Atlantic VERTIGO 821359 Betriebsanleitung

9954 – 1049 NZ

Enamelled steel tank

INDOOR INSTALLATION ONLY

MODEL 821359 25 Litre

MODEL 831159 40 Litre

MODEL 841258 65 Litre

MODEL 851240 80 Litre

DOCUMENTATION FOR

INSTALLATION AND OPERATION

VERTIGO

electric water heater

Important:

For Horizontal Installation Only

The Hot Water Outlet Must Be

At The Top

Model

Max Power

output

(W) (Bт)

Voltage

(V~) (B)

Water

Connections

Model 30 (25L)

1000

230

½”

p. 2/3

p. 4

p. 5

Model 50 (40L)

2250

230

½”

p. 2/3

p. 4

p. 5

Model 80 (65L)

2250

230

½”

p. 2/3

p. 4

p. 5

Model 100 (80L)

2250

230

½”

p. 2/3

p. 4

p. 5

1.1

Ø10 min.

1.2

1.3

1.4

1.5

50 cms minimum

1. Hot water tube

2. Safety relief valve

3. Funnel

4. Pressure reducer

recommended if pressure >

0,5 MPa (5 bar)

5. Stop valve

6. Drain to sewage

7. Cold water pipe

8. Dielectric union

FLAT 30

FLAT 50, 80, 100

GENERAL WARNINGS

This device is not intended for use by persons (including

children) with physical, sensory or mental disability, or by

persons lacking experience or knowledge, unless they have

received from a person in charge of their safety adequate

supervision or preliminary instructions on how to use the device.

Children should be supervised to ensure that they do not play

with the appliance.

This unit can be used by children of not less than 8 years and

people with reduced physical, sensory or mental capabilities or

without experience or knowledge if they are properly supervised

or if the instructions for using the device safely have been given

and if the risks are taking into account. Children must not play

with the device. Cleaning and maintenance must not be done by

children without supervision.

CAUTION!Heavy item, handle with care:

1. Install the appliance in a room which is protected from frost.

If the appliance is damaged because the safety device has

been blocked, it is not covered by guarantee,

2. Make sure that the wall on which the appliance is mounted

can support the weight of the appliance when filled with water,

3. If the appliance is to be fitted in a room or location where the

ambient temperature is higher than 35°C, provide sufficient

ventilation,

4. When installed in a bathroom, do not install the appliance in

volumes V1 and V2 (See fig.1.1, p.2). If the water heater is to

install above living space, fit a retaining tank with drain to the

sewer system. Place the water heater in a place with easy

access,

5. If PER pipes are used, the installation of a thermostatic

regulator on the output pipe of the device is strongly

recommended. It will be set according to the performance of

the material used.

6. Installation of a vertical or horizontal wall mounted device: To

allow the replacement of the heating element leave a free

space of 500mm between the tube ends and the wall or fixed

furniture.

7. Switch off the power before removing the cover, to avoid any

risk of injury or electric shock.

8. The installation must be equipped, upstream of the appliance,

with a bipolar cut-out device (fuse, breaker switch) respecting

local regulations (30 mA earth-leakage breaker).

9. If the supply cord is damaged, it must be replaced by a special

cord or assembly available from the manufacturer or the after

sales service.

10. Always connect the earth conductor of the cable to the

earth ground wire or connect the earth conductor to the

appropriate terminal identified by the symbol .

11. Mandatory installation of a safety device in a frost free

location (or any other new device which limits the tank

pressure) to 0.7 or 0.9 MPa (7 or 9 bar) according to the

nominal pressure, with a size of 1/2" in the input of the water

heater, respecting the local regulations

12. Operate regularly the discharge of safety device to prevent

scaling and check that it is not blocked.

13. Hydraulic accessories should not be located between the

safety valve and the cold water inlet. A pressure reducer (not

supplied) is required when the water supply pressure exceeds

0,5 MPa (5 bar) and will be fitted on the main supply.

14. Connect the safety device to an unpressurised outlet pipe

in a frost free location, with a continuous slope to evacuate

water during heating up or draining the water heater.

15. The pipes used must support 1 MPa (10 bars) and 100° C.

16. To drain the device: Switch off the power and the supply

of cold water, open the hot water faucets and manipulate the

safety valve. To drain under sink water heater disconnect the

hydraulic connections and return the device.

17. The products described in this manual are subject to

changes at any time to be in accordance with technology and

standards. The devices comply with Electromagnetic

Directive 2014/30/UE, Low Voltage Directive 2014/35/UE,

Directive 2011/65/UE for RoHS and Regulation 2013/814/UE

supplementing Directive 2009/125/EC for ecodesign.

18. This product is intended for use at a maximum altitude of

3000m.

19. Do not dispose your water heater in the garbage, but

hand it to a place assigned for this purpose (collection

point) where it can be recycled.

20. The instruction book of this product is available by

contacting the after-sales service.

INSTALLATION

1. PRODUCT MOUNTING See “General Warnings” N°.1 to N°.6

For product installation, refer to drawings section 1 page.2 and page 3.

2. HYDRAULIC CONNECTION See “General Warnings” N°.11 to N°.16

For hydraulic connection, refer to drawings section 2 page 4.

- It is necessary to clean the supply piping prior to the hydraulic connection. The connection to the hot water

outlet is to be carried out with a cast iron or steel sleeve or a dielectric connector, to avoid corrosion of the

pipe (direct contact iron / copper). The use of brass fittings is prohibited.

- Always install a new safety device on the cold water pipe of the water heater, which comply with the

standards (EN 1487 in Europe), with a pressure of 0.7 or 0.9 MPa (7 or 9 bars) according to the nominal

pressure, with diameter 1/2".

- Do not use the safety valve included in this packaging in France (home country and French

overseas)

3. ELECTRICAL CONNECTION

For electrical connection, refer to drawings section 3 page 5.

- The water heater can be connected and operated only on AC 230V. Connect the heater with a rigid cable

with conductors 2,5mm ². Use a standardised channeling (rigid or flexible conduit) until the calibrated

housing cover.

- Directly connect devices with a cable or plug. In France, a product with plug is strictly prohibited and cannot

be sold and installed.

- Always connect the earth conductor of the cable to the earth ground wire or connect the earth conductor to

the appropriate terminal identified by the symbol . This connection is compulsory for safety reasons. The

earth wire green - yellow must be longer than those of phases. The installation must be equipped, upstream

of the appliance, with a bipolar cut-out device (minimum contact distance of 3 mm fuse, breaker switch). In

the case where hydraulic connexions are in insulated material, electrical circuits shall be protected by a

differential circuit breaker 30 mA adapted to local standards.

Thermal circuit breaker (see drawings section 3 page 5): All our products are equipped with a thermostat with

thermal circuit breaker and manual resetting which cuts off the power supply to the water heater in case of

overheating. If the safety trips:

 switch off the power before taking any further action,

 remove the cover,

 check the electrical connections,

 reset the thermal circuit breaker

If the circuit breaker keeps tripping, replace the thermostat. Never short circuit the safety cut out or the

thermostat. Connect the power supply only via the terminal.

SETUP & OPERATION

- NEVER POWER THE WATER HEATER WITHOUT WATER: Models with an electric heating element will

be certainly damaged.

- Fill the tank completely. Before powering up, open the hot water taps, drain the pipes in order to empty the

air.

- Check the tightness of the tubes and of the flange seal under the plastic cover. In case of leaking tighten

moderately. Check the operating of the hydraulic components and of the safety valve.

- Turn the power on. After 15 to 30 minutes, depending of the capacity of the device, the water should drip from

the drain. This is normal and due to the expansion of water. Check connection leaks and seal. During heating

and according to the water quality, hot water tanks can make a bubbling noise. This noise is normal and does

not indicate any defect of the unit.

The water heater features a digital screen that allows choosing the running mode

(see. drawing section 4 page 5).

1/ Mode selection knob (Ref. A): Enables to choose the running mode.

2/ Operating modes:

FROST FREE Mode (Ref. B): Automatic regulation at frost-free temperature (7°C), in order to reduce

the electric consumption during the periods of absence of the user.

MANUAL Mode (Ref. C): User selects a hot water quantity (temperature between 50°C and 70°)).

Warning: this operating mode might increase the electrical consumption of the product.*

SMART Mode (Ref. D): Fully automatic operation of the water heater: after a learning period, the

product will adjust automatically the hot water temperature adapted to the user consumption. This allows

lowering of the electrical consumption.

BOOST Mode (Ref. E): Soft touch button to activate fast heating of the appliance. The BOOST mode is

automatically deactivated when full hot water is available.

Warning: no BOOST on FLAT 30

3/ Shower display (Ref. F):

Display of the quantity of hot water available. When a shower symbol is blinking, this means that a shower

is under production (heating in progress).

4/ Power indicator (Ref. G): This light appears when the water- heater is connected to power supply.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atlantic Boiler Handbücher

Atlantic

Atlantic Vertigo Steatite 30 Bedienungsanleitung

Atlantic

Atlantic ODYSSEO 2 Montageanleitung

Atlantic

Atlantic STEATITE PREMIUM Series Kurzanleitung

Atlantic

Atlantic CALYPSO VM Bedienungsanleitung

Atlantic

Atlantic CHAUFFEO VS 500L Bedienungsanleitung

Atlantic

Atlantic CHAUFFEO VS 500L Bedienungsanleitung

Atlantic

Atlantic SWH 20H M2 Bedienungsanleitung

Atlantic

Atlantic Mileo Inox+300 Bedienungsanleitung

Atlantic

Atlantic Ingenio VM 050 D400-3-E Bedienungsanleitung

Atlantic

Atlantic ODEO Bedienungsanleitung

Atlantic

Atlantic Corprimo Series Kurzanleitung

Atlantic

Atlantic Compact 100 L Bedienungsanleitung

Atlantic

Atlantic ACI Visio Bedienungsanleitung

Atlantic

Atlantic Square O'Pro 15 Bedienungsanleitung

Atlantic

Atlantic Steatite Cube O'Pro 15 S3S Bedienungsanleitung

Atlantic

Atlantic VISIO Series Bedienungsanleitung

Atlantic

Atlantic CORFIRST Kurzanleitung

Atlantic

Atlantic Calypso FS 172L Bedienungsanleitung

Atlantic

Atlantic TWH 200 Bedienungsanleitung

Atlantic

Atlantic 021116 Bedienungsanleitung

Atlantic

Atlantic Zeneo 50 Bedienungsanleitung

Atlantic

Atlantic PECS P300 Bedienungsanleitung

Atlantic

Atlantic 10S/GTS+10 Bedienungsanleitung

Atlantic

Atlantic Vertigo 30 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung