Autonics DPU Series Bedienungsanleitung



User Manual

Power Controllers

DPU Series

TCD210144AB

  





.autonics.com

ii © Copyright Reserved Autonics Co., Ltd.

-|Transparent setting guide|-

Preface

iii

-|Transparent setting guide|-

Preface

Thank you for purchasing Autonics product.

Please familiarize yourself with the information contained in the Safety Considerations section

before using this product.

This user manual contains information about the product and its proper use, and should be kept in

a place where it will be easy to access.

User Manual Guide

iv © Copyright Reserved Autonics Co., Ltd.

-|Transparent setting guide|-

User Manual Guide

●Please familiarize yourself with the information in this manual before using the product.

● This manual provides detailed information on the product’s features. It does not o󰀨er any

guarantee concerning matters beyond the scope of this manual.

●This manual may not be edited or reproduced in either part or whole without permission.

●A user manual is not provided as part of the product package.

●Visit our web site (www.autonics.com) to download a copy.

●The manual’s content may vary depending on changes to the product’s software and other

unforeseen developments within Autonics, and is subject to change without prior notice.

Upgrade notice is provided through out Autonics web site.

●We contrived to describe this manual more easily and correctly. However, if there are any

corrections or questions, please notify us these on Autonics web site.

User Manual Symbols

-|Transparent setting guide|-

User Manual Symbols

Symbol Description

Supplementary information for a particular feature.

Failure to follow instructions can result in serious injury or death.

Failure to follow instructions can lead to a minor injury or product damage.

An example of the concerned feature’s use.

※1 Annotation mark.

Safety Considerations

vi © Copyright Reserved Autonics Co., Ltd.

-|Transparent setting guide|-

Safety Considerations

●Following these safety considerations will ensure the safe and proper use of the product and help

prevent accidents and minimize hazards.

● Safety considerations are categorized as Warnings and Cautions, as dened below:

●Fail-safe device must be installed when using the unit with machinery that may cause serious

injury or substantial economic loss. (e.g. nuclear power control, medical equipment, ships,

vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster prevention

devices, etc.)

Failure to follow this instruction may result in personal injury, economic loss or re.

● Do not use the unit in the place where ammable/explosive/corrosive gas, high humidity, direct

sunlight, radiant heat, vibration, impact, or salinity may be present.

Failure to follow this instruction may result in explosion or re.

●Install on a device panel, and ground separately.

Failure to follow this instruction may result in re or electric shock.

●Do not connect, repair, or inspect the unit while connected to a power source.

Failure to follow this instruction may result in re or electric shock.

●Do not disassemble or modify the unit.

Failure to follow this instruction may result in re or electric shock.

●Check ‘Connections’ before wiring.

Failure to follow this instruction may result in re.

● Use the unit within the rated specications.

Failure to follow this instruction may result in re or product damage.

●Use a dry cloth to clean the unit, and do not use water or organic solvent.

Failure to follow this instruction may result in re or electric shock.

● Keep the product away from metal chip, dust, and wire residue which ow into the unit.

Failure to follow this instruction may result in re or product damage.

● Since leakage current still ows right after turning o󰀨 the power or in the output OFF status, do

not touch the load terminal.

Failure to follow this instruction may result in electric shock.

● Since leakage current still ows right after turning o󰀨 the power or in the output OFF status, do

not touch the load terminal.

Failure to follow this instruction may result in electric shock.

The specications, dimensions, etc are subject to change without notice.

Be sure to follow cautions written in the instruction manual, user manual and the technical descrip-

tions (catalog, homepage).

Warning Cases that may cause serious injury or fatal accident if

instructions are not followed.

Caution Cases that may cause minor injury or product damage

if instructions are not followed.

Table of Contents

vii

-|Transparent setting guide|-

Table of Contents

Preface.......................................................................................................iii

User Manual Guide ...............................................................................iv

User Manual Symbols...........................................................................v

Safety Considerations.........................................................................vi

Table of Contents ................................................................................. vii

Table of Contents ................................................................................ viii

1. Product Introduction...................................................................... 11

1.1 Features..................................................................................................................11

1.2 Ordering information .......................................................................................12

1.3 Unit description ..................................................................................................13

2. Specications ...................................................................................15

4. Connections.......................................................................................22

4.1 Single-phase (DPU1 series)..........................................................................22

4.2 3-phase (DPU3 series).....................................................................................24

5. Installation and Initial Operation............................................... 26

5.1 Installation.............................................................................................................26

5.2 Initial display........................................................................................................26

5.3 Parameter setting group ................................................................................26

5.3.1 Parameters.................................................................................................26

5.3.2 Monitoring Mode .......................................................................................27

5.3.3 Operation Mode [OP].................................................................................28

5.3.4 Setting Mode 1 [ST-1]..............................................................................29

5.3.5 Setting Mode 2 [ST-2]..............................................................................30

6. Parameter Setting and Functions .............................................32

6.1 Control input ........................................................................................................32

6.2 Functions...............................................................................................................33

6.2.1 Control method [C-MD].............................................................................33

6.2.2 Soft start [ST-T]........................................................................................36

6.2.3 Start limit [S-LM] and start limit time [S-LT].........................................37

6.2.4 Output slope setting [SLOP].....................................................................37

6.2.5 Output slope manual adjustment [A-GA]................................................38

6.2.6 Base-up [B-UP].........................................................................................38

Table of Contents

viii © Copyright Reserved Autonics Co., Ltd.

-|Transparent setting guide|-

6.2.7 Slow up/Slow down [UP-T/DN-T]..........................................................39

6.2.8 Output high limit value [H-OL], Output low limit value [L-OL].............39

6.2.9 Digital input (DI) ........................................................................................40

6.2.10 Proportional and integral constant set of feedback control.................42

6.2.11 Input correction[IN-B].............................................................................43

6.2.12 Input slope correction [SPAN]..................................................................43

6.2.13 Display value content [DISP], bar graph content [BAR]........................43

6.2.14 Load resistance display method [DRES].................................................44

6.2.15 Full load auto recognition [F-LD]............................................................45

6.2.16 Parameter lock [LOCK]..............................................................................45

6.3 Alarm........................................................................................................................46

6.3.1 Overcurrent alarm [OC-A].........................................................................46

6.3.2 Current limit [C-LM]..................................................................................46

6.3.3 Overvoltage alarm [OV-A]........................................................................47

6.3.4 Fuse disconnection alarm [FUSE]...........................................................47

6.3.5 Heatsink overheating alarm [HEAT].........................................................47

6.3.6 Element error alarm [SCR]........................................................................47

6.3.7 Heater disconnection alarm [HB-A]........................................................48

7. Factory Default ................................................................................. 50

8. Maintenance.......................................................................................52

8.1 Fuse..........................................................................................................................52

8.1.1 Single-phase (DPU1 series) .....................................................................52

8.1.2 3-phase (DPU3 series) ..............................................................................53

8.2 Thyristor (SCR) ...................................................................................................53

9. Modbus Mapping Table................................................................. 54

9.1 Function code 3 (0×03) = Read holding resisters..............................54

9.2 Function code 4 (0×04) = Read input resisters ...................................54

9.3 Function code 6 (0×06) = Write single resisters.................................55

9.4 Function code 16 (0×10) = Write multiple resisters ..........................55

9.5 Address mapping table...................................................................................56

9.5.1 Input resisters ...........................................................................................56

9.5.2 Holding resisters.......................................................................................58

Table of Contents

1. Product Introduction

-|Transparent setting guide|-

1. Product Introduction

1.1 Features

●High speed and high accuracy by digital control using high speed CPU

●Various controls

- Phase control, feedback control (constant voltage/constant current/constant power)

- Zero crossing cycle control (xed/variable cycles)

- Zero crossing ON/OFF control

●Improved maintainability with built-in fast-acting fuse and easy fuse replacement

● Communication output model: RS485 (Modbus RTU)

●Various control inputs and DI inputs

- control input: analog (current, voltage), ON/OFF (voltage pulse, no voltage), communication (RS485),

potentiometer

- DI input: AUTO/MAN switching, RUN/STOP switching, Reset, output holding, SP designation (6 set-

ting points can be customized)

●Various alarm output

- Overcurrent, overvoltage, fuse break, heat sink overheat, device fault, heater break alarm (partial

heater break detection)

●Improved convenience by separating operation part

●Applicable load

- Supercantal, platinum, molybdenum, carbon, halogen lamps, chrome, nickel, etc.

Table of Contents

12 © Copyright Reserved Autonics Co., Ltd.

-|Transparent setting guide|-

1.2 Ordering information

Control phase

Item

Rated current

capacity

Size

Power supply

Option

DPU Digital Power Controller Unit

R RS485 communication

DRemote Display Unit

ARemote Display Unit

+ RS485 communication

N No option

1 110VAC

2 220VAC

3 380VAC

4 440VAC

1 Single-phase

3 3-phase

Single-phase 3-phase

A 0 to 70A 0 to 50A

B 80 to 200A 70 to 200A

C 250 to 350A

D 400 to 600A

EOption

025 25A 200 200A

040 40A 250 250A

050 50A 350 350A

070 70A 400 400A

080 80A 500 500A

100 100A 600 600A

120 120A

150 150A

180 180A

1 2 ADPU 025 R

Andere Handbücher für DPU Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Autonics Controller Handbücher

Autonics

Autonics TZN Series Bedienungsanleitung

Autonics

Autonics TC4S Bedienungsanleitung

Autonics

Autonics PMC-HS Series Bedienungsanleitung

Autonics

Autonics MD5-HF14 Series Bedienungsanleitung

Autonics

Autonics PA10-U Bedienungsanleitung

Autonics

Autonics DPU Series Bedienungsanleitung

Autonics

Autonics SFC-R Series Bedienungsanleitung

Autonics

Autonics TC3YT Series Bedienungsanleitung

Autonics

Autonics SPR1 Series Bedienungsanleitung

Autonics

Autonics TZ4SP Bedienungsanleitung

Autonics

Autonics SPR1 Series Bedienungsanleitung

Autonics

Autonics TF3 Series Bedienungsanleitung

Autonics

Autonics PA-12 Series Bedienungsanleitung

Autonics

Autonics SPR3 Series Bedienungsanleitung

Autonics

Autonics SPR Series Gebrauchs- und Pflegehandbuch

Autonics

Autonics PMC-1 HS Bedienungsanleitung

Autonics

Autonics TC4S Bedienungsanleitung

Autonics

Autonics TZ Series Bedienungsanleitung

Autonics

Autonics TF3 Series Bedienungsanleitung

Autonics

Autonics TN Series Gebrauchs- und Pflegehandbuch

Autonics

Autonics 1-Axis High Speed Stand-Alone Series Bedienungsanleitung

Autonics

Autonics DPU1 Series Bedienungsanleitung

Autonics

Autonics AiS Series Bedienungsanleitung

Autonics

Autonics TN Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch