Audiovox Pursuit PRO 2000S Bedienungsanleitung

Model PRO 2000S

Owner’sManual

3 Button Remote Security System with

Keyless Entry

IMPORTANT !

In order to provide the highest possible level of security to your vehicle, this

system is equipped with selectable manual override circuitry. It is possible that you will need

to manually override your security system if the transmitter becomes lost, or inoperative due

to battery failure. Reading the sections on " MANUALLY OVERRIDING YOUR SYSTEM " is

necessary to fully understand the procedure required to enable your vehicle in such situa-

tions. In addition, the chart on the last page of this manual has a section for the particular

features and options installed in your vehicle as well as the override method selected.

Valet

Switch manual override is pre-selected from the factory,

however, the system can be

configured for "Custom Code" operation. Confirm the override mode selected on the last

page of this manual, and familiarize yourself with the selection on it's operation.

FEATURES :

w2ThreeButtonProgrammableRFTransmitters

(capableofaccepting4transmitters)

wFour Channel Receiver

wSelectable Manual Override Mode

wRemote Panic in all modes

wProtected Valet

wUser Programmable Manual Override Code

w7 Function LED - Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming

wIntrusion Alert with Memory

wAudible Arm / Disarm / Defective Zone / Tamper Confirmation

wInstant Siren Activation

wTrue Last Door Arming ( hardwire only )

wDefective Zone By-Pass

wHardwire or Voltage Sense Selectable

wActive or Passive Arming Selectable

wProgrammable Auto Lock On / Off

wProgrammable Auto Unlock On / Off

wProgrammable Door Lock Pulse Duration

wProgrammable Active or Passive Door Locks

wUserProgrammable PermanentChirp Delete

wOn Command RF Chirp Delete from Transmitter Or Selectable Through Software

wAdditional Negative Trigger Input

w6 Tone Multi Tone Siren (And or)

wCar Horn Activation for additional alarm response

wRF Inhibit with ignition on

wParking Light Flasher

wRemote Trunk Release ( Option and must have electronic trunk release )

wRemote Keyless Entry With Optional Access Guard ( must have power door locks )

OPTIONS :

wIlluminatedEntry

wStarter Disable

wMultiple Vehicle Capable

wRemote Starter

wRemote Power Window Roll Up

wRemote Garage Door Interface

wPlug In Electronic Shock Sensor

THISPAGE INTENTIONALLYLEFT BLANK

NOTE: This unit uses the vehicles horn as a sounding device. In some installa-

tions the optional siren may have been used in place or or in addition to

the vehicle horn as a sounding device. Where siren chirps are referenced

below, the horn beeps may be substituted or in addition to.

ARMINGTHESYSTEM-ACTIVE

1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.

2. Press and release the Lock button on the keychain transmitter.

þRed dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren sounds one chirp.

If the siren sounds 3 chirps, then you have left a door, trunk, or

hood lid ajar. Simply close the opened entry point to provide full

protection. If the siren did not sound when arming, then the

chirps have been turned off, and you should refer to the section

titled“ELIMINATINGTHEARM/DISARMCHIRPS”inthismanual.

þDoors Lock

SILENTARMING-ACTIVE

1. Turn off the engine, exit the vehicle and close all doors, hood lid, and trunk lid.

2. Press and hold the Lock button on the keychain transmitter for 2 seconds.

þRed dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren will not sound.

If the siren sounds 3 chirps, then you have left a door, trunk, or

hood lid ajar. Simply close the opened entry point to provide full

protection.

þDoors Lock

ARMINGTHESYSTEM - PASSIVE( AUTOMATIC )

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid and

trunk lid.

þRed dash mounted LED begins to flash rapidly, indicating 30 second

passive arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle

will immediately suspend automatic arming and the 30 second passive arming

cycle will re-start when all doors are closed. At the end of the passive arming

cycle; þRed dash mounted LED begins to flash slowly.

þParking Lights flash one time.

þSiren sounds one chirp

If the siren did not sound when arming, then the chirps have

been turned off, and you should refer to the section titled

“ELIMINATING THE ARM / DISARM CHIRPS” in this manual.

þDoors Lock

Door locking during passive arming is a selectable feature.

The alarm can be programmed to allow the doors to lock only

when arming using the keychain transmitter, and they will not

automatically lock during passive arming.

PROTECTIONWHILE THESYSTEMISARMED

þOpening any protected door, hood, or trunk lid will cause the alarm to

immediately sound. The alarm will continue to sound for 30 seconds, then

stop and continue to monitor all protected entry points. If the thief left a door

opened, the alarm will sound for six 30 second cycles, remain armed, and

ignore that triggered zone.

þWhenever the system is armed, the red dash mounted LED indicator

will slowly flash. This serves as a visual deterrent to the potential thief. The

LED is a very low current bulb, and will not cause the vehicle’s battery to

drain, even when left unattended for extended periods.

þWhenever the system is triggered, the vehicle’s parking lights will flash

for the full 30 second alarm cycle, attracting visual attention to the vehicle.

oOPTIONAL Whenever the system is triggered, the interior courtesy lights

will flash for the full 30 second alarm cycle.

oOPTIONAL Whenever the system is armed, the vehicle’s starting circuit

will be bypassed. If the thief should choose to ignore the siren, the vehicle

can not be started.

oOPTIONAL Any strong impact to the vehicle’s glass will cause the alarm

to trigger for the full 30 second alarm cycle.

DISARMINGTHESYSTEM

1. As you approach the vehicle, press and release the Unlock button on the

keychain transmitter.

þRed dash mounted LED turns off.

If passive arming was selected during the installation, then the LED will

start flashing rapidly, indicating that the system is re arming automati-

cally. Open any door to suspend the automatic arming.

þParking Lights flash two times.

If the parking lights flashed three times, then the alarm was triggered in

your absence. Before turning the key on, examine the LED to identify

which zone was triggered.

þSiren sounds two chirps.

If the siren sounds 4 chirps, then the alarm was triggered in

your absence. Before turning the key on, examine the LED

and refer to the INTRUSION WARNING SIGNALS section of

this manual to identify which zone was triggered.

If the siren did not sound when disarming, then the chirps

have been turned off, and you should refer to the section titled

“ELIMINATING THE ARM / DISARM CHIRPS” in this manual.

þDoors Unlock.

Using the optional Access Guard feature, the alarm can be

wired to unlock only the drivers door during this step. To unlock

all the doors, press and release the Unlock button of the

transmiter a second time within 3 seconds.

(Power Door Locks Required.)

oOPTIONAL Courtesy lights turn on for 30 seconds, or until the

ignition key is switched on.

SILENTDISARMING

1. As you approach the vehicle, press and hold the Unlock button on the keychain

transmitter for 2 seconds.

þRed dash mounted LED turns off.

If passive arming was selected during the installation, then the

LED will start flashing rapidly, indicating that the system is re

arming automatically. Open any door to suspend the automatic

arming.

þParking Lights flash two times.

If the parking lights flashed three times, then the alarm was

triggered in your absence. Before turning the key on, examine

the LED to identify which zone was triggered.

þSiren will not sound.

If the siren sounds 4 chirps, then the alarm was triggered in

your absence. Before turning the key on, examine the LED

and refer to the “INTRUSION WARNING SIGNALS” section of

this manual to identify which zone was triggered.

þDoors Unlock.

Using the optional Access Guard feature, the alarm can be

wired to unlock only the drivers door during this step. To unlock

all the doors, press and release the Arm/Disarm button of the

transmiter a second time within 3 seconds. (Power Door Locks

Required.)

oCourtesy lights turn on for 30 seconds, or until the ignition key is

switched on.

WHILETHE SYSTEMISSOUNDING

If during a triggered state, you wish to shut off the siren without disarming your

security system, simply press and release any transmitter button other than the

disarm button. This action will turn off the siren yet leave the vehicle fully armed

and protected. This feature is partictularily useful if you are aware of children

playing near your vehicle that may accidently trigger your security system. In this

case you can cancel the siren sounding without disarming your system.

INTRUSIONWARNINGSIGNALS

This system will inform you if an intrusion attempt has occurred while you were

away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4

times and the parking lights will flash 3 times when disarming the system. Enter

the vehicle and observe the red dash mounted LED to identify which zone was

triggered.

1) If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to the one of the pin switches typically

installed under the hood or in the trunk, or an optional sensor connected

to the unit.

2) If the LED is flashing two times...pause...two times...pause...etc., then

an intrusion attempt was made to a hood or trunk pin switch that was

added to the system, or to a light activated entry point if the alarm was

installed using the voltage sensing feature.

3) If the LED is flashing three times...pause...three times...pause...etc.,

then an intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will

only be erased when the ignition key is turned on.

VALETSWITCH

The valet switch allows you to temporarily bypass all alarm functions, eliminating

the need to hand your transmitter to parking attendants or garage mechanics.

When the system is in valet mode, all alarm functions are bypassed, however the

remote panic feature and remote door locks will remain operational. To use the

valet mode, the system must first be disarmed either by using your keychain

transmitter, or by activating your personalized manual override code.

1. Enter the vehicle and turn the ignition key to the on position.

2. Press and hold the valet pushbutton switch until the dash mounted

LED turns on solid. The system will remain in the valet mode.

3. To return to normal operation, press and release the pushbutton

switch any time the ignition is on.

NOTE: Always remember to exit the valet mode. This will ensure that the vehicle

remains protected at all times.

MANUALLYOVERRIDING YOURSYSTEM:

USINGTHEVALETSWITCHMANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmit-

ter. This is necessary, since you will need the ability to operate your vehicle if the

transmitter is lost or its battery fails. If your system has been selected for Valet

Switch manual override as indicated on the last page of this manual, to by-pass

the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the valet pushbutton switch.

The alarm system will stop sounding. You can now start and operate the vehicle

normally.

Typically this override mode is used only if the transmitter has become inoperative.

If this is the case, you may want to enter the valet mode until a operating or

replacement transmitter is available.

PROGRAMMINGTHECUSTOMCODEMANUALOVERRIDE

Unlike override switches easily found, and defeated, this security system allows

the consumer to program a personal override code, offering a higher level of

security. To take advantage of this option, programmable feature # 9 must be

selected for the Custom Code Option. Consult your installation center for pro-

gramming details. The system comes from the factory with a pre-programmed

override code of 11. To change this default override code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the valet/override switch, 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and

releasing the pushbutton switch from 1 up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off

then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and

releasing the pushbutton switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by

flashing the LED, first indicating the 10ths digit, pause and then the units digit.

The unit will report the new code three times with a one second pause between

each code, then the system will begin arming. If the LED flash pattern reports

the previously stored code, the new code was not entered correctly. Please

repeat steps 1 through 7 above considering the following.

NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recog-

nize a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert

back to the last successfully stored code.

Custom Code Programming Example:

To Change the code from the factory pre-assigned code of 11 to “52” you would

do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency

override sequence.

2. Turn the ignition switch to the on position.

3. Within 10 seconds, press and release the valet/override switch, 3 times.

4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.

(The siren or horn will beep and the lights will flash one time.)

5. Within 10 seconds, begin to press and release the push button switch to set

the tenths digit.

(As per the example, press and release 5 times to set the tenths digit to 5)

6. Within 10 seconds of the last press of the push-button, turn the igntion switch

off then on.

7. Within 10 seconds, begin to press and release the push button switch to set

the units digit.

(As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position. Immediately observe the LED flash

pattern.

You will note the LED flashing five times, pause and then flash two times, pause.

This pattern will be repeated three times indicating the new code (52) has been

accepted and stored in memory.

NOTE: If after step 7, the LED flashes a code other than what was just entered,

this indicates that the code has not been changed. You will have to repeat

steps 1 through 7 above being certain to note the following:

Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0

(Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert

back to the last successfully stored code.

MANUALLYOVERRIDING YOURSYSTEM:

USINGTHECUSTOMCODEOVERRIDE

Assuming the override code programmed has not been changed and the default

override code of 11 is in the system's memory.

1) Enter the vehicle and turn the ignition switch to the on position.

Note: The siren will sound.

2) Within 5 seconds, press and release the pushbutton switch 1 time.

3) Within 5 seconds, turn the ignition switch off then on.

4) Within 5 seconds, press and release the pushbutton switch 1 time.

5) Turn the ignition switch off then on and start the vehicle.

Note: If you have changed the programmed override code then substitute your

new code tenths for step 2 above, and units for step 5 above.

ELIMINATING THENORMALARM/ DISARMCHIRPS

As explained earlier in the manual, you can eliminate the chirps selectively any

time you arm or disarm the system simply by holding the ARM / DISARM button for

two seconds. If you find the normal arming and disarming chirps annoying, they

can be turned off permanently, eliminating the need to hold the ARM / DISARM

button for two seconds. To do this,

1. Turn the ignition key on then off.

2. Within 10 seconds, press and release push-button switch three times.

3. If the chirps were on before you started, then you will hear 2 chirps indicating

they have been turned off.

If the chirps were off before you started, then you will hear one chirp indicating

they have been turned on.

NOTE: Whenever the chirps are by-passed, the 4 chirp intrusion indicator and 3

chirp defective zone indicator will always operate. Since these are important

warnings to you that something has happened, they cannot be eliminated.

REMOTEPANICOPERATION

The Lock or Unlock button on your keychain transmitter also functions as a panic

switch for use in emergency situations. To use remote panic,

1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or

more seconds. The alarm will immediately sound.

2. To stop the alarm, press and hold the Lock or Unlcok button on the transmitter

again for 3 seconds. If the button is not pressed, the alarm will automatically

stop after 30 seconds. Also if any transmitter button other than the Lock or

Unlock button is pressed and released, the Panic mode will be turned off

immediately. The normal function of this transmitter button will be suspended

during the Panic sounding period.

NOTE: While in the Panic mode, pressing and releasing the Lock, or the Unlock

buttons will, if the option is installed, lock and unlock the doors respec-

tively. While in the panic mode, anytime the unlock button is pressed, the

the panic feature will continue for the alloted 30 seconds, however, the

security system will be disarmed allowing the vehicle to start.

OPTIONALDEVICE OUTPUT ( CHANNEL3)

ControlledBy:

oOption Button

oBoth Lock & Unlock Button

oBoth Option & Lock Button, or

oBoth Option and Unlock Button.

This security system is equipped with an output which will activate when the

appropriate transmitter button is depressed for 4 seconds. Optional devices that

may be connected to this channel are;

oRemote Electric Trunk Release

oRemote Car Starter

oRemote Window Closure

oRemote Garage Door Interface

NOTE: In addition there may be a second optional feature connected to your

system that when the same transmitter button is pressed and released 2

times within 3 seconds (double pressed), the second optional feature will

activate. This output is typically used for a remote start option and will

likely prevent inadvertent activation of the remote start device if young

children are playing with the hand held transmitter.

If your vehicle is not equipped with an electronic trunk release switch, or other

option listed, this feature may have been connected to another accessory. Please

ask your dealer for further information.

ADDITIONALREMOTEFUNCTION( CHANNEL4)

ControlledBy:

oOption Button

oBoth Lock & Unlock Button

oBoth Option & Lock Button, or

oBoth Option and Unlock Button.

This security system has an additional feature that can be connected to a number

of different optional accessories. Some of the more common uses for this chan-

nel are; oRemote Car Starter

oRemote Window Closure

oRemote Garage Door Interface

To remotely operate the device indicated, momentarily press, or press and hold

the appropriate transmitter button(s) as indicated above.

Andere Handbücher für Pursuit PRO 2000S

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox Keyless Entry Alarm Upgrade Module APS-30 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-155 Bedienungsanleitung

Audiovox

Audiovox PRO-9344FT Pursuit Series Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9649b Bedienungsanleitung

Audiovox

Audiovox Auto Security SS92 Betriebsanleitung

Audiovox

Audiovox Prestige Platinum 128-8117 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25KB Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-4631B Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS 995 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-15R Bedienungsanleitung

Audiovox

Audiovox XRO9100 Bedienungsanleitung

Audiovox

Audiovox Prestige AS-9256 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-596N Bedienungsanleitung

Audiovox

Audiovox PRO 9549FT3 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-255 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9600 Bedienungsanleitung

Audiovox

Audiovox PRO-9649a Bedienungsanleitung

Audiovox

Audiovox APS-596C Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9642CH Bedienungsanleitung

Audiovox

Audiovox Prestige APS-35-CL Bedienungsanleitung

Audiovox

Audiovox APS-25C Bedienungsanleitung

Audiovox

Audiovox ca 6552 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9675FT Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9842 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung