Audiovox UltraGuard PRO 9549UG Bedienungsanleitung

Model PRO 9549UG

Owner’s Manual

Page 1

Dear Valued Customer,

The installation of the UltraGuard Security System on your vehicle has

been activated to provide you with the ultimate in vehicle protection. The

following features have been noted as standard in the installation of your

Auto Security System. Additional Security and Convenience features have

been noted under options and are available at an additional cost.

Standard Features:

2 Three Button Programmable RF Transmitters Four Channel Receiver

Code Hopping Technology Remote Panic in All Alarm Modes User

Programmable Override Code Intrusion Alert with Memory Audible Arm/

Disarm/Defective Zone Audible Tamper Confirmation Instant Siren Ac-

tivation Start Disable Last Door Arming Defective Zone By-Pass On

command RF Chirp Delete 6 Tone Siren Remote Keyless Entry* RF

Inhibit with Ignition ON Headlight Illumination during Arm/Disarm Pro-

grammable Features (refer to owner's manual) Infrasonic Shock Sensor

Remote Access Guard* Remote Trunk Release**

Optional Features:

7 Function L.E.D. Light Illuminated Entry Additional Engine Immobi-

lizer Parking Light Flash Vehicle Horn Activation Remote Start 

Remote Power Window Roll Up Remote Garage Door Interface Sport

Series Transmitter

* Vehicle must be equipped with Electronic Door Locks.

** Vehicle must be equipped with Electronic Trunk Release.

UltraGuard Security Systems 15600 Roscoe Blvd., Van Nuys, CA 91406 (818) 902-0393

Page 2

3 Button Remote Security System with

Shock Sensor, Starter Disable, & Keyless Entry

IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this

system is equipped with selectable manual override circuitry. It is possible that you will need to

manually override your security system if the transmitter becomes lost, or inoperative due to

battery failure. Reading the sections on " MANUALLY OVERRIDING YOUR SYSTEM " is

necessary to fully understand the procedure required to enable your vehicle in such situations.

In addition, the chart on the last page of this manual has a section for the particular features

and options installed in your vehicle as well as the override method selected. Valet Switch

manual override is pre-selected from the factory, however, the system can be configured

for "Custom Code" operation. Confirm the override mode selected on the last page of this

manual, and familiarize yourself with the selection on it's operation.

FEATURES :

2 Three Button Programmable RF Transmitters

Four Channel Receiver

( capable of accepting 4 transmitters )

Code Hopping Technology

Remote Panic in all modes

Protected Valet

User Programmable Manual Override Code (optional)

Intrusion Alert with Memory

Audible Arm / Disarm / Defective Zone / Tamper Confirmation

Instant Siren Activation

Starter Disable

True Last Door Arming ( hardwire only )

Defective Zone By - Pass

Hardwire or Voltage Sense Selectable

Active or Passive Arming Selectable

Programmable Auto Lock On / Off

Programmable Auto Unlock On / Off

Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds

Programmable Active or Passive Door Locks

User Programmable Permanent Chirp Delete

On Command RF Chirp Delete from Transmitter

6 Tone Multi - Tone Siren

Car Horn Activation for additional alarm response

Additional Negative Trigger Input

RF Inhibit with ignition on

Access Guard

Plug In Electronic Shock Sensor

Headlight Illumination during Arming and Disarming

Remote Keyless Entry with optional Access Guard (must have power door locks)

Illuminated Entry

Remote Trunk Release (must have electronic trunk release)

OPTIONS :

Illuminated Entry

Multiple Vehicle Capable

Parking Light Flasher

Remote Starter

Remote Power Window Roll Up

Remote Garage Door Interface

Page 3

YOUR “ CODE HOPPING “ TRANSMITTERS

The transmitters included with your new security system use the most advanced and secure

form of radio frequency transmission available on any current automotive security system.

Some of today’s sophisticated auto thieves use a device known as a code grabber, which will

receive and store the signal from your keychain transmitter, and re-transmit at a later time to

disarm your system.

Your code hopping transmitters will change their signal every time the button is pressed, so

when a thief grabs then re transmits your signal, the alarm system will not respond.

If your transmitter button is pressed more than fifty times while it is out of range of the vehicle

( children playing with your keys ), the transmitter will not operate when you return to the

vehicle, and will need to be re-aligned to the receiver. To do this, simply press button 1 two

times within a one second time period. The system will now re-

spond to that transmitter each time a button is pressed.

ARMING THE SYSTEM - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood

lid, and trunk lid.

2. Quickly press and release the Lock, Arm/ Unlock, Disarm button

on the keychain transmitter.

Siren sounds one chirp.

If the siren sounds 3 chirps, then you have left a door,

trunk, or hood lid ajar. Simply close the opened entry point to provide full protection.

If the siren did not sound when arming, then the chirps have been turned off,

and you should refer to the section titled “ ELIMINATING THE ARM / DISARM

CHIRPS “ in this manual.

Doors Lock.

Headlight Illumination.

The vehicle’s headlights turn on for approximately 30 seconds, illuminating the

path as you leave the vehicle.

SILENT ARMING - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and hold the Lock, Arm/ Unlock, Disarm button on the keychain transmitter for 2 seconds.

Doors Lock.

Headlight Illumination.

The vehicle’s headlights turn on for approximately 30 seconds, illuminating the

path as you leave the vehicle.

DISARMING THE SYSTEM

1. As you approach the vehicle, quickly press and release the Lock, Arm / Unlock, Disarm

button on the keychain transmitter.

Siren sounds two chirps.

If the siren sounds 4 chirps, then the alarm was triggered in your absence. If the

siren did not sound when disarming, then the chirps have been turned off, and you

should refer to the section titled “ ELIMINATING THE ARM/DISARM CHIRPS “ in

this manual.

Doors Unlock.

Using the optional ACCESS GUARD feature, the alarm can be wired to unlock only

the driver’s door during this step. To unlock all doors, press and release the Lock,

Page 4

Arm / Unlock,Disarm button a second time within 3 seconds.

Headlight Illumination.

The vehicle’s headlights turn on for approximately 30 seconds, illuminating the path

to the vehicle.

SILENT DISARMING

1. As you approach the vehicle, press and hold the Lock, Arm / Unlock,Disarm button on the

keychain transmitter for 2 seconds.

Doors Unlock.

Using the optional ACCESS GUARD feature, the alarm can be wired to unlock only

the driver’s door during this step. To unlock all doors, press and release the Lock,

Arm / Unlcok, Disarm button a second time within 3 seconds.

Headlight Illumination.

The vehicle’s headlights turn on for approximately 30 seconds, illuminating the path

to the vehicle.

VALET SWITCH

The valet switch allows you to temporarily by-pass all alarm functions, eliminating the need to

hand your transmitter to parking attendants or garage mechanics. When the system is in valet

mode, all alarm functions are by-passed; however, the remote panic feature and remote door

locks will remain operational. To use the valet mode, the system must first be disarmed either

by using your keychain transmitter, or by activating your personalized manual override code.

1. Enter the vehicle, and turn the ignition key to the on position.

2. Move the valet toggle switch to the on position.

3. To return to normal operation, move the valet switch back to the off position any

time the ignition is on.

NOTE : Always remember to move the valet switch back to the off position. This will ensure that

the vehicle remains protected at all times.

USING THE VALET SWITCH MANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter. This is

necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its

battery fails. If your system has been selected for Valet Switch manual override as indicated on

the last page of this manual, to by-pass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Start with the Valet Switch in the off position.

3. Turn the ignition key to the on position.

4. Within 5 seconds, turn the valet switch to the on position.

The alarm system will stop sounding and enter the valet, (by-passed) mode. This is indicated

by the dash mounted LED turning on. You can now start and operate the vehicle normally. To

return to normal operation, move the valet switch back to the off position any time the ignition is

on.

OPTIONAL:

This programmable manual override is an optional feature that can be activated by your car

dealer.

PROGRAMMING THE CUSTOM CODE MANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter. This is

necessary, since you will need the ability to disarm the system if you lose your transmitter, or if

the transmitter battery fails.

Page 5

If your system has been selected for Custom Code manual override as indicated on the last

page of this manual, in order to provide the highest level of security, this system will allow you

to program your personal manual override code. This code isa(2)digit code. The first digit

must be a digit from 1 through 9, and the second digit must be either 1, 2, or 3.

To program your access code, the security system must be in the disarmed state. Once dis-

armed, program your code as follows;

1. Turn the ignition key on, then off, then on.

2. Within 3 seconds of step 1, flip the Valet switch on, then off. The siren will sound

one short chirp, followed by one long chirp. This indicates that the system is in the

manual override programming mode.

3. The red dash L.E.D. will begin to count by flashing. Allow the L.E.D. to flash until

it gets to the first digit of your selected code.

4. As soon as the L.E.D. turns on for the corresponding number of your first digit,

quickly turn the ignition key;

1. off then on for second digit 1

2. off then on twice for second digit 2

3. off then on three times for second digit 3.

5. The siren will sound one short chirp, followed by one long chirp, indicating that the

code has been memorized.

6. After a 2 second pause, the L.E.D. will flash confirmation of the stored code,

beginning with the first digit, then a pause, then the second digit.

EXAMPLE : To program the manual override code 52, you would;

1. Turn the ignition key on, then off, then on.

2. Within 3 seconds of step 1, flip the Valet switch on, then off. The siren will sound

one short chirp, followed by one long chirp. This indicates that the system is in the

manual override programming mode.

3. Allow the L.E.D. to flash 5times, and during or immediately after the fifth flash,

quickly turn the ignition key to off, then on, then off, then on.

4. The siren will sound one short chirp, followed by one long chirp, indicating that the

code has been memorized.

5. After a 2 second pause, the L.E.D. will flash 5times, then pause, then flash 2

times. This confirms that the code 52 has been stored into memory.

USING THE CUSTOM CODE MANUAL OVERRIDE

It is very important that you understand how to operate the manual override feature, as there

may a time that you will need to bypass the alarm when your transmitter is not working. You

should also write down your personalized code number, and keep it in a safe place for future

reference.

To by pass the alarm,

1. Open the door. The alarm will sound.

2. Turn the ignition key to the on position. The alarm will stop for three seconds, then

the siren will begin counting with long chirps.

3. As soon as the chirp that corresponds with your first digit sounds, quickly turn the

ignition key ;

1. off then on if your second digit is 1

2. off then on twice if your second digit is 2

3. off then on three times if your second digit is 3.

4. The alarm will stop sounding, and you can now start the vehicle.

EXAMPLE : To override the system using the example 52 above, you would,

1. Open the door. The alarm will sound.

REMOTE PANIC OPERATION

The Lock,Arm / Unlock, Disarm button on your keychain transmitter also functions as a panic

switch for use in emergency situations. To use remote panic,

1. Press and hold the Lock,Arm / Unlock, Disarm button on the keychain transmitter

for 3 or more seconds. The alarm will immediately sound.

2. To stop the alarm, press and hold the Lock,Arm / Unlock, Disarm button on the

transmitter again for 3 seconds. If the button is not pressed, the alarm will auto-

matically stop after 30 seconds.

NOTE : All normal transmitter functions will operate in the panic mode.

REMOTE TRUNK RELEASE ( CHANNEL 2 )

This security system is equipped with an on-board trunk release relay which will activate the

existing factory installed electronic trunk release switch. If your vehicle is not equipped with an

electronic trunk release switch, this feature may have been connected to another accessory.

Please ask your dealer for further information.

To remotely open the trunk, press and hold the Trunk button on the keychain transmitter for four

seconds.

ADDITIONAL REMOTE FUNCTION ( CHANNEL 3 ) OPTION

This security system has an additional feature that can be connected to a number of different

optional accessories. Some of the more common uses for this channel are;

Remote Car Starter

Remote Window Closure

Remote Garage Door Interface

To activate the optional accessory, press the option button on the keychain transmitter. The

optional accessory will immediately engage.

ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 ) OPTIONS

This security system has an additional feature that can be connected to a number of different

optional accessories. Some of the more common uses for this channel are;

Remote Car Starter

Remote Window Closure

Remote Garage Door Interface

To activate the optional accessory, press both the trunk and option buttons on the keychain

transmitter simultaneously. The optional accessory will immediately engage.

PRO 9549UG

SYSTEM FUNCTIONS AT A GLANCE

SIREN AND / OR HORN CHIRP INDICATORS

1 CHIRP * = ARM

2 CHIRPS * = DISARM

3 CHIRPS = ARM / DOOR OPENED

4 CHIRPS = DISARM / INTRUSION

* These chirps are optional, and can be de - activated.

Your System Has These Features Activated

Auto Lock with ignition key

Auto Unlock with ignition key

Headlight Illumination during arm & disarm

Passive Arming

No Lock in passive mode

Hardwire doors, hood, and trunk

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox Prestige Platinum APS-255CH Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-510 Bedienungsanleitung

Audiovox

Audiovox PurSuit PRO-9642CHWOS Bedienungsanleitung

Audiovox

Audiovox Professional PS-330i Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-995C Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 2000S Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 2000S Anleitung zur Verwendung

Audiovox

Audiovox Prestige Platinum APS-510a Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-400 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-8533 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9775T Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-8124 Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25KB Bedienungsanleitung

Audiovox

Audiovox APS-95BT2 Betriebsanleitung

Audiovox

Audiovox Prestige Platinum APS-250-A Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-410a Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25-CL Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-700 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum 128-4627A Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-786T Bedienungsanleitung

Audiovox

Audiovox AA-9124 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-596a Bedienungsanleitung

Audiovox

Audiovox Exclusive EX-6000 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO9644i Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung