking tighten moderately. Check the operating of the hydraulic components and of
the safety valve.
- Turn the power on. After 15 to 30 minutes, depending of the capacity of the device, the
water should drip from the drain. This is normal and due to the expansion of water.
Check connection leaks and seal. During heating and according to the water quality, hot
water tanks can make a bubbling noise. This noise is normal and does not indicate any
defect of the unit.
The water heater features a digital screen that allows choosing the running
mode (see. drawing section 4 page 10).
1/ Modeselection knob (Ref. A): Enables to choose the running mode.
2/ Operating modes:
FROST FREE Mode (Ref. B): Automatic regulation at frost-free temperature (7°C), in order
to reduce the electric consumption during the periods of absence of the user.
MANUAL Mode (Ref. C): User selects a hot water temperature up to 70°)).
Warning: this operating mode may increase the electrical consumption of the product.*
SMART Mod (Ref. D): Fully automatic operation of the water heater: after a learning
period, the product will adjust automatically the hot water temperature adapted to the user
consumption. This allows lowering of the electrical consumption.
BOOST Mode (Ref. E): Soft touch button to activate fast heating of the appliance. The BOOST
mode is automatically deactivated when full hot water is available.
Warning: no BOOST on FLAT 30
3/ Shower display (Ref. F):
Display of the quantity of hot water available. When a shower symbol is blinking,
this means that a shower is under production (heating in progress).
4/ Power indicator (Ref. G): This light appears when the water- heater is connected to power supply.
EN
10
TROUBLESHOOTING
When a malfunction occurs, the user interface of the appliance can display an error code.
Fau lt (L E D s tatus)
Meaning R emark
2 successive flashes of one shower sign,
3 sec. of pause, 2 successive flashes ...
2 successive flashes of 2 shower signs,
3 sec. of pause, 2 successive flashes ...
4 successive flashes of one shower sign,
3 sec. of pause, 4 successive flashes ...
Error 3 :
Probe fault
Change probe
Error 3 :
Probe fault
(Differenaon)
Error 9:
Relay or PCB fault Change PCB
4
A
B
C
D
E
F
G
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Atlantic Boiler Handbücher
Atlantic
Atlantic ONDEO SWH 30 M Bedienungsanleitung
Atlantic
Atlantic STEATITE PREMIUM Series Kurzanleitung
Atlantic
Atlantic VISIO Series Bedienungsanleitung
Atlantic
Atlantic CHAUFFEO Bedienungsanleitung
Atlantic
Atlantic MP 025 F 220-2E-BL Bedienungsanleitung
Atlantic
Atlantic CORFIRST Kurzanleitung
Atlantic
Atlantic CALYPSO Bedienungsanleitung
Atlantic
Atlantic Compact 100 L Bedienungsanleitung
Atlantic
Atlantic 10S/GTS+10 Bedienungsanleitung
Atlantic
Atlantic Calypso FS 172L Bedienungsanleitung
Atlantic
Atlantic SWH 10A M-N1 Bedienungsanleitung
Atlantic
Atlantic PECS P300 Bedienungsanleitung
Atlantic
Atlantic IAV 75 Bedienungsanleitung
Atlantic
Atlantic Flat 30 Bedienungsanleitung
Atlantic
Atlantic CORFLINOX 300 Kurzanleitung
Atlantic
Atlantic CHAUFFEO Bedienungsanleitung
Atlantic
Atlantic Zeneo 50 Bedienungsanleitung
Atlantic
Atlantic 021116 Bedienungsanleitung
Atlantic
Atlantic EXPLORER 200L Bedienungsanleitung
Atlantic
Atlantic SWH 20H M2 Bedienungsanleitung
Beliebte Boiler Handbücher anderer Marken
Kenmore
Kenmore 153.582400 Bedienungsanleitung
Applimo
Applimo Edel AIR Bedienungsanleitung
STIEBEL ELTRON
STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung
clage
clage E-Mini Series Bedienungsanleitung
Toyotomi
Toyotomi Oil Miser OM-180 Bedienungsanleitung
Bradford White
Bradford White EF Series Bedienungsanleitung
