Audiovox Pursuit PRO-9744WOS2 Bedienungsanleitung

Important! The PRO-9744 alarm system is configurated for many different

user preferences. Please read this entire manual to fully understand the

operation of your specific unit's installation.

MODEL PRO-9744WOS2

Owners Manual

Remote Alarm with

Selectable Pre-Load Features

-1-

2 Four Button Anti Code Grabbing Programmable Transmitters

6 Channel Code Learning Receiver

Remote Panic All Modes

Protected Valet/Manual Override

8 Function LED- Armed, Disarmed, Arming, Zone 1, Zone 2, Zone 3,

Zone 4, & Valet

Intrusion Alert With Memory

Audible Arm, Disarm, Defective Zone, and Tamper Indication

Instant Alarm Activation

Starter Disable

True Last Door Arming

Defective Zone By-Pass

Hard Wire Switch Sensing

On Command RF Chirp Delete

6 Tone Multi-Tone Siren (Option)

Multiple Vehicle Operation

On Command R.F. Audible Response Delete

R.F. Shock Sensor Delete (Optional Dual-Stage Shock Sensor required)

Active or Passive Arming

Active or Passive Door Locks

Ignition Control Door Lock On/Off

Ignition Control Door Unlock, (Drivers Door or All Doors), On or Off

Independent RF Headlamp Control

20 Second Headlight Illumination Arm Or Disarm, Both Or None

Panic On Lock Button Or On Separate Button

FEATURES & OPTIONS:

SELECTABLE FEATURES:

TRANSMITTER ICONS (Symbols):

The PRO-9744's 4 button transmitter has a replaceable membrane (button pad)

that uses icons to denote operation of your security system. The icons used are

a standard in use by the automotive industry. Their functions are described below.

LOCK: The closed lock symbol is the Lock and Arm button of your

transmitter. This function will allow the locking of the vehicle doors

(with optional door lock interface and power door locks), and the

arming or setting of the security system.

UNLOCK: The open lock symbol is the Unlock and Disarm button of

your transmitter. This function will allow unlocking of the vehicle's

driver door, or all doors, (with optional door lock interface and power

door locks), dependent on the way the control module is programmed.

This button will also disarm the security system if it is armed.

TRUNK: The open trunk symbol on the transmitter button will operate

the vehicle's trunk release, (option, with existing power trunk, relay

required). Press and hold this button for two seconds to activate the

trunk release option.

HEADLIGHT: The headlamp symbol on the transmitter button

will allow you to turn on the headlamps (with optional relay), at any

time to illuminate your path to and from your vehicle. Pressing this

button will turn on the headlamps from the maximum operating dis-

tance of the transmitter. The lights will remain on for 20 seconds then will

automatically turn off.

START: The key symbol on the transmitter button will activate the optional

remote control starting device if added to your vehicle. This button will

always require a double push to active the remote start unit. This is to

prevent accidental, unintended, activation of the remote starting device.

To remote start your vehicle, press this button two times within 5 seconds.

PANIC: This Red circular symbol on the transmitter button will

activate the security system's panic feature. This allows the operator

to turn on the Horn or Siren and flash the parking lights from the maxi-

mum operating range of the transmitter. To activate the Panic feature,

press and hold this button for three seconds. To turn off the panic

mode, press and release the same button one time. If you do not turn

off the panic mode, the Horn or Siren will sound and the lights will

continue to flash for 30 seconds.

NOTE: If there is no separate panic button as shown on your

transmitter, then the red lock symbol button is used for panic. Operation

is the same as described above.

GARAGE: The (optional) Audiovox garage door interface will control

any existing electric garage door from the maximum operating range

of your hand held transmitter. With the interface connected to your

-2-

YOUR ANTI - CODE GRABBING TRANSMITTER:

The four button transmitter included with your security system employs one of the

most secure means of radio frequency transmission available in today's automotive se-

curity systems. Some of the more sophisticated thieves use what is known as a

code grabber. This device is capable of capturing, storing, and then rebroadcasting your

transmitter's code at a later date to disarm your alarm. Your anti-code grabbing

transmitter changes it's code every time you press a button. This changed code is

anticipated by the alarm and your system responds. If a thief captures your

transmitter code in an attempt to rebroadcast it a later date, the alarm, expecting

a different code than what was captured, ignores what the thief transmits. This

makes this system nearly impossible to defeat with a code grabber.

Because of this sophisticated technology, if the transmitter is operated more than

50 times away from the alarm system, it is possible for the unit to go out of

synchronization. If this occurs, simply pressing the arm/disarm transmitter button 2

times within 1 second will realign your transmitter to the alarm. Once realigned,

normal operation is resumed.

PRO-9744: Your Security System has many features and available options, some

of which were selected or added during installation, others can be added at any

time. For your reference, a wallet card provided with your system lists the optional

devices which have been added to your vehicle, as well as show which transmitter

button(s) will be used to activate them. Taking a few minutes to read this manual,

along with the wallet card, will provide you with a better understanding of the

system's operation and it's features.

-3-

existing electric garage door, program this transmitter button

following the program instructions supplied with your AS-9254 kit.

When within range of your garage, press and release this button one

time to open or close your garage door.

LOCK/UNLOCK: The transmitter button with the combined lock and

unlock symbol on it will allow the operator to lock all doors and arm

the alarm system, as well as unlock and disarm the alarm system.

The system can be configured to unlock only the driver's door, or

unlock all doors.

Additionally the system can be configured to unlock the driver's door

then by use of a second button, unlock all remaining doors.

The manner in which the system unlocks the door(s) can be configured at

time of installation to accommodate your personal preference.

OPTION: The transmitter button(s) with the word option, option 1, or

option 2, is available to allow remote control of any optional device

added to your vehicle. Some of the more popular devices are window up,

window down, electric sun roof open or close, fuel door release, etc.... To

operate the optional device, press and release the option button one time.

ARMING THE SYSTEM, Active:

Turn the engine off, exit the vehicle and close all doors, hood, and trunk.

Press and release the transmitter button with the lock icon on it.

The parking lights will flash once, the Horn or Siren will beep or chirp once, and

the dash mounted LED will begin to flash slowly indicating that the system is

armed. If you have the optional door lock/unlock circuit installed, the doors will lock.

NOTE: If the Horn or Siren beeped or chirped three times, this indicates that a

door, hood or trunk has been left ajar. Simply closing that open entry point will

provide full protection. If the Horn or Siren did not beep or chirp upon arming of

the system, then the beeps or chirps have been turned off. Refer to the section

entitled "Eliminating the Arm/Disarm Beeps or Chirps" shown later in this manual.

SILENT ARMING, Active:

Turn the engine off, exit the vehicle and close all doors, hood, and trunk.

Press and hold the transmitter button with the lock icon on it for 2 seconds.

The parking lights will flash once, and the dash mounted LED will begin to flash

slowly indicating that the system is armed. The Horn or Siren will not beep or

chirp. If you have the optional door lock/unlock circuit installed, the doors will

lock.

NOTE: If the Horn or Siren beeped or chirped three times, this indicates that a

door, hood or trunk has been left ajar. Simply closing that open entry point will

provide full protection.

ARMING THE SYSTEM, Passive (Automatic):

If the passive (automatic) arming feature has been selected:

Turn the engine off, exit the vehicle, and close all doors, hood and trunk.

The dash mounted LED will begin to flash rapidly indicating that the 30 second

passive arming cycle has begun. If the LED does not begin to flash rapidly, a

door, hood or trunk has been left ajar. Simply closing that open entry point will

allow the arming cycle to begin. Any entry point opened during the 30 second

arming cycle will suspend the arm timer. When all entry points are closed, the

arm timer will begin again.

At the end of the 30 second arming cycle, the parking lights will flash once, the

Horn or Siren will beep or chirp once, and the dash mounted LED will begin to

flash slowly indicating that the system is fully armed. If the Horn or Siren did not

beep or chirp upon completion of the arming cycle, the beeps or chirps have been

turned off. Refer to the section on "Eliminating the Arm/Disarm Beeps or Chirps"

shown later in this manual. Passive door locking is a selectable feature. If you

have the optional door lock/unlock circuit installed, the doors may or may not lock

dependent on the setting of this selectable feature at time of installation.

PROTECTION WHILE THE SYSTEM IS ARMED:

Opening any of the protected entry points while the system is armed will immediately

cause the alarm system to trigger. The Horn or Siren will sound, and the lights

will flash. If the optional interior illumination circuit has been added, the interior

-4-

light will also flash during the triggered mode. A trigger mode will continue for 30

seconds, the alarm will reset, and continue to monitor your vehicle. If the thief

left a door opened, the triggered mode will continue for six 30 second cycles,

after which, the open door (zone) will be isolated and the system will continue to

monitor all other zones. Whenever the system is armed any strong impact to the

vehicle will cause the shock detector to trigger the alarm system.

Whenever the system is armed, the dash mounted LED will slowly flash. This

serves as a visual deterrent to a potential thief. This LED is a very low current

light emitting diode which will not cause the vehicle's battery to drain even if the

vehicle is left unattended for long periods of time.

Whenever the system is armed, the vehicle starting system is disabled, the ve-

hicle cannot be started even with the ignition key.

DISARMING THE SYSTEM:

As you approach the vehicle, press and release the transmitter button with the

open lock symbol on it. The parking lights will flash two times, the Horn or Siren

will beep or chirp twice, and the dash mounted LED will turn off.

If you have the optional door lock/unlock circuit installed, the doors will unlock. If

you have the optional entry illumination circuit installed, the interior light will turn

on for 20 seconds or until the ignition switch is turned on.

NOTE: If the passive arming mode was selected at time of installation, the LED

will begin to flash rapidly indicating that the system is re-arming. Opening any

door will suspend the automatic arming cycle.

If, when you disarmed the system, the parking lights flashed three times, and the

Horn or Siren beeped or chirped four times, this indicates that the alarm system had

been triggered in your absence. Before turning on the ignition switch, examine the

dash mounted LED's flash pattern. The number of flashes will identify the violated

zone. For additional information, refer to the "Intrusion Warning Signals" shown

later in this manual. If upon disarm, the Horn or Siren did not beep or chirp two

times, refer to the section entitled "Eliminating The Arm/Disarm Beeps or Chirps".

SILENT DISARMING:

As you approach the vehicle, press and hold the transmitter button with the

open lock symbol on it for two seconds. The parking lights will flash two times,

and the dash mounted LED will turn off. If you have the optional door lock/unlock

circuit installed, the doors will unlock. If you have the optional entry illumination

circuit installed, the interior light will turn on for 20 seconds or until the ignition

switch is turned on.

NOTE: If the passive arming mode was selected at time of installation, the LED

will begin to flash rapidly indicating that the system is re-arming. Opening any

door will suspend the automatic arming cycle. If the parking lights flashed three

times, and the Horn or Siren beeped or chirped four times, this indicates that the

alarm system had been triggered in your absence. Before turning on the ignition

switch, examine the dash mounted LED's flash pattern. The number of flashes

identifies the violated zone. For additional information, refer to the "Intrusion

-5-

Warning Signals" shown later in this manual. If upon disarm, the Horn or Siren

did not beep or chirp two times, refer to the section entitled "Eliminating The

Arm/Disarm Beeps or Chirps".

INTRUSION WARNING SIGNALS:

The system will warn you if an intrusion attempt has been made in your absence.

Upon disarm, the Horn or Siren will beep or chirp four times and the parking lights

will flash three times, indicating that the security system had been triggered. Enter

the vehicle and before turning on the ignition switch, observe the LED flash pattern.

If the LED is flashing 1x pause, 1x pause, etc... then an intrusion attempt was

made and detected by the shock sensor.

If the LED is flashing 2x pause, 2x pause, etc... then an intrusion attempt was

made and detected by opening of the hood or trunk.

If the LED is flashing 3x pause, 3x pause, etc... then an intrusion attempt was

made and detected by opening of the vehicle doors.

If the LED is flashing 4x pause, 4x pause, etc... then an intrusion attempt was

made and detected by any additional sensors connected to the vehicle.

All of the above LED patterns are intended to give you the opportunity to inspect

area's of your vehicle for possible damage. These LED warning patterns are

stored in the system's memory and will be erased when the ignition key is turned

to the on position.

VALET OPERATION:

The valet switch allows you to temporarily bypass all alarm functions, eliminating

the need to hand your keychain transmitter to valets or garage mechanics. When

the system is in the valet mode, all alarm features are bypassed. However, the

panic feature, as well as the optional door lock/unlock circuit, will remain operational.

To enter the valet mode:

Start with the alarm disarmed and valet switch in the off position.

Turn the ignition switch to the on position.

Turn the valet switch to the on position.

The dash mounted LED will turn on solid indicating that the valet mode has been

successfully entered.

To return to the normal mode of operation, move the valet switch to the off posi-

tion any time the ignition switch is in the on position.

MANUAL OVERRIDE OPERATION:

In the event that you lose your transmitter or if the transmitter battery fails while

the system is in the armed mode, it will be necessary to override the system to

operate the vehicle. In this situation, to override and disarm the system:

Start with the valet/override switch in the off position. Open the vehicle door with

the door key. (The alarm will sound). Turn the ignition switch to the on position.

"Within 10 seconds" turn the valet/override switch to the on position.

The alarm will disarm and the vehicle can now be started and operated normally.

Always remember to move the valet/override switch to the off position to insure

the vehicle remains protected.

-6-

-7-

ELIMINATING THE NORMAL ARM/DISARM BEEPS OR CHIRPS:

You can selectively eliminate the normal arm and disarm beeps or chirps by holding

the lock or unlock button slightly longer when arming and disarming. This will

prevent the Horn or Siren beeps or chirps for one arm or disarm cycle. If you wish

to disable these beeps or chirps all the time:

Start with the valet/override switch in the off position. Turn the ignition switch on,

then off. Within 10 seconds of turning off the ignition, flip the valet switch on, off,

on, off, on, then off. If the beeps or chirps were enabled before you started, the

Horn or Siren will emit two short beeps or chirps indicating that the beeps or chirps

are now disabled. If the beeps or chirps were disabled before you started, the

Horn or Siren will emit one short beep or chirp indicating that the beeps or chirps

are now enabled.

NOTE: If the beeps or chirps have been disabled, this effects only the normal one

beep or chirp (arm/lock) and the two beep or chirp (disarm/unlock) beeps or chirps.

The three beep or chirp defective zone and the four beep or chirp tamper indication

remain operational. These beeps or chirps are for safety and will not be disabled.

If the vehicle battery is disconnected for servicing, when power is restored, the

arm/disarm beeps or chirps will revert to normal operation.

REMOTE PANIC OPERATION:

The panic feature can be operated from the maximum operating range of your

keychain transmitter. Access to the panic feature can be programmed to operate

from the transmitter button with the red lock symbol on it or can be operated from

a dedicated panic button as shown on page one of this manual. In either case,

dedicated panic button or operation from the lock button, press and hold this

button for 3 seconds to activate the panic feature. Once activated, the Horn or

Siren will sound and the parking lights will flash for a period of 30 seconds. If you

wish to cancel the panic mode anytime during the 30 second cycle, press and

release the button used to activate the feature.

REMOTE SHOCK SENSOR CONTROL:

The shock sensor feature of your security system is intended to detect strong

vibrations or impact to the vehicle when attempted break-ins are made to the

vehicle's glass. The shock sensor is operational every time you lock/arm

your security system. It may be necessary at times to disable the

pre-detect stage of the optional Dual Stage Shock Sensor for one

arming cycle because of harsh thunder storms or when parking along routes of

heavy construction.

If your system was installed with this optional Dual Stage Shock Sensor, to disable

the pre-detect stage for one arming cycle anytime after the system is armed, si-

multaneously press the two transmitter buttons shown.

The Horn or Siren will emit a single chirp indicating that the pre-detect stage of the

Shock Sensor is bypassed for that arming cycle.

STANDARD TRANSMITTER OPTIONS:

REMOTE TRUNK RELEASE BUTTON:

The remote trunk release option, if installed in your vehicle can be

programmed to operate either with a single push of the transmitter

button for 2 seconds, or a double push of the transmitter button. The

programming of your system is indicated on the card packaged with your transmitter.

OPTION BUTTON:

The option button of your transmitter can be programmed to operate a

variety of available options. Some of the more popular devices are

Remote Start, Window Roll Up or Down, Sunroof Open/Close, Garage

door interface.

The operation of your optional device may require a single press or a double

press of the transmitter button with the word "Option" on it. The optional device

connected to your system, and the operation of it is indicated on the card packaged

with your transmitter.

Form No. 128-5352

-8-

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT

TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the user's

authority to operate the equipment.

SYSTEM FUNCTIONS AT A GLANCE

Dash Mounted LED Indications:

Rapid Flashing = Passive Arming

Slow Flashing = Armed

Off = Disarmed

On Solid = Valet Mode

1 Flash Pause... = Intrusion Zone 1

2 Flash Pause... = Intrusion Zone 2

3 Flash Pause... = Intrusion Zone 3

4 Flash Pause... = Intrusion Zone 4

Siren and or Horn/Light Indications:

1 Chirp, 1 Flash = Armed

2 Chirps, 2 Flashes = Disarmed

3 Chirps, 2 Flashes = Arming With Door Ajar

4 Chirps, 3 Flashes = Disarming After Intrusion

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox PRO 9549FT3 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO9644i Bedienungsanleitung

Audiovox

Audiovox UltraGuard PRO 9549UG Bedienungsanleitung

Audiovox

Audiovox AA-9347 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 2000S Bedienungsanleitung

Audiovox

Audiovox Prestige 128-8146 Bedienungsanleitung

Audiovox

Audiovox APS996A - Prestige Remote Security System Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-250-A Bedienungsanleitung

Audiovox

Audiovox Prestige APS99BT3 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9344FT Bedienungsanleitung

Audiovox

Audiovox AS9233ST Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-596N Bedienungsanleitung

Audiovox

Audiovox Platinum APS 500 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-510 Bedienungsanleitung

Audiovox

Audiovox AA-RS20CS Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9649b Bedienungsanleitung

Audiovox

Audiovox Auto Security SS92 Betriebsanleitung

Audiovox

Audiovox Prestige Platinum APS-350-A Bedienungsanleitung

Audiovox

Audiovox APS-95BT2 Betriebsanleitung

Audiovox

Audiovox Prestige Platinum APS-410a Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS 995 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9642 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-510a Bedienungsanleitung

Audiovox

Audiovox Professional PS-330i Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung