AUDAC WX802/OB Montage- und Bedienungsanleitung
PROFESSIONAL AUDIO EQUIPMENT
Outdoor Wall Speaker WX802/OB
User Manual &
Installation Guide
Outdoor
W
all Speaker
WX802/OB
AUDAC
1
Warning
Only use the correct amplifier output voltage and impedance. Exceeding these limits could
cause fire or other failures. Avoid explosions: do not use the speaker around gasoline, thinner
or other combustibles.
Only install the speaker in locations that can structurally support the weight of the speaker.
Not doing so may result in the speaker falling down.
Do not use any other method than specified to mount the speaker. If extreme force is applied
to the speaker, the speaker could fall down.
Attach a safety wire to the speaker when it’s mounted high above the ground. Failure in doing
so could cause the speaker to fall down for any reason.
Avoid mounting the speaker in locations exposed to constant vibrations. The mounting
points can be damaged by excessive vibrations, potentially causing the speaker to fall down.
Caution
Avoid electric shocks: switch off the amplifier power when connecting the speaker.
Avoid installing the speaker in locations exposed to solvents, acids, smoke and heaters, as
excessive exposure to these factors could result in speaker failure, fire or electric shocks.
Do not operate the speaker for an extended period of time at distorted sound. This could
cause (irreparable) damage to the speaker.
Do not stand or sit on, nor hang down from the speaker as this may cause failure of the
speaker.
Installing the WX802
Mounting the loudspeaker
The loudspeaker can be mounted both horizontally and vertically by means of the supplied
mounting bracket. For mounting the loudspeaker on the desired mounting location, the mounting
bracket should be removed from the loudspeaker. This can be done by loosening the screws on
either side of the loudspeaker. After this is done, the mounting holes should be indicated. For a
stable mounting of the loudspeaker it should always be fastened by two screws. The position of
the mounting holes depends of the mounting position, horizontally or vertically with a spacing of
248 mm in between. After this, the bracket can be mounted on the desired location.
Always use the proper fasteners depending of the mounting surface.
Once the bracket is mounted on the desired location, the loudspeaker can be fixed to the bracket.
2
Attention
To make sure that no rain or other liquids can enter the loudspeaker when mounted
outside, a special construction is provided at the inner side of the bass port. This
construction is only useful when the loudspeaker is mounted in the correct position.
When the loudspeaker is mounted in horizontal position, the loudspeaker must be
positioned with the “AUDAC” logo on the side standing upright (in readable position), but
when the loudspeaker is mounted in vertical position, the loudspeaker must be positioned
with the tweeter on the top side of the loudspeaker.
Connecting the loudspeaker
On the rear side of the WX802/OB is a special waterproof 5-pin connector provided. This allows
to connect the loudspeaker to the amplifier output. A special included connection cable should be
used. Always connect the white conductor of the connection cable to the COM output of the
amplifier and the black connection terminal to the positive terminal of the amplifier output.
Mind the polarity markings when wiring the loudspeaker cables.
Power settings
The power settings of the WX802/OB can be made by rotating the
waterproof connector on the rear side of the loudspeaker. On the cable
part of the connector is a white dot displayed. Depending of the
position of the white dot, the desired power can be selected. The
corresponding powers are shown on the sticker on the rear side of the
loudspeaker. The power / impedance of the loudspeaker can be set in 3
adjustable steps of impedance for 100V (60 Watt, 30 Watt, 15 Watt)
and 1 step for 16 Ohm standard low impedance applications.
1) 16 Ohm / 70 Watt
2) 60 Watt / 167 Ohm
3) 30 Watt / 333 Ohm
4) 15 Watt / 667 Ohm
When the loudspeaker is connected to 70.7V facilities, the power indicated in the table above
will be reduced to half the power, and when connected to 50V facilities, the power will be
reduced to a quarter.
When the desired power tap is selected, the loudspeaker is ready to be used.
3
Additional information WX802/OB
Technical specifications:
RMS Power 70 W
Max Power 140 W
Nominal Impedance 16 Ohm
Line transformer power tappings 167 Ohm / 60 W
333 Ohm / 30 W
667 Ohm / 15 W
Sound pressure 1W / 1m 89 dB
Sound pressure max W / 1 m @ 8 Ohm 108 dB
Sound pressure max W / 1 m @ 100V 106 dB
Frequency response -3 dB 60 Hz - 18 kHz
Frequency response -10 dB 50 Hz - 20 kHz
Cross-over frequency 2400 Hz
Horizontal coverage 110°
Vertical coverage 110°
Drivers 1” HF + 8” LF
Dimensions (W x H x D) 270 x 360 x 215 mm
Weight 7,5 Kg
Construction ABS
Accessories included Wall bracket
Colour Black
Ingress Protection IP55
Inhaltsverzeichnis
Andere AUDAC Sprecher Handbücher
AUDAC
AUDAC SPRING-FIT CENA306 Bedienungsanleitung
AUDAC
AUDAC WX502B Montage- und Bedienungsanleitung
AUDAC
AUDAC WS624 Bedienungsanleitung
AUDAC
AUDAC CELO8 Leitfaden
AUDAC
AUDAC CELO2D Leitfaden
AUDAC
AUDAC BASO10/B Leitfaden
AUDAC
AUDAC WXMK2 Series Leitfaden
AUDAC
AUDAC SPRING-FIT CENA812 Bedienungsanleitung
AUDAC
AUDAC CS75 Bedienungsanleitung
AUDAC
AUDAC ATEO M Series Bedienungsanleitung
AUDAC
AUDAC VEXO1A Series Bedienungsanleitung
AUDAC
AUDAC MBK523/G Bedienungsanleitung
AUDAC
AUDAC ASP20 Bedienungsanleitung
AUDAC
AUDAC CS75B Bedienungsanleitung
AUDAC
AUDAC MERO6 Leitfaden
AUDAC
AUDAC CS55 Montage- und Bedienungsanleitung
AUDAC
AUDAC CS85 Montage- und Bedienungsanleitung
AUDAC
AUDAC WMM630 Bedienungsanleitung
AUDAC
AUDAC WS500 Bedienungsanleitung
AUDAC
AUDAC BASO Series Leitfaden
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung