Audiovox APS-95BT2 Betriebsanleitung

Factory Settings for Transmitter Buttons

Button Channel System Function

Button # 1

Button # 2

Both Buttons

Remote Arm/Disarm

Remote Emergency Panic

Door Lock/Unlock (Optional)

Pulsed Output

*(Optional Devices)

Switched Output

* (Optional Devices)

* Some of the more common accessories for these channels are;

AS 9075 Remote Car Starter

AS 9256 Remote Trunk Release Relay

AS 9154 Remote Garage Door Interface

AS 9153 Remote Window Roll Up

Model : APS 95 BT2

TRANSMITTER PROGRAMMING GUIDE

The transmitters included in the security system kit are pre-programmed at

the factory, with button # 1 assigned to channel one only. The suggested

program arrangement is listed below. To program channels 2 and 3, please

follow the programming instructions listed on pages two and three of this

manual.

Thesefactoryprogrammedsettingscanbeprioritizedbasedonanindividual's

frequency of use, (i.e. pressing both buttons simultaneously to activate

channel1,arm/disarmetc.)byfollowingthenormalprogramminginstructions

below.

Please note when changing the factory set button assignments, it is

necessary to perform steps 5, 9, and 12 three times using "transmitter A",

followed by one time using "transmitter B".

PROGRAMMING TRANSMITTERS:

It is important to remember that during programming, each individual step

of the procedure must be executed within 15 seconds of the previous step.

When the 15 second time limit is allowed to expire, the system will

automaticallyexitprogrammode. Thisis indicatedbyalong"chirp"fromthe

siren.

Additionally, any time the ignition key is turned off while programming, the

system will immediately exit program mode. This is also indicated by a long

"chirp" from the siren.

TO PROGRAM ADDITIONAL TRANSMITTERS:

1. Enter the vehicle, and turn the ignition key to the "on" position.

2. Move the valet/bypass switch on - off - on - off - on then off.

3. The dash LED will flash once, and the siren will "chirp" once, indicating

the system is ready to accept programming for channel 1 or the arm/

disarm and panic functions.

4. You can assign any of the three transmitter button functions listed below

to channel 1.

a. Pressing button #1 on the keychain transmitter.

b. Pressing button #2 on the keychain transmitter.

c. Pressing both buttons simultaneouslyon the keychaintransmitter.

5. Press and hold the selected choice a, b, or c above, until the siren emits

a long "chirp" to confirm that programming of channel 1 was successful.

6. Move the valet/bypass switch on, then off again.

7. The dash mounted LED will flash 2 times, and the siren will "chirp"

indicating that the system is ready to accept programming for channel

2, or the pulsed ground output for remote trunk release, remote car

starter, etc.

8. You can assign any one of the two remaining button functions listed in

4a, 4b, or 4c above to operate channel 2. You cannot use the button(s)

that operate channel 1, selected in step 5, to operate channel 2.

9. Press and hold the selected choice. The siren will emit a long "chirp" to

confirm that programming of channel 2 was successful.

10. Move the valet/bypass switch on, then off again.

11. The dash mounted LED will flash 3 times, and the siren will "chirp"

indicating that the system is ready to accept programming for channel

3. (APS 350)

12. Press and hold the remaining transmitter button function. The siren will

emit a long "chirp" to confirm that programming of channel 3 was

successful.

13. To exit program mode, either turn the ignition key to the off position, or

move the valet switch on then off one additional time. This is indicated

by one short chirp then one long "chirp" from the siren.

NOTE: If programming to a Keyless Entry (non alarm) unit, there will be NO

chirp indication.QUICK REFERENCE:

You can program any individual channel, without reprogramming all

channels, by following the quick reference chart below.

After the desired channel is programmed, turn the ignition key to the off

position to exit programming mode.

BATTERY REPLACEMENT:

The transmitter incorporates a small red LED built into the case. This LED

can be used to indicate battery condition. You will notice a decrease in

transmitter range as the battery condition deteriorates. To replace the

battery...

1. Removethetransmittercoverbyremovingthesmallscrewfromtheback

of the transmitter case.

2. Remove the discharged battery, making note of the orientation of the +

and - contacts and dispose of the battery properly.

3. Install the new (type GP23A) battery, taking care to orient the + and -

contacts properly.

4. Replace the transmitter cover, taking care not to damage the LED or

switches on the circuit board. 3

CHANNEL VALET SWITCH

ON then OFF 3 Times

ON then OFF 4 Times

ON then OFF 5 Times

LED

1 Flash

2 Flashes

3 Flashes

IMPORTANT: To help us expedite your order, please print all of the

information legibly, and mail this form and your payment according to the

instructions below.

1.Name :______________________________________________________

Address:_____________________________________________________

City:___________________ State:________ ZipCode:______________

2. TelephoneNumber:(________ )________________________________

3. Enterthetotalnumberoftransmittersrequiredhere:____________________

4. The cost per transmitter is $ 65.00.

5. Enterthetotalamountenclosedhere:_______________________________

( New York state residents must include the appropriate sales tax. )

6. Method of payment; check one of the boxes below.

qMastercard qVisa qCheck or money order * (do not send cash)

* Make checks payable to Audiovox Corporation

7. CreditCardNumber:___________________________________________

8. Credit Card Expiration Date : __________________________

9. Mail this form and your check, to :

ORDER FORM FOR 2 BUTTON TRANSMITTER

MODEL NO. APS 95 BT2

Audiovox Corporation

150 Marcus Blvd.

Hauppauge, N.Y. 11788

Attn: TRANSMITTER DEPARTMENT

Credit card purchasers can order additional or replacement

transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and

follow the instructions from the operator interface.

(

128-4624C

Inhaltsverzeichnis

Andere Audiovox Autoalarmanlage Handbücher

Audiovox

Audiovox Prestige 128-8146 Bedienungsanleitung

Audiovox

Audiovox PS-155CH Bedienungsanleitung

Audiovox

Audiovox Prestige APS-15KB Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25HJ Bedienungsanleitung

Audiovox

Audiovox 5BCR07 Betriebsanleitung

Audiovox

Audiovox Auto Security AA-931 Bedienungsanleitung

Audiovox

Audiovox Prestige AS-9256 Bedienungsanleitung

Audiovox

Audiovox APS255A - Car 2 Prestige Platinum Code Learning 3 Button Security... Bedienungsanleitung

Audiovox

Audiovox Platinum Prestige APS-610a Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9675FT Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-150-A Bedienungsanleitung

Audiovox

Audiovox Prestige APS-25CH Bedienungsanleitung

Audiovox

Audiovox Prestige APS-15CH Bedienungsanleitung

Audiovox

Audiovox UltraGuard PRO 9549UG Bedienungsanleitung

Audiovox

Audiovox UTX-ETX Betriebsanleitung

Audiovox

Audiovox Prestige Platinum APS-350-A Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9900 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO-9744WOS2 Bedienungsanleitung

Audiovox

Audiovox 5BCR Betriebsanleitung

Audiovox

Audiovox Prestige 128-8615 Bedienungsanleitung

Audiovox

Audiovox APS-596C Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-785 Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum APS-510 Bedienungsanleitung

Audiovox

Audiovox Pursuit PRO 9842 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung