Audiovox Prestige Platinum APS 995 Bedienungsanleitung

Model APS-995

Owner’sManual

IMPORTANT !

In order to provide you with the highest level of security to your

vehicle, this system is equipped with selectable manual override circuitry. It is

possible that you will need to override you security system if the transmitter

becomes lost, or inoperative due to battery failure. Reading the sections on

"Manually Overriding Your System" is necessary to fully understand the procedure

required to enable your vehicle in such situations. In addition, the chart on the last

page of this manual has a section for the particular features and options installed

in your vehicle as well as the override method selected. Although the default

mode is "Valet Switch" operation, the system can be configured for "Custom

Code" operation for enhanced security. Confirm the override mode selected on

the last page of this manual, and familiarize yourself with the section on it's opera-

tion.

FEATURES :

w1 Two Way 3 Button Remote Control And 1 One Way 4 Button Remote Control

wSix Channel Code Learning Programmable Receiver

wExternal Superheterodyne Receiver Antenna

wSingle Or Two User Programmable W/Separate Control Outputs

wSingle Button Lock/Unlock or Separate Button Lock/Unlock or Both

wRemote Keyless Entry With Optional Access Guard (must have power door

locks)

wSelectable Manual Override Mode

wNew Enhanced Panic Feature (Any button other than unlock stops siren, no

change to the units state)

wSmart Disarm (If triggered, elect to shut off siren, or disarm entire unit )

wSelectable Automatic Timed Start Mode

wAdjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect

Off,CityMode)

wSafe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or

For R/S)

wRemote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds

To Engage)

wImproved Custom Code Override, User Selectable and Programmable

wProtected Push Button Valet/Override Switch

w7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming

wIntrusion Alert With Memory

wInstant Siren Activation

4 Button Remote Start Security System With

Plug-In Shock Sensor & Starter Disable

Page2

wStarter Disable Output

wAdditional Engine Immobilizer Output, (Optional Relay Required)

wTrue Last Door Arming (Hardwire Only)

wDefective Zone By-Pass

wDefective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)

w6 Tone Mini Siren (New AS-9903)

wCar Horn Output For Additional Alarm Response (Improved Timing To Mini-

mize RF Interference.)

wAdditional Negative Trigger Input (Hood & Trunk)

wRF Inhibit With Ignition On

wParking Light Flasher (Relay On Board)

wPlug In Dual Stage Shock Sensor (Pre-detect, Full Trigger, and “City Mode”)

wAudible Arm, Disarm, Defect, And Tamper Chirp Indications

wHeadlight Control Output

wIlluminated Entry Control Output

wActive or Passive Arming Selectable

wProgrammable Auto Lock On / Off

wProgrammable Auto Unlock On / Off/Drivers Door/All Doors

wProgrammable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec

L/ Dbl. U/L

wProgrammable Active or Passive Door Locks

wUser Programmable Permanent Chirp Delete

wOn Command RF Chirp Delete from Transmitter Or Selectable Through

Software

OPTIONS :

wRemote Trunk Release (must have electronic trunk release)

wRemote Keyless Entry (must have power door locks)

wMultiple Vehicle Capable

wRemote Power Window Roll Up

wRemote Garage Door Interface

CAUTION! Be certain that the vehicle is outdoors before using this or any remote

vehicle starting device. A running engine produces dangerous car-

bon monoxide fumes which can be harmful or fatal if prolonged expo-

sure occurs. DO NOT remote start the vehicle if it is garaged.

YOUR“ANTICODEGRABBING“TRANSMITTERS

The transmitters included with your new security system use the most advanced

and secure form of radio frequency transmission available on any current automo-

tive security system. Some of today’s sophisticated auto thieves use a device known

as a code grabber, which will receive and store the signal from your keychain

transmitter, and re transmit at a later time to disarm your system.

Your Keeloq Code Hopping transmitters will change their signal every time the

button is pressed, so when a thief grabs then retransmits your signal, the alarm

system

will not

respond.

Page3

If your transmitter button is pressed more than fifty times while it is out of range of

the vehicle (children playing with your keys), the transmitter will not operate when

you return to the vehicle, and will need to be re aligned to the receiver. To do this,

simply press button 1 two times within a one second time period. The system will

now respond to that transmitter each time a button is pressed.

NOTE: This system is custom configurable and can be set up to operate with a

number of options controlled from any transmitter button or button com-

bination. For reference, we will describe operation assuming that your

system is programmed for separate lock and unlock buttons. Also refer-

ence will be made to the icons as shown on the buttons below.

NOTE: Concerning the LCD based remote, where lock is mentioned, use button

#1, where unlock is mentioned, use button #2, where trunk/start is mentioned,

use button #3. The Red Button is used to acquire status of the system.

See "System Status" described later in this manual.

Consult your installation center if your system has been configured differently.

NOTE: Your system has the option of using a siren, the vehicle horn, or both for

the sounding device. Where the siren is referenced below, the horn or

both may in fact chirp, or beep.

ARMINGTHESYSTEM-ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and release button Lock/Arm button on the keychain transmitter.

þThe dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren sounds one chirp.

If the siren sounds 3 chirps, then you have left a door, trunk, or

hood lid ajar. Simply close the opened entry point to provide full

protection. If the siren did not sound when arming, then the chirps

have been turned off, and you should refer to the section titled

“ELIMINATING THE ARM / DISARM CHIRPS“ in this manual.

oDoors Lock - Optional

Note: If the optional Headlamp illumination feature has been added, and has been

selected for operation when arming, as an added convenience, the system

will turn on the headlights when the system is armed.

SILENT ARMING - ACTIVE (Must be activated during programming)

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and hold button the Lock/Arm button on the keychain transmitter for 2

seconds.

þThe dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren will not sound.

If the siren sounds 3 chirps, then you have left a door, trunk, or

hood lid ajar. Simply close the opened entry point to provide full

protection

oDoors Lock - Optional

Page4

Note: If the optional Headlamp illumination feature has been added, and has

been selected for operation when arming, as an added convenience, the

system will turn on the headlights when the system is armed.

ARMINGTHE SYSTEM-PASSIVE(AUTOMATIC)

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid,

and trunk lid.

þThe dash mounted LED begins to flash rapidly, indicating 30 second

passive arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle

will immediately suspend automatic arming, and the 30 second passive arm-

ing cycle will restart when all doors are closed. At the end of the passive

arming cycle;

þThe dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren sounds one chirp

If the siren did not sound when arming, then the chirps have

been turned off, and you should refer to the section titled

“ELIMINATING THE ARM / DISARM CHIRPS“ in this manual.

oDoors Lock - Optional

Door locking during passive arming is a selectable feature.

The alarm can be programmed to allow the doors to lock only

when arming using the keychain transmitter, and they

will not automatically lock during passive arming.

PROTECTIONWHILE THESYSTEMISARMED

þOpening any protected door, hood, or trunk lid will cause the alarm to

immediately sound. The alarm will continue to sound for 30 seconds,

then stop and continue to monitor all protected entry points. If the thief left

a door opened, the alarm will sound for six 30 second cycles, remain

armed and ignore that triggered zone.

þWhenever the system is armed, the red dash mounted LED indicator will

slowly flash. This serves as a visual deterrent to the potential thief. The

LED is a very low current bulb, and will not cause the vehicle’s battery to

drain, even when left unattended for extended periods.

þWhenever the system is triggered, the vehicle’s parking lights will flash for

the full 30 second alarm cycle, attracting visual attention to the vehicle.

þOptional - Whenever the system is armed, the vehicle’s starting circuit will

be bypassed. If the thief should choose to ignore the siren, the vehicle can

not be started.

þAny mild impact to the vehicle’s glass will cause the alarm to sound a

short series of warning tones.

þAny strong impact to the vehicle’s glass will cause the alarm to trigger for

the full 30 second alarm cycle.

Note: If the optional interior illumination circuit was installed, the interior light will

flash as well for the full 30 second alarm cycle.

Page5

DISARMINGTHESYSTEM

Note: If the optional 2 step door unlock circuit is installed, when the unlock transmit-

ter button is activated, the drivers door only will unlock, pressing the unlock

button a second time will cause all doors to unlock.

Note: If your transmitter has been configured with single button Lock/Unlock as

shown, to activate the all door unlock feature operate the Lock/Unlock button

a second time within 3 seconds of the first unlock command.

1. As you approach the vehicle, press and release the Unlock/Disarm button on the

keychain transmitter.

þThe dash mounted LED turns off.

The LED will start flashing rapidly, indicating that the system is

rearming automatically. Open any door to suspend the automatic

arming.

þParking Lights flash two times.

If the parking lights flashed three times, then the alarm was trig-

gered in your absence. Before turning the key on, examine the

LED to identify which zone was triggered.

þSiren sounds two chirps.

If the siren sounds 4 chirps, then the alarm was triggered in your

absence. Before turning the key on, examine the LED and refer to

the INTRUSION WARNING SIGNALS section of this manual to

identify which zone was triggered.

If the siren did not sound when disarming, then the chirps have

been turned off, and you should refer to the section titled “ELIMI-

NATING THE ARM / DISARM CHIRPS“ in this manual.

oDoors Unlock - Optional

o2 Step Doors Unlock - Optional

Note: If the optional Headlamp illumination feature has been added, and has been

selected for operation when disarming, as an added convenience, the sys-

tem will turn on the headlights when the system is disarmed.

SILENT DISARMING (Must be activated during programming)

Note: If the optional 2 step door unlock circuit is installed, when the unlock transmit-

ter button is activated, the drivers door only will unlock, pressing the unlock

button a second time will cause all doors to unlock.

Note: If your transmitter has been configured with single button Lock/Unlock as

shown, to activate the all door unlock feature operate the Lock/Unlock button

a second time within 3 seconds of the first unlock command.

1. Press and hold button the Unlock/Disarm button on the keychain transmitter for 2

seconds.

þRed dash mounted LED turns off.

The LED will start flashing rapidly, indicating that the system is

rearming automatically. Open any door to suspend the automatic

arming.

þParking Lights flash two times.

If the parking lights flashed three times, then the alarm was trig-

gered in your absence. Before turning the key on, examine the

LED to identify which zone was triggered.

Page6

þSiren will not sound.

If the siren sounds 4 chirps, then the alarm was triggered in your

absence.Beforeturningthe keyon,examinetheLED and refertothe

INTRUSION WARNING SIGNALS section of this manual to identify

which zone was triggered.

oDoors Unlock - Optional

o2 Step Doors Unlock - Optional

Note: If the optional Headlamp illumination feature has been added, and has been

selected for operation when disarming, as an added convenience, the system

will turn on the headlights when the system is disarmed.

WHILETHESYSTEMISSOUNDING

If during a triggered state, you wish to shut off the siren without disarming your security

system, simply press and release any transmitter button other than the Unlock/Disarm

button. This action will turn off the siren yet leave the vehicle fully armed and protected.

Thisfeatureisparticularlyusefulif you are awareofchildrenplayingnearyourvehiclethat

may accidently trigger your security system. In this case you can cancel the siren

sounding without disarming your alarm.

INTRUSIONWARNINGSIGNALS

This system will inform you if an intrusion attempt has occurred while you were away

from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the

parking lights will flash 3 times when disarming the system. Enter the vehicle and

observe the red dash mounted LED to identify which zone was triggered.

If the LED is flashing one time...pause...one time...pause...etc., then an intru-

sion attempt was made to the shock sensor, or an accessory triggering device

that may have been added to the system.

If the LED is flashing two times...pause...two times...pause...etc., then an

intrusion attempt was made to a hood or trunk pin switch that was added to the

system, or to a light activated entry point if the alarm was installed using the

voltage sensing feature.

If the LED is flashing three times...pause...three times...pause...etc., then an

intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory, and will only be

erased when the ignition key is turned on.

VALETSWITCH

The valet switch allows you to temporarily bypass all alarm functions, eliminating the

need to hand your transmitter to parking attendants or garage mechanics. When the

system is in valet mode, all alarm functions are bypassed, however the remote panic

feature and remote door locks will remain operational. In addition, the parking lights will

flash to indicate locking and unlocking. To use the valet mode, the system must first be

disarmed either by using your keychain transmitter, or by activating your personalized

manual override code.

1. Enter the vehicle, and turn the ignition key to the on position.

2. Press and hold the valet push-button switch until the dash mounted LED

turns on solid. The system will remain in the valet mode.

3. To return to normal operation, press and release the push-button switch any

time the ignition is on.

NOTE: Always remember to return the system to normal operation. This will ensure

that the vehicle remains protected at all times.

Page7

MANUALLYOVERRIDINGYOURSYSTEM:

USINGTHEVALET SWITCHMANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter.

This is necessary, since you will need the ability to operate your vehicle if the

transmitter is lost or its battery fails. If your system has been selected for Valet

Switch manual override as indicated on the last page of this manual, to bypass

the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the valet push-button switch.

The alarm system will stop sounding and enter the (bypass) mode. You can now

start and operate the vehicle normally.

Typically this override mode is used only if the transmitter has become inopera-

tive.

Programming Your Custom Override Code:

Unlike override switches easily found, and defeated, this security system allows

the consumer to program a personal override code, offering a higher level of

security. To take advantage of this option, programmable feature # 10 must be

selected for the Custom Code Option. Consult your installation center for

programming details. The system comes from the factory with a pre-programmed

override code of 11. To change this default override code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the valet/override switch, 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and

releasing the push-button switch from 1up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off

then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and

releasing the push-button switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by

flashing the LED, first indicating the 10ths digit, pause and then the units digit.

The unit will report the new code three times with a one second pause between

each code, then the system will begin arming. If the LED flash pattern

reports the previously stored code, the new code was not entered correctly. Please

repeat steps 1 through 7 above considering the following.

NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not

recognize a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert

back to the last successfully stored code.

Custom Code Programming Example:

To Change the code from the factory preassigned code of 11 to “52” you would do

the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence.

2. Turn the ignition switch to the on position.

3. Within 10 seconds, press and release the valet/override switch, 3 times.

4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

5. Within 10 seconds, begin to press and release the push-button switch to set

the tenths digit.

(As per the example, press and release 5 times to set the tenths digit to 5)

6. Within 10 seconds of the last press of the push-button, turn the ignition switch

off then on.

7. Within 10 seconds, begin to press and release the push-button switch to set

the units digit.

(As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position. Immediately observe the LED flash

pattern.

You will note the LED flashing five times, pause, and then flash two times, pause.

This pattern will be repeated three times indicating the new code (52) has been

accepted and stored in memory.

NOTE: If after step 7, the LED flashes a code other than what was just entered,

this indicates that the code has not been changed. You will have to repeat

steps 1 through 7 above being certain to note the following:

Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0

(Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert

back to the last successfully stored code.

MANUALLYOVERRIDINGYOURSYSTEM:

USINGTHECUSTOMCODEOVERRIDE

Assuming the override code programmed has not been changed, and the default

override code of 11 is in the system's memory.

1. Enter the vehicle and turn the ignition switch to the on position.

Note: The siren will sound.

2. Within 5 seconds, press and release the push-button switch 1 time.

3. Within 5 seconds, turn the ignition switch off then on.

4. Within 5 seconds, press and release the push-button switch 1 time.

5. Turn the ignition switch off then on and start the vehicle.

Note: If you have changed the programmed override code then substitute your

new code tenths for step 2 above, and units for step 5 above.

Page8

ELIMINATINGTHE NORMALARM /DISARM CHIRPS

As explained earlier in the manual, you can eliminate the chirps selectively any

time you arm or disarm the system simply by holding the ARM or DISARM button

for two seconds. If you find the normal arming and disarming chirps annoying,

they can be turned off permanently, eliminating the need to hold the ARM / DIS-

ARM button for 2 seconds. To do this,

1. Turn the ignition key on then off.

2. Within 10 seconds, press and release valet switch three times.

3. If the chirps were on before you started, then you will hear two chirps indicat-

ing they have been turned off.

If the chirps were off before you started, then you will hear one chirp indicating

they have been turned on.

NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator

and 3 chirp defective zone indicator will always operate. Since these are

important warnings to you that something has happened, they cannot be

eliminated.

REMOTEPANICOPERATION

The Lock or Unlock button on your keychain transmitter also functions as a panic

switch for use in emergency situations. To use remote panic,

1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or

more seconds. The alarm will immediately sound.

2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter

again for 3 seconds. If the button is not pressed, the alarm will automatically

stop after 30 seconds. Also if any transmitter button other than the Lock or

Unlock button is pressed and released, the Panic mode will be turned off

immediately. The normal function of this transmitter button will be suspended

during the Panic sounding period.

3. During the panic mode, the Lock and Unlock buttons can be used to lock and

unlock the doors, (if the option is installed), however once the unlock/disarm

button is pressed, the vehicle's starter inhibit device, (where installed) will be

disabled allowing the vehicle to start.

NOTE: While in the Panic mode, pressing and releasing the Lock or Un-

lock buttons will, if the option is installed, lock and unlock the doors respectively.

While in the panic mode, anytime the Unlock button is pressed, the panic feature

will continue for the allotted 30 seconds, however, the security system will be

disarmed allowing the vehicle to start.

R.F.SHOCK SENSORMODE SELECTION

The way in which your alarm system reacts to threatening vibrations, created by

attempts to enter the vehicle by breaking a window, is adjustable by the transmitter

immediately after arming. There are 4 modes of operation that can be selected

by the operator.

1. Normal Operation (default mode)

In this mode, any strong vibrations will cause the siren to sound (full

detect) for 30 seconds. Any lesser vibration will cause the siren to emit

about 6 short warn away chirps, (pre-detect).

2. Stage 1 (Omit pre-detect)

In this mode, the warn away chirps created by the lesser vibration will be

deleted. If strong vibration occurs, the siren will sound.

Page9

3. Stage 2 (Omit pre & full detect)

In this mode, both the pre-detect stage, and the full trigger stage of the sensor

are defeated. The unit will not react to vibration of any magnitude.

4. Stage 3 (City Mode)

In this mode, the pre-detect chirps will change from six pre-warning tones to

a full 10 seconds of warning chirps.

The full detect trigger duration will be reduced from 30 seconds to 15 seconds.

NOTE: Setting the stage of the shock sensor will be effective for one arming cycle

only. Once the system has been disarmed, the very next arming cycle will

cause the sensor to default to the normal operation stage.

To change or adjust the shock sensor, press and release the ARM button of you

keychain transmitter.

1.Within 2 seconds of arming, press and release the ARM button 1 time, to

defeat the pre-detect stage of the shock sensor. (The lights will flash and the

siren will chirp once.)

2.Within 2 seconds of step 1, press and release the ARM button 2 times, to

defeat the pre and full detect stages of the shock sensor. (The lights will

flash and the siren will chirp twice.)

3.Within 2 seconds of step 1, press and release the ARM button 3 times to

enter the "City Mode" of operation. (The lights will flash and the siren will chirp

three times.)

SAFETY(RedHandled )CONTROLSWITCH

The control switch allows you to temporarily disable the remote starting function

of your APS-995. To disable the unit, move the red handled control switch to the

off position.

The control switch also allows you to select between 2 hour start up and 4 hour

start up when using the automatic start up timer mode. The factory preset start up

time for this mode is every 4 hours. To select between 2 or 4 hour start-up timer:

1. Begin with the control switch in the on position

2. Turn the ignition switch on then off

3. Within 10 seconds, move the control switch off, on, off, on (2 switch cycles) to

select a 2 hour start timer. After 10 seconds expire, the parking lights will

flash and the siren will chirp 2 times confirming that the two hour start cycle is

set. Or, within 10 seconds move the control switch off, on, off, on, off, on,

off, on (4 switch cycles) to select a 4 hour start timer. The parking lights will

flash and the siren will chirp 4 times confirming that the 4 hour start timer is

set.

REMOTESTARTINGTHEVEHICLE

The APS-995 WILL NOT start the vehicle if any one of the following conditions exists:

1. The Vehicle Hood Is Opened.

2. The Gear Selector Is In Any Gear Other Then Park.

3. The Brake Is Depressed.

4. The Safety Control Switch Is In The Off Position.

WARNING! Be certain that the vehicle is outdoors before using this or any remote

vehicle starting device. A running engine produces dangerous carbon

monoxide fumes which can be harmful or fatal if prolonged exposure

occurs. DO NOT remote start the vehicle if it is garaged.

Page10

Andere Handbücher für Prestige Platinum APS 995

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox Prestige APS-15KB Bedienungsanleitung

Audiovox

Audiovox RO9801 Bedienungsanleitung

Audiovox

Audiovox Prestige AS-9256 Bedienungsanleitung

Audiovox

Audiovox APD-510 Bedienungsanleitung

Audiovox

Audiovox APS620 - Prestige Remote Start Bedienungsanleitung

Audiovox

Audiovox Pursuit Pro 9544FT3 Bedienungsanleitung

Audiovox

Audiovox Prestige 5BLCR Betriebsanleitung

Audiovox

Audiovox Prestige APS-25-CL Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9600 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-920 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-786T Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-8117 Bedienungsanleitung

Audiovox

Audiovox 5BCRCS Bedienungsanleitung

Audiovox

Audiovox APS996A - Prestige Remote Security System Bedienungsanleitung

Audiovox

Audiovox 5BCR Betriebsanleitung

Audiovox

Audiovox APS-95BT2 Betriebsanleitung

Audiovox

Audiovox Pursuit PRO-9900 Bedienungsanleitung

Audiovox

Audiovox PRO-9776i Bedienungsanleitung

Audiovox

Audiovox APS-20A Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9744WOS2 Bedienungsanleitung

Audiovox

Audiovox APS25CH - Car Prestige 2 Button Remote Security... Bedienungsanleitung

Audiovox

Audiovox Prestige APS-15R Bedienungsanleitung

Audiovox

Audiovox Auto Security AA-9300 Betriebsanleitung

Audiovox

Audiovox Prestige APS-35-CL Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung